Printable View
Okey, now my board is ready for some action.
I use Enzotech heatsink for the mosfet and SB.
Koolance for the NB (Itīs very flexible, I have used it on several boards and it do the jobb very well).
D-Tek Fuzion for the CPU with Xigmatek Crossbow backplate.
http://i282.photobucket.com/albums/k...reme/RE102.jpg
http://i282.photobucket.com/albums/k...reme/RE103.jpg
Hi,
does someone have information over the speed (DRAM Frequency and Strap ) of 4x1gb memory with a q9650 based on a RE board?
Thanks
regards
achim
Ugh. I've spent the better part of the past two days playing with settings trying to get anything over 1200MHz to even get into Windows and I've had no luck whatsoever.
Bios 0601
Totally stable at FSB 500 DDR3-1200
But lowering FSB, changing dividers, playing with skews...nothing gets me anything more.
I had the same bandwidth/latency with my Maximus Formula and DDR2 :(
I see you say you've tried Expat Griz's settings, have you tried experimenting with these.
NB DDRVref: +15mv
DDR3 ChannelA Vref: +50mv
DDR3 ChannelB Vref: +50mv
Sounds a bit of nightmare.
RLM
Wow, sorry to hear that Jack!! What kind of volts are you pushing through the ram? Is it BSODing?? Post your settings so everybody can see where you are at. I'm bashing Crysis right now, everything on very high at these settings.:DQuote:
Originally Posted by zlojack
Well, I've finally got somewhere. These settings passed one run through Memtest86+ and now I've bumped the FSB to 490 and will run HCI Memtest and see what happens. With 500FSB I get DETDRAM with these settings, so I probably need to tweak something as I get up towards higher bus speeds.
I was so frustrated this afternoon that I put my board and RAM up for sale and started looking for a DDR2 board :ROTF:
I've since taken them off the market... I figure I've got to give this board more of a chance and at least wait until I get proper cooling.
Quote:
Bios 0601
Extreme Tweaker
Ai Overclock Tuner: Manual
OC From Memory Level Up: Auto
FSB Frequency: 485
CPU Ratio Setting: 7
CPU Configuration
C1E Support: Disabled
CPU TM Function: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Disabled
Execute Disable Bit: Disbled
Core Multi-Processing: Enabled
CPU Clock Skew: Normal
NB Clock Skew: Delay 300ps
FSB Strap to North Bridge: 333
PCIE Frequency: 102
DRAM Frequency: 1553Mhz
DRAM Command Rate: 1N
DRAM Timing Control: Manual
1st Information: 8-8-8-18-5-72-12-6
CAS# Latency: 8
RAS# to CAS# Delay: 8
RAS# Pre Time: 8
RAS# ACT Time: 18
RAS# To RAS# Delay: 5
REF Cycle Time: 72
WRITE Recovery Time: 12
READ to Pre Time: 6
2nd Information : 9-6-6-4-7-4-7
READ to WRITE Delay (S/D): 9
WRITE to READ Delay (S): 6
WRITE to READ Delay (D): 6
READ to READ (S): 4
READ to READ (D): 7
WRITE to WRITE (S): 4
WRITE to WRITE (D): 7
3RD Information: 20-8-1-9-9
WRITE to PRE Delay: 20
READ to PRE Delay: 8
PRE to PRE Delay: 1
ALL PRE to ACT Delay: 9
ALL PRE to REF Delay: 9
DRAM Static Read Control: Enabled
DRAM Dynamic Write Control: Enabled
DRAM Skew Control
DRAM CMD Skew on Channel A: Normal
DRAM CLK Skew on DIMM A1: Normal
DRAM CLK Skew on DIMM A2: Adv. 250
DRAM CTL Skew on DIMM A1: Normal
DRAM CTL Skew on DIMM A2: Normal
DRAM CMD Skew on Channel B: Normal
DRAM CLK Skew on DIMM B1: Normal
DRAM CLK Skew on DIMM B2: Adv. 250
DRAM CTL Skew on DIMM B1: Normal
DRAM CTL Skew on DIMM B2: Normal
Ai Clock Twister: Moderate
Ai Transaction Booster: Manual
Common Performance Level: 08
Pull-In of CHA PH1: Disabled
Pull-In of CHA PH2: Disabled
Pull-In of CHA PH3: Disabled
Pull-In of CHB PH1: Disabled
Pull-In of CHB PH2: Disabled
Pull-In of CHB PH3: Disabled
EPU II Phase Control: Auto
CPU Voltage: 1.25
Load-Line Calibration: Disabled
CPU PLL Voltage: 1.60381
FSB Termination Voltage: 1.41816
CPU GTLVerf (0): +50mv
CPU GTLVerf (1): +50mv
CPU GTLVerf (2): Auto
CPU GTLVerf (3): Auto
NB GTLVerf: +40mV
North Bridge Voltage: 1.66 (Didn't write the exact value, Everest says 1.66v)
DRAM Voltage: 2.0 (Didn't write the exact value, Everest says 2.0v)
NB DDRVref: +12.5mv
DDR3 ChannelA Vref: +50mv
DDR3 ChannelB Vref: +50mv
South Bridge 1.5 Voltage: 1.61706
South Bridge 1.05 Voltage: 1.11339
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
Far from world beating, but just messing around and experimenting with voltages. Trying for less is more with PLL VTT etc.
http://img389.imageshack.us/img389/5...rime32bqp2.jpg
http://img98.imageshack.us/img98/5136/wprime1024sn7.jpg
RLM
Took longer than expected and had a nightmare with the cable management but well pleased with the results :D.
Now for some serious benching ;)
Attachment 88796
With no flash .....
Attachment 88797
this board is tough...
has anyone manage to get 4x1gb kits to 2000mhz yet..
http://www.keepandshare.com/doc/view.php?id=894393&da=y
The above link is to Bios version 0801, dated 11/07/2008 for the Rampage Extreme.
Also hese is the link to the Asus Forum Post. http://vip.asus.com/forum/view.aspx?...Language=en-us
Thanks Kensek.
Will give that a try when I get home.
Ok...this is strange.
I tested 495 FSB last night with the RAM at 1585 MHz (with the settings from my previous post) and it passed HCI 800%.
So this morning I tried to boot it up at 500 FSB and get DET DRAM.
However, 498 FSB boots. I have left it running HCI Memtest so we'll see how it goes. I also lowered CAS to 7. If I can't get the frequencies higher, I'll try tightening the timings.
Maybe I'll see what bios 0801 can do. 0701 was brutal...wouldn't save my settings and just constantly rebooted.
EDIT: 498 FSB with RAM at 1594MHz is chugging along with no errors :confused:
I'll try 499 when I get home and see what happens.
quite inefficient performance for the clocks, but still pleased with 3x13K anyway :)
http://i447.photobucket.com/albums/q...24_AXE_EV1.jpg
http://i447.photobucket.com/albums/q...24_AXE_EV2.jpg
Write and Copy scaling with FSB, but only just managed 13K+ Read/sub 40ns with 8-8-8-24 (5:8) and PL9. (vNB 1.7V / 0403 BIOS)
need some lower latency DIMMs really: 8-8-8-20 / 24 is the best I can get above 900mhz. CT is on AUTO, so losing there aswell. No clean Windows boot above 615fsb with any other CT so far.
Can anyone re-host the 0801 file? Apparently Kensek has exceeded his bandwidth for the day :D
Nice work there Cheapseats! This board definitely does the business with 2x1GB kits.
There is No bandwidth limitation.
I apologize, didn't know.
I just checked it out.
I host 50 different Asus Bioses so maybe the new S2E and R2E and RE ones are being downloaded in mass quantities.
Yes indeed 81 downloads of RE and 18 of the S2E today
It would cost $249.99/yr to upgrade to unlimited downloads from my BIOS repository.
Screw that!!!
Cheers Kensek:up:
RLM
Well, I started up my rig with 2x1 Corsair Dominator PC-14400 (XMP) and it booted up just fine and I was surprised when I noticed that it started with the XMP profile instead of the usually 1333 9-9-9. Everything was on auto.
Did install some applications and games and played some with that setting and it was stabil as a rock.
Now itīs time to find a good 24/7 gamer setup, I will be back for more.
This is the Cache & Memory Benckmark on auto (the tRD was 6 according to Memset)
http://i282.photobucket.com/albums/k...RFC100tRD6.png
My Doms love this board - have fun :up:Quote:
Originally Posted by Ghostleader
ThanksQuote:
Originally Posted by rob2k
Have you been able to run FSB 500 and 2000+ and 8-8-8 tRD7 with them?
No my quad is on its limit of 475. I found this useful from a review of the memory. Can't remember where its from though ........Quote:
Originally Posted by Ghostleader
Attachment 88850
So has anyone tried the 801 bios...I would but waiting on RMA on my board...Ive had the best luck with 403 but havint tried 7xx or 8xx yet.
I tried 0801 and got no changes or further luck using my previous settings. Still capped stable at 498 FSB but won't post at 500 :(
I think this board needs more patience than I've got.
I tried it and my best settings would not even complete one loop in HyperPi so flashed back to 0501 as there is too much time involved finding the one or more setting to correct it. I would probably recommend only flashing to 0801 if it fixes an issue you have - difficult without a changelog - or if you are getting the board new and do not have any previous working settings.Quote:
Originally Posted by gmod
Hi all,
seem to have run into a small but anoying issue.
I only have a usb mouse and a usb keyboard plugged into the mobo at the moment yet when the system boots and comes up with the usb scanning, it now reports 2 keybords and 1 mouse?
Has anyone else had this? any ideas on what might be causing this?