EP45-UD3P Benches 3D at 670mhz+ FSB

Printable View

Show 100 post(s) from this thread on one page

10-15-2008, 09:01 PM
dinos22

what
you killed that nice E8600 asswipe eeeeeek
someone slap Thomas quick
10-16-2008, 07:36 PM
Brian y.

@hicookie

CPU PLL @1.81v?:confused:

What CPU/NB skew did you use for that 3D run?
10-16-2008, 07:42 PM
[XC] gomeler

Quote:

Originally Posted by Pt1t

i cant, i killed it yesterday :(

:ROTF: Ish happens, it's a good thing they are relatively cheap. Kill it sub-zero or on air?
10-16-2008, 11:48 PM
Pt1t

Quote:

Originally Posted by [XC] gomeler

:ROTF: Ish happens, it's a good thing they are relatively cheap. Kill it sub-zero or on air?

sub 100 and after air :rolleyes: , good thing ... RMA accepted, now i hope new one will be as good as my dead chip.
10-17-2008, 09:41 AM
redratamd

EP45-UD3P @home :)
10-17-2008, 10:13 AM
[XC] gomeler

Quote:

Originally Posted by Pt1t

sub 100 and after air :rolleyes: , good thing ... RMA accepted, now i hope new one will be as good as my dead chip.

I hope for the best. Maybe you'll get a 6500+MHz chip :yepp:
10-17-2008, 10:47 AM
Pt1t

Quote:

Originally Posted by [XC] gomeler

I hope for the best. Maybe you'll get a 6500+MHz chip :yepp:

my chip was +6500 chip :(
10-17-2008, 12:04 PM
[XC] gomeler

Quote:

Originally Posted by Pt1t

my chip was +6500 chip :(

k I hope you get a 6600+MHz chip :D
10-17-2008, 12:12 PM
PPInDaHouse

This board looks really nice, can't wait to test one :D
10-18-2008, 08:35 AM
redratamd

I can't take more 600MHz for Spi 1M :( But easy boot with the memory on Cas 4 with 5:6 .
10-18-2008, 01:38 PM
Gautam

I can't even enter Windows at 500, and 450MHz randomly BSODs on two different E8600's.

I really hope there's something (very) stupid I'm missing.
10-18-2008, 06:14 PM
Brian y.

Quote:

Originally Posted by Gautam

I can't even enter Windows at 500, and 450MHz randomly BSODs on two different E8600's.

I really hope there's something (very) stupid I'm missing.

I had same exact issue.

Setting CPU Clock Drive to 800, PCIe to 900 & CPU clock skew to 200 allows me to boot up to 550 but is maxed out at 600FSB.

I have had poor performing FSB wise mobo's before such as the Biostar T45 and DFI Dark and after rma'ing them both was blessed with some FSB monsters. Looks like I am going to have to do the same with this one.
10-18-2008, 09:09 PM
bigslappy

any one know what water blocks work on the mosfits & chipsets on this MoBo ? I know the EK Asus3a looks to fit the mosfits
10-18-2008, 09:14 PM
road-runner

Quote:

Originally Posted by bigslappy

any one know what water blocks work on the mosfits & chipsets on this MoBo ? I know the EK Asus3a looks to fit the mosfits

I have a dtek fuzion, not the new one on a P45 DS4P and a Dtek fuzion with pro mount on the P45 UD3P also not the new one...
10-18-2008, 09:16 PM
Gautam

Quote:

Originally Posted by Brian y.

I had same exact issue.

Setting CPU Clock Drive to 800, PCIe to 900 & CPU clock skew to 200 allows me to boot up to 550 but is maxed out at 600FSB.

I have had poor performing FSB wise mobo's before such as the Biostar T45 and DFI Dark and after rma'ing them both was blessed with some FSB monsters. Looks like I am going to have to do the same with this one.

Thanks, I'll give it a shot. I've always been FSB challenged. :p:
10-19-2008, 02:59 AM
MACMAC

500Mhz @ 1.24V HyperPi 32M & 3D stable
525MHz @ 1.30V HyperPi 32M & 3D stable
550Mhz is hit & miss in H-Pi 32M, haven't really found the trick...voltage isn't it :D

Looks like some finesse is called for with this board.
10-19-2008, 03:44 AM
Devious

So looking at the general results we can assume the initial posts were on cherry picked hardware.
10-19-2008, 03:58 AM
antoine76

Quote:

Originally Posted by Brian y.

I had same exact issue.

Setting CPU Clock Drive to 800, PCIe to 900 & CPU clock skew to 200 allows me to boot up to 550 but is maxed out at 600FSB.

I have had poor performing FSB wise mobo's before such as the Biostar T45 and DFI Dark and after rma'ing them both was blessed with some FSB monsters. Looks like I am going to have to do the same with this one.

Try with more vFSB (vtt) ;)
10-19-2008, 04:40 AM
MACMAC

Ok, since I was having more luck in 3D than SPi I decided to go that route, it's looping 3DMark2001 at 600Mhz 1:1 PL11 S.C with 1.56 vNB

Not too pleased with the PL11, but should be able to lower it back down to PL 10 with some fine tuning.

Once above 500Mhz, the board auto sets 1.60VTT and 1.86PLL...might be overkill :D
10-19-2008, 04:55 AM
PPInDaHouse

1.86vpll looks too high for aircooling :rolleyes:
10-19-2008, 05:02 AM
Pt1t

http://valid.x86-secret.com/show_oc.php?id=432489

it was the last test of my burned E8600 , VTT 1.55v ,vNB 1.6v. PL10
10-19-2008, 05:04 AM
PPInDaHouse

Quote:

Originally Posted by Pt1t

http://valid.x86-secret.com/show_oc.php?id=432489

it was last test of my burned E8600 , VTT 1.55v ,vNB 1.6v. PL10

what cooling?
10-19-2008, 05:09 AM
HousERaT

What bios are people using F4 or F5A?
10-19-2008, 05:17 AM
Pt1t

Quote:

Originally Posted by PPInDaHouse

what cooling?

2 stages cascade.... 650*9 run before to try x10 ... But now cpu rip.

it was 3d stable .
10-19-2008, 05:26 AM
PPInDaHouse

Quote:

Originally Posted by Pt1t

2 stages cascade.... 650*9 run before to try x10 ... But now cpu rip.

it was 3d stable .

you mean 650x10 3D stable? that was nice, hope you can get a similar or better one :)

Show 100 post(s) from this thread on one page