thank u friend:),Quote:
Originally Posted by BuGjAE
seems it needs at least 1.38v compare to 9*422 at only 1.2v:up:, its 8gigs though, awsome board and it handles this cheap E7300 very well :clap:
http://www.prototype.web.id/forum_im...33_Everest.jpg
ram is bottlenecking me.. 1070 and it wont stabilize, even as high as 1.45vNB and 2.25vDimm :down:
thx
asap
asap,good job,mine was very hard to stabilize using 8GB memory at about 533fsb-550fsb,like you vnb and vdimm lost its effect once i went higher than 533.i got it to 550fsb ran 5 runs of IBT(took 1 1/2 hrs with 8GB)seemed stable then ran prime for 2 hrs and everything was good for a couple of days,then one day it failed to boot,so i tried making some adjustments, but no luck so i backed it back down to 538fsband that did the trick.i think it was just too much for the memory controller or the NB to handle.again great job!
thx, radaja
yes, been hard time stabilizing 8gigs, it was stable enough for 530fsb, then i decided to try 533 and see how it goes for the same settings..
at 530fsb, from MCH Ref at 65, 66, 70, 72.. i guess 72 fits me, the other will fail blend within a minute
http://www.prototype.web.id/forum_im...30fsbsmall.jpg
thx
asap
Quick run blend before i go for weekend with my daughter :up:
same settings as 530fsb, hopefully i can make 550 after i got back... and thank u for all you guys here, got lots of info with this amazing board,
http://www.prototype.web.id/forum_im...rthosSmall.jpg
happy weekend :)
asap
well, my 9650 is installed and up and running.just stressing it at stock to see how warm it gets.looks like two sensors are stuck at 36c and 31c,but thats just fineall my other cpu's had stuck ones at 39c.vid is 1.25 which im happy with ,since my e8400 with a vid of 1.23 ran so hot yet my e8500 with vid of 1.25 was just right.http://i43.tinypic.com/2wch9x0.jpg
When I tried running the .exe that gigabyte provided it told me that it was for 32 bit only and to contact them for a 64 bit one. :confused:Quote:
Originally Posted by nugzo
Unzip EXE > Save bios file only to a pen drive > go to bios > load optimized default with usb keyboard and storage support > insert the usb drive with bios file > save and exit > boot screen hit END key > on QFlash Update Bios from Drive > Choose HD _0X (Pendrive) > Update bios > Restart > Load Optimized Defaults > Save Exit then go to bios and load your profile...Quote:
Originally Posted by l33t p1mp
Hey guys, here is a screen shot of my settings - I am running e8400 @ 500x8 and just need to get that last little bit of stability.
specs are:
e8400
ud3p
8gb (4x2gb)of mushkin redline 996593
the system can run ibt with the posted settings but will bsod vary randomly -usually while doing nothing...
Probably raise the MCH volt or RAM volt to 2.0v.
maybe loosen the timings on your ram too.
Which timings would you recommend I loosen?Quote:
Originally Posted by radaja
What would be a safe MCH?Quote:
Originally Posted by fatguy1992
tras-15 / trfc - 55-68. safe mch is up to how well your cooling is.i have a fan on my nb. so i used up to 1.42 for 8x550fsb with 8GB of ram for it to be stable.but for starters try 1.36-1.38.
ok thanks - i will give that a try...
well after letting the new cpu prime for a few hrs at stock settings,i went for 3.8.just started priming but heres a quick ss.im pretty happy with the temps so far,it about on par with my e8500.i was worried cause everyone says that quads run considerably hotter.but i think ill be ok.http://i41.tinypic.com/15nku13.jpg
OK, So I got my new UD3R, thinking my other one was screwed up. If you can remember, for some reason my motherboard will not run 2 sticks of ram no matter what size. So I bought a new mobo since newegg would not replace and gigabyte still has not sent me any kind of RMA confirmation for the mobo. Anywho, fast forward to today. I got the motherboard, rev 1.1(interesting the NB/Sb coolers are a bit different in finish and sizes then from rev 1.0) so i reinstalled with new motherboard. Well, this one won't run with 2 modules either. Also, once I installed it, it would hang as soon as my desktop came up. So i grabbed a spare HDD and installed Windows fresh. No more hang but I still can only run one module. If I put 2 modules in it won't even get to bios.
Does anyone have any clue what this may be from? I am thinking maybe a PSu issue, as my HX520 is almost 2 yrs old now, but for the past 3 weeks, I have been running at 471x8.5 with no issues, except the ram issue. I am so puzzled right now. I have 5 different sets of ram that I have tested with all the same effect...1 stick=mobo runs, 2 sticks= mobo won't post even to bios.
Having trouble with Orthos Blend Stable...any suggestions.
[URL=http://imageshack.us]http://img237.imageshack.us/img237/4...blendfayt6.jpg[/
bluestang,try 1.36-138 mch and maybe try to drop mch reference voltage one notch,also might just need more vcore.but i suspect its the mch voltage,you are running 4GB of ram at 525fsb.my voltages were exactly the same as your,except i used 1.38-1.40 mch volts and my mch ref volts always showed up on ET6 as 0.70.with 1.28vtt,the exact mch ref setting is 0.750.so maybe give this a try.
radaja, thanks...I'll give that a try and see what happens. I'd like to getmy ram to run @ 1:1 538 FSB, but we'll see. Is 1.38 safe for 24/7 ??
as long as it doesnt get hot.get some good airflow over the NB and you should be good.
The max safe MCH volt is 1.6v as long as the cooling is good enough. Good enough is not exceeding 60C or so under load. Therefore I recommend putting a fan on it.Quote:
Originally Posted by arctic-k20
@radaja
Awesome temps :up:
What do u have on ur TRUE?
yes i have a true.with two 1900rpm fans
Nice :up:
First: Sorry for my bad English.
I have the same Problem like Jor3lBR with 2x2048MB RAM, DDR1066 and MCH-Voltage, he discibes on Page 58/59.
but it is more bad, my "Stuck" MCH -Core is 1,2V!!
Corsair Dominator 2x2048MB DDR 1066 5/5/5/15, the CPU is a Q9550 E0.
When i set everything to DEFAULT (FSB333x8,5, DDR1066) i can boot and everything is fine. Even DDR 1080 is no Problem.
But when i raise the MCH-Core Voltage over 1,2V the Board loop in Reboots. I must turn down FSB to 325 (DDR 1040), then i can boot.
I need higher MCH-Core Voltage then 1,2V for my Quad at higher FSB, but then i cant run DDR 1066or higher!
(For Example FSB 445 and 2.4B=1066 -> not possible over 1,2V MCH
FSB 433 and 2.4B=1040 -> possible with 1,2-1,4V)
What is the Problem, is the Board damaged or the RAM incompatible?
Any solution?