Sheas, I see one parallel to my C1-9500. He also stopped working at relative low volts in comparison to what i had applied before.Quote:
Originally Posted by aGeoM
You plan to RMA that CPU or do you think it was your fault only? I mean both board and the chip are build for overclocking and you ran your cpu in specs at modest higher voltages.
How do you make those templates? like the ones in your early posts which were scrollable, LOL "scrollable" wonder if that's even a proper word.Quote:
Now ....Who's gonna be a Gentleman and give me the Edited Notepad File with the Updated Bios Template?
BUT isn't C1 the last step in POST before the CPU becomes important/needed?Quote:
Originally Posted by KTE
Could the CPU fail badly enough that the POST might not make it past the C1 error and into one of the CPU POST messages?
NOTE: I never verified if my DFI was bad or not. I RMA'ed it. But the Phenom is definitely bad in a different motherboard with two different sets of memory. (The 1066 memory has tested fine for a day including 2 passes of memtest. At 800 speeds at this time. No overclocking until everything has worked for a few days at stock.)
Use the CODE tag like the QUOTE tag for scrollable stuff. ;)Quote:
Originally Posted by illogical
Oh damn, Im such a retard. I prime all time with small FFT's and got like'em0 as it still crashed... But the description for small FFT's is clearly 'fits within L2 cache'... To make it more clear, I Prime large FFT's with small FFT's stable settings and it crashed hard within minutes...
KTE, or anyone else having problems with Prime not being stable, what Prime option did you actually use to test?
And Brother, you've no issues at all hm? How do you determine whether your Phenom is stable or not? What tests?
Im so stupid, no matter if I just found the 'solution' or not, for testing small FFT's which doesnt stress anything else than CPU cores...
perhaps it could be somewhat useful compare small fft with large fft results..
perhaps small fft-stable can be made large fft-stable when lowering nb or htt or such?
Attention:....."New" D.F.I LanParty UT 790FX-M2R / Phenom 4/15/2008 "Bios Template" Click Attachment Link Below!:up:
DFI LANPARTY UT 790FX-M2R (BIOS 4/15/2008 "Beta")
AMD Phenom 9850 Black Edition "B3"
Tuniq Tower 120
OCZ Reaper HPC (PC2-8500) 5-5-5-18 2X2GB
POWERCOLOR AX3870 X2 CROSSFIRE CATALYST 8.3
Auzentech XPlosion
Areca 1231 ML {Intel IOP 341} ~ 6 ~ 250gb Hitachi Sata II Raid 6 ~2~WD 74gb Raptors ~ Raid 0 ~
Plextor 750A
SilverStone OP1000
CM Stacker STC-T01
Code:>HT Link Control:
HT Link Width......................... - 16 bit
HT Frequency.......................... - 2GHZ MHz
IH Flow Control Mode.................. - Disabled
HT Link Tristate...................... - Disabled
2x LCLK Mode.......................... - Disabled
Unit Id Clumping...................... - Disabled
>CPU Feature:
CPU DID.............................. - 1
CPU FID.............................. - 0C
CPU-NB DID........................... - 1
CPU-NB FID........................... - 06
AMD CPU stepping..................... - P0
>DRAM Configuration:
MCT Memory Timing.................... - Manual
2T Mode.............................. - Auto
Cas Latency Time..................... - 5
Pre Charge Delay (tRAS).............. - 18
DRAM RAS# Precharge.................. - 5
DRAN RAS# to CAS# Delay.............. - 5
Bank to Bank Cmd (TRRD).............. - Auto
TRC.................................. - 23T
TRTP................................. - Auto
Write Recovery (TWR)................. - Auto
Write-Read Command (TWTR)............ - Auto
TRFC0................................ - 195ns
TRFC1................................ - 195ns
TRFC2................................ - 195ns
TRFC3................................ - 195ns
Trdrd................................ - Auto
TrwtT0............................... - Auto
Twrrd................................ - Auto
Twrwr................................ - Auto
CS/ODT Pin Fine Delay................ - Enabled
Bank Swizzle Mode.................... - Enabled
Auto Tweak Performance............... - Enabled
Optimal Performance Mode............. - Enabled
>ODC Control Mode:
DRAM Drivers Weak Mode.............. - Normal
Output Drivers Comp................. - Normal
>Channel A:
CPU On-die Termination.............. - 300 ohms +/- 20%
DQS Drive Strength.................. - 1.00x
Data Drive Strength................. - 1.00x
MEMCLK Drive Strength............... - 1.00x
Addr/Cmd Drive Strength............. - 1.50x
CS/ODT Drive Strength............... - 1.50x
CKE Drive Strenght.................. - 1.50x
>Channel B:
CPU On-die Termination.............. - 300 ohms +/- 20%
DQS Drive Strength.................. - 1.00x
Data Drive Strength................. - 1.00x
MEMCLK Drive Strength............... - 1.00x
Addr/Cmd Drive Strength............. - 1.50x
CS/ODT Drive Strength............... - 1.50x
CKE Drive Strenght.................. - 1.50x
>PWM Settings:
PWM Control.......................... - Enabled
CPU VID Control...................... - 1.2500v
CPU Vid Special Add.................. - Auto
CPU NB Vlotage Control............... - Auto
CPU NB Vid Special Add............... - Auto
DRAM Voltage Control................. - 1.80v
SB PLL 1.2V Voltage.................. - 1.20v
NB Core Voltage...................... - 1.250v
NB PCI-E Voltage..................... - 1.120v
NB HT Voltage........................ - 1.270v
Genie BIOS Settings:
Timing Mode.......................... - Manual
Memory Clock value or Limit.......... - DDR 1066
PCIE 3,4 State....................... - Auto
PCIE 2 State......................... - x2
CPU TLB Cache Fix.................... - Disabled
AMD K8 Cool & Quiet control.......... - Disabled
CPU Clock Ratio...................... - Auto
Spread Spectrum...................... - Disabled
CPU Host/HTT Clock................... - 200mhz
CPU Host/HTT Boot Up Clock........... - 200mhz
CPU Host/HTT Adjustment Gap.......... - 5mhz
PCIE Clock........................... - 100mhz
I dont know, if this would be any help to you guys that are stress testing or not...but I would try using S&M stress test...It has been the one and only program that has gotten my cores heated up as much as it does .. about 7C over orthos on air cooling(when doing FPU test). It also tests multiple parts of your processor and tests RAM also and HDD(all optional via selection). It also will do any number of CPU cores...does quad cores in single instance of itself. only stress program Ive found that does that.
Its easily available through hirens boot CD in windows using the wintools on his CD. Also...can be downloaded but I couldnt get the downloaded newest version to work right....for some reason..probably was just me =)
Most likely. I dropped HTT to 200 from 207. This dropped CPU speed to 2.8Ghz again, but let the NB and HT run on default speeds too. Where as it froze within 10 minutes with Large FFT's it's already running for over an hour now.Quote:
Originally Posted by Oese
:up: :toast: Thank you for the effort you put into this.Quote:
Originally Posted by Brother Esau
Hey Guys need some input please:) ....Should we start a Dedicate DFI LanParty UT 790FX-M2R thread for Phenom Database? I would like to but have mixed feelings on this as I do not wish to make users with Dual Core X2 feel left out or shunned in any fashion! That would not be the intention at all but perhaps some may perceive it that way don't know:shrug:
AFAIK on AMD CPUs, its one of the last processes ->Quote:
Originally Posted by keithlm
http://img59.imageshack.us/img59/1046/amdbspij3.png
So yeah, it can be bad BIOS, bad 1066 BIOS code, bad 1066 DIMM support or an IMC error. If you check the system power when you get the C1 error, the CPU is never fully started up, only around 5/6th of it is starting up at most before it reboots/pauses. That would point to IMC failing to start up. IMC not being initialized is what MB MFGs told me that error is with Phenom, especially for my last 3. But like I told you, all of mine did show that problem brand new at one time or another - but when tried in another board, they booted fine. My new 9850 gave the same problem first time and now.
Only ever happens when I clear CMOS, switch off mains power or remove the power connection.
The day it boots, it will run perfectly fine again for months unless and until I do these procedures. :shrug:
MSI and Abit have not been able to reproduce the problem internally. I've done so much testing and troubleshooting working this error out, 5000 Miss Universe contestents side by side on La Jolla's Black Beach [according to its rules :D] would now only have an anaphrodisiac affect on me :(
Stability: casual daily use, doing everything without worry or caution including benching, stability tests and so on should all give no probelms, ever - that's stable for us. With Phenom the procedure is lengthier than anything I've used before though.
My last setting was 2800 fully Load/WISE stable for 3 days at 1.384v... then did a lot of messing and after 3 more days [planned], decided to test it again -> what a surpirse, it failed WISE stability even at 1.4v now :rolleyes:
This is on a CPU which 3069MHz 1.48v load passes P95/AOD/EVEREST/OCCT/Sandra/Benchmark testing.
Thanks for the template Camp, its very helpful to me starting from scratch :D :toast:
:D "New" DFI LanParty UT 790FX-M2R ~ 4/16/2008 "Beta" Bios... Released
WOW....2 Beta Bios in 2 days GO>> DFI >>>>>>>GO:shoot: :CTF: :bows:http://www.dfi.com.tw/Support/Downlo...FLAG=B&SITE=US
LOL, finally they're actually getting a move on as they should. ;)
Didn't I tell you that there's this bug? :p:Quote:
Major Reasons of Change:
1.Fixed “CPU Clock Ratio”can not select when use some Phenom CPU .
2.Increase CPU voltage control step by step.
3.Add CPU Voltage Item help string.
There's another with Special Voltage Add yet to resolve as well as temps.
Any testers?
Post full details including a WinRAR comparison with a previous BIOS please. :)
Gonna Flash Now Tye will save screenie from WinRar now and after for you:)
Hurry up :DQuote:
Originally Posted by Oese
http://valid.x86-secret.com/show_oc.php?id=347097
1.475v
Here ya go Tye:)Quote:
Originally Posted by KTE
whuuuuuhoooo :DQuote:
Originally Posted by Final8ty
ram is on the way.. i'm curious whether this would be possible with my chip...
Quote:
Originally Posted by Oese
Ahem/......I say old Boy! I should think so oli
Thanks m8, better this than a broken leg. :p: :up:Quote:
Originally Posted by Aussie FX
I'm afraid but can't test it, no more AM2/+ boards here, never happened to me, all my previous CPU's are running well, I tested Phenom 9500 and 5000BE, all booted fine, with my G.Skill and OEM memory, both 1 or 2 slot use. :shrug:Quote:
Originally Posted by KTE
Maximum volts applied was 113.07% when testing 3200MHz(HTT=200;HT=2000;NB=2000), I made a table on that 3200 test and realized that more volts didn't work, if fact only booted at 107.02%; 109.15% and 112%, NB-VID=AUTO in all tests, system always unstable.Quote:
Originally Posted by justapost
Well, if OCing can be considered Warranty void, then yes, I can say it's my fault not running at stock speed. :DQuote:
You plan to RMA that CPU or do you think it was your fault only? I mean both board and the chip are build for overclocking and you ran your cpu in specs at modest higher voltages.
:yepp: Nothing extreme here, never got it more than 113% for CPU;107% for NB, and 2.24v for MEM, in any scenario.
If, someone here get me one board to test, as Tye suggested, I will do it before RMA, any way I already contacted Alternate and explained what happened, I have the RMA number to do it, if no other choice, will be at least 2 weeks waiting, with all the stress that evolves.:nuts:
Thanks to all of you guys, for your support. :up:
Brother Esau , if you was here I would kiss ya:eek: .....(if you was a girl).....:up:
Bios flashed slicker-n-snot.......
Now, how hot is too hot?????
I know my TRUE is in good contact with the CPU, the heat pouring out of it is unreal. But load temps across the cores are in the high 40's to low 50's when crunching Seti with optimized clients, CPU running 2800mhz....
Ummmmm...... uh..... Ok you sexy beast just what did I do to get you so Hot and Bothered?:rofl: :hrhr:Quote:
Originally Posted by Slagathor
What volts?Quote:
Originally Posted by Slagathor
Default volts......
1.3 I do believe
I was scared witless for a second after the flash, cause I edited your command line into the autoexec that came with the 415, but I didnt get rid of:
"echo "The version of BIOS was inaccurate,"
echo "Please remove the floppy, download the right one and re-flash."
I was like:eek:, but it was all pretty white, so I figured I was safe, which I was....
Heres what I get with 2800mhz up to 2846mhz same settings;)
DFI LANPARTY UT 790FX-M2R (BIOS 4/15/2008 "Beta")
AMD Phenom 9850 Black Edition "B3"
Tuniq Tower 120
OCZ Reaper HPC (PC2-8500) 5-5-5-18 2X2GB
POWERCOLOR AX3870 X2 CROSSFIRE CATALYST 8.3
Auzentech XPlosion
Areca 1231 ML {Intel IOP 341} ~ 6 ~ 250gb Hitachi Sata II Raid 6 ~2~WD 74gb Raptors ~ Raid 0 ~
Plextor 750A
SilverStone OP1000
CM Stacker STC-T01
Code:>HT Link Control:
HT Link Width......................... - 16 bit
HT Frequency.......................... - 2GHZ MHz
IH Flow Control Mode.................. - Disabled
HT Link Tristate...................... - Disabled
2x LCLK Mode.......................... - Disabled
Unit Id Clumping...................... - Disabled
>CPU Feature:
CPU DID.............................. - 1
CPU FID.............................. - 0C
CPU-NB DID........................... - 1
CPU-NB FID........................... - 06
AMD CPU stepping..................... - P0
>DRAM Configuration:
MCT Memory Timing.................... - Manual
2T Mode.............................. - Auto
Cas Latency Time..................... - 5
Pre Charge Delay (tRAS).............. - 18
DRAM RAS# Precharge.................. - 5
DRAN RAS# to CAS# Delay.............. - 5
Bank to Bank Cmd (TRRD).............. - Auto
TRC.................................. - 23T
TRTP................................. - Auto
Write Recovery (TWR)................. - Auto
Write-Read Command (TWTR)............ - Auto
TRFC0................................ - 195ns
TRFC1................................ - 195ns
TRFC2................................ - 195ns
TRFC3................................ - 195ns
Trdrd................................ - Auto
TrwtT0............................... - Auto
Twrrd................................ - Auto
Twrwr................................ - Auto
CS/ODT Pin Fine Delay................ - Enabled
Bank Swizzle Mode.................... - Enabled
Auto Tweak Performance............... - Enabled
Optimal Performance Mode............. - Enabled
>ODC Control Mode:
DRAM Drivers Weak Mode.............. - Normal
Output Drivers Comp................. - Normal
>Channel A:
CPU On-die Termination.............. - 300 ohms +/- 20%
DQS Drive Strength.................. - 1.00x
Data Drive Strength................. - 1.00x
MEMCLK Drive Strength............... - 1.00x
Addr/Cmd Drive Strength............. - 1.50x
CS/ODT Drive Strength............... - 1.50x
CKE Drive Strenght.................. - 1.50x
>Channel B:
CPU On-die Termination.............. - 300 ohms +/- 20%
DQS Drive Strength.................. - 1.00x
Data Drive Strength................. - 1.00x
MEMCLK Drive Strength............... - 1.00x
Addr/Cmd Drive Strength............. - 1.50x
CS/ODT Drive Strength............... - 1.50x
CKE Drive Strenght.................. - 1.50x
>PWM Settings:
PWM Control.......................... - Enabled
CPU VID Control...................... - 1.2500v
CPU Vid Special Add.................. - Auto
CPU NB Vlotage Control............... - Auto
CPU NB Vid Special Add............... - Auto
DRAM Voltage Control................. - 1.80v
SB PLL 1.2V Voltage.................. - 1.20v
NB Core Voltage...................... - 1.250v
NB PCI-E Voltage..................... - 1.120v
NB HT Voltage........................ - 1.270v
Genie BIOS Settings:
Timing Mode.......................... - Manual
Memory Clock value or Limit.......... - DDR 1066
PCIE 3,4 State....................... - Auto
PCIE 2 State......................... - x2
CPU TLB Cache Fix.................... - Disabled
AMD K8 Cool & Quiet control.......... - Disabled
CPU Clock Ratio...................... - Auto
Spread Spectrum...................... - Disabled
CPU Host/HTT Clock................... - 200mhz
CPU Host/HTT Boot Up Clock........... - 200mhz
CPU Host/HTT Adjustment Gap.......... - 5mhz
PCIE Clock........................... - 100mhz