tnx man ;)Quote:
On a DFI P35. Still, nice result.
your tg pc6400 has gkx or gmh chip?
Printable View
tnx man ;)Quote:
On a DFI P35. Still, nice result.
your tg pc6400 has gkx or gmh chip?
On P45 (not a DFI) you will need around 540 FSB to break 11K read without using a high CPU clock to 'cheat'.Quote:
Originally Posted by Ch@pS
You can see in the SS below I am close to 11K at 533 FSB, but to get the FSB any higher I had to back off some chipset settings so I lost some efficiency, which means I had to go up to 540 FSB (shown on second SS) to break 11K.
http://i720.photobucket.com/albums/w...edCTstrong.jpg
Here is a run that is the lowest settings I can use to break 11K read. I use a low CPU clock of 3.78GHz so it just shows the raw power of the FSB and ram speed.
http://i720.photobucket.com/albums/w...MHz11Kread.jpg
i'll try your same settings cryptic, just to verify if it's true that m2f sux at speed against ud3r p45. i've heard about it but i never verified :)
the new ep45 extreme is here :D
go for extreme oc man, i'm waiting screens...will it be pwnage? :D
I am waiting for your screen :)Quote:
Originally Posted by Mafio
this afternoon i tried the crucial ballistix of my friend Guglio on my new ep45 extreme. :yepp:
this ram is spectacular...
1400mhz cas5 2.4volt
http://www.pctunerup.com/up/results/..._screen010.jpg
1200 cas4 2.4volt
http://www.pctunerup.com/up/results/..._screen011.jpg
1225 cas4 2.45 volt
http://www.pctunerup.com/up/results/..._screen012.jpg
well done :clap:
but...no more than 1400 cas5? do you try 2.5+v? :D
@Mafio good start.....now overclock the ram :)
This is my new Patriot kit on 2.06V real:
Pulled these from and old HP Media Center PC. Loving them allready. I know they will go higher but I cant seem to get my DFI BloodIron P35 board to do it.It craps out past 1150 dual channel. I must not being doing something right.
DDR2 1100 Cas5 @ 2.0v
JEDEC PCB probably holding you back.
doubtful they are pretty good as far as PCB's go same PCB my D9DCD's use and those do 1120 CL4Quote:
Originally Posted by Shiranui Gen-An
I dont think its that because I have a pair of OCZ Reaper 1150s that will do 1150 single channel but not dual channel. I think its the auto timings the board giving it but im not sure what sub timings to change to give stability. Or I'm just bad with ram lol.Quote:
Originally Posted by Shiranui Gen-An
I've run some D9's up to 1350 CAS 5 in dual channel on Blood Iron, for what its worth.
If you could help me achieve that it would be greatly appreciated.:up:Quote:
Originally Posted by tool_462
i have been 1200 or soQuote:
Originally Posted by tool_462
Ballistix Tracers, double sided. 2.35v 1300Mhz. I believe this pair is GKX, but I'm not sure. The don't like T1 and cas 3, but they scream with cas 4 and 5. ICs just say 'Ballistix' and '-f17' Not totaly stable at 1300. Can run SuperPi and other benchies but crap in RL gaming.
http://valid.canardpc.com/show_oc.php?id=519358
rotfl! hp building ht pc with high end ram...incredible :)Quote:
Pulled these from and old HP Media Center PC.
I couldn't believe it either. I have been looking everywhere for some sticks of D9 and i found them in the one place you wouldnt think to look, An HP:shocked:Quote:
Originally Posted by simone18
you would be surprised but i seen many d9 in hp pcs:yepp:Quote:
Originally Posted by Bigred1
OMGQuote:
Originally Posted by simone18
cellshock pc8000 + crucial ballistix pc8500 on my ep45 extreme
1200mhz cas4 @2.4volt ;)
http://forum.hwproject.net/imagehost...15bd6221a3.jpg
guys, this mobo kick ass :yepp:
congratulations....really a good result with 4 dimm ram :)Quote:
Originally Posted by Mafio
great job mafio.