oniL,here you go.and remember this is with 8gigs of ram so you might not need the same volts.MCH? might be a little high but it's what got it stable for me. http://i44.tinypic.com/1zclguq.jpg http://i43.tinypic.com/30uwxms.jpghttp://i40.tinypic.com/20u7lok.jpghttp://i43.tinypic.com/20iw7q0.jpghttp://i42.tinypic.com/5zdu8j.jpg
@ radaja
it looks very good but your motherboard temperature @ 15 ° C provides for me to open windows and cold Roomtemp.with 1.42 V-core is not the temps below 45 ° C to hold.
but no matter still looks good.
I wasn't sure what you ment by, "Make Value to 0.68-0.70 in ET6" for MHC Ref?Quote:
Originally Posted by BuGjAE
please forgive me if i tell you what you already know, i think, just like you already did 533fsb, you will have to try it first to see if the system with the existing ram kit can handle booting 550fsb and then it seems to pass memtest fine?, then there's a good chance that the system will be able to run stable at 550fsb.Quote:
Originally Posted by BuGjAE
but if you find that it's a little harder to do it, i would suggest you might want to first try with the Standard mode and set 5-5-5-15 and also leave tRRD-tWTR-tWR-tRFC-tRTP settings to Auto and set tRD value in bios to 11-12, then after you have a stable overclock check back to all these bios settings.
i would like to suggest you check out the threads a bit if you haven't.Quote:
Originally Posted by Jsunn
because if you looking for step by step hand holding answers then it may takes quite a time to wait, but it's all up to you.
siyah,dont quite understand what your saying.but concerning my temps,i have a 4500rpm fan mounted on my NB. another one on the mem(even though it not needed with this set).two 1900rpm fans on my true in push / pull.1 vantec tornado 4800rpm in front intake which sucks air from the dryer vent hose thats hooked up to my airconditioner.when the air conditioner kicks in the motherboard temps drop to about 12c -13c. where as the cpu temp will hover around 40c with prime95 and 54c with intelburntest,but when the air conditioner kicks off the temp are more like 19c-22c for the motherboard sensor and cpu the cpu sensor is around 47c for prime95 and 60 for IBT.heres a pic of the setup.and one at idle.mind you i have stuck sensors on my cpu,they dont go lower than 39c-27c. http://i41.tinypic.com/2db71pg.jpg http://i38.tinypic.com/34693kn.jpg
@ Jsunn
Set your Vtt to stock 1.2 then lower that MCH Ref to .68-.70 then raise your Vtt back to where you had it.
Then you will see .68-.70 in EasyTune instead of .76 which is the default %
Click Here>> EP45UD3P - Beta Bios ID: F7cQuote:
Originally Posted by ghost_recon88
Should work now. :)
Any updates for the EP45T UD3P Nelly ?
I have just purchased the Gigabyte GA-EP45T-UD3R DDR3 version to run on my QX9650 with Corsair 1800Mhz RAM.
Have been using the Asus Maximus Extreme that has been a hunk of crap with my QX so fingers crossed this Gigabyte thingy will be much better.
I will try to get some results once I get my NB water block.. (which are like Gold dust for these boards btw and had to order one all the way from Germany ;)
I have always used ASUS mobos b4 so Im sure it will be a nice learning curve or me.
I notice alot of people using the 'easy tune' utility on this thread. Is that what most people are using to OC rather than the BIOS or is it just to show volts etc etc???
@ radaja
Oh Man this is really sick and Crass simultaneously with an air conditioning to cool
Thanks for all of the help. The problem I was having is that I dont' know what depends on what with all of the different BIOS settings. I have read through this thread a number of times but I am still a bit overwhelmed.
Thanks for the help.
-J
Yep all the references depend on other settings and change if you change other settings.Quote:
Originally Posted by Jsunn
Like Dram voltage changes all of the memory references to 1/2 of the Dram voltage if left on auto.
The Cpu ref and MCH ref depend on the VTT, so like said above if you set the ref's with VTT at stock 1.2 then change the VTT ET6 will still show them as the same(as they would be with 1.2 VTT) even though they are altered
@pangingIII ,Thanks so much about yr recommended ,I haven't not much OC RAM exprience, just wana hear some opnion :) , I search all around about my ram Ocing and found
no info, 550 MHZ 1:1 I can boot up but not stabil with memtest or orthos even PL 11 and auto subtimming ,I 'll try later, anyway yr step to checking RAM stabil is so great appreciate!
so far I can go 538 MHZ 1:1
you may want to first save the existing configured CMOS to a profile in BIOS or save it as file in a USB pen drive.Quote:
Originally Posted by MaXThReAT
and try this next, change tRD value in bios on both Ch A and B setting from 8 to 7, and see if you can still booting to bios and then into Windows?
if you can, then retest for ram and overall stability again.
in the case that you like to tweak your memory timing in Windows and then take the values setting into BIOS,
here's an example of the memory timing values in Bios vs. Memset (or in Everest's Motherboard > Chipset)
as far as i can see, it's just like the owner of Memset program used to explain somewhere around these forum.
20-8 = 12
13-8 = 5
the tRTP value in BIOS is seems to always has the value with +2 in Windows.
this's the exactly memory timing values that i set in bios...
5-5-5-15 / (in the Advanced section) 5-5-12-70-5 / tRD 7 on both Ch A and B.
http://img243.imageshack.us/img243/3...4130023eo8.png
please also note that, you have a different hardware than mine, so you may want to disregard my voltage setting values that you see in ET6.
I notice alot of people using the 'easy tune' utility on this thread. Is that what most people are using to OC rather than the BIOS or is it just to show volts etc etc???
anything you see im doing wrong please let me know. oc 3.6ghz. if i try 3.8ghz with 1.4v blue screen, i really want to get 3.8-4.0ghz on my q9550e0
******Motherboard Intelligent Tweaker (M.I.T.)******
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio............................[ + 0.5 ]
CPU Frequency 4.0GHz............................[ 424 x 8.5 ]
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 424 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance.............................[Standard]
(G) MCH Frequency Latch.........................[ 333mhz]
System Memory Multipler.........................[ 2.00B]
Memory Frequency 800............................[ 848]
DRAM Timing Selectable..........................[ Manual]
CAS Latency Time................................[ 5]
tRCD............................................[ 5]
tRP.............................................[ 5]
tRAS............................................[ 15 ]
******Advanced Timing Control******
tRRD............................................[ Auto ]
tWTR............................................[ Auto ]
tWR.............................................[ Auto ]
tRFC............................................[ Auto ]
tRTP............................................[ Auto ]
Command Rate (cmd)..............................[ Auto ]
******Channel A Timing Settings******
Static tRead Value [ 10 ] ...............[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 10 ] ...............[ 9 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration...........................[ disabled ]
CPU Vcore [ 1.21250 ]...................[ 1.3625 ]
CPU Termination [ 1.20 ]...................[ 1.28 ]
CPU PLL [ 1.50 ]...................[ 1.59]
CPU Reference [ 0.760 ]...................[ 0.863 ]
MCH Core [ 1.100 ]...................[ 1.36]
MCH Reference [ 0.760 ]...................[ 0.820 ]
MCH/DRAM Refernce [ 0.900 ]...................[Auto ]
ICH I/O [ 1.500 ]...................[ 1.59]
ICH Core [ 1.100 ]...................[ 1.20]
DRAM Voltage [ 1.800 ]...................[ 2.10]
DRAM Termination [ 0.900 ]...................[Auto]
Channel A Ref [ 0.900 ]...................[ Auto]
Channel B Ref [ 0.900 ]...................[Auto]
i don' know about other people, but for myself, i always included ET6's voltage page when i take screenshot, it's mostly for my own voltage setting records. and it might be useful to mke them visible to other.Quote:
Originally Posted by Crazymilk
i use ET6 (to replace SetFSB) sometimes, like when i want to get above 600fsb in Windows or when i want to see how far a ram kit can overclock, i only use ET6 for something like this.
Click Here>> EP45TUD3P - Beta Bios ID: F4Quote:
Originally Posted by Leeghoofd
Note: This is for the DDR3 Motherboard.
On Tweaktown theirs F4a, so not sure if this is a newer version?
Great thread guys:up:
Just getting going on the GA-EP45-UD3R
Am running on air at the moment and have been suprised by
the low CPU temps Any one else noticed this?
Well, I seemed to have corrupted my registry from the multiple BSOD that I was getting trying to O/C. I had to reinstall Windows last night. :dammit:
Going to try again tonight.
-J :p:
Quote:
Originally Posted by Supershanks
What BIOS version you using m8? I have just got that mobo as well and gunna start soon.
Shoulda used system restore by booting from the dvd and then choosing repair my Computer, then system restore.
Good luck man!
Have you tried booting at stock or lower OC. It's not unusual to get lost user or can't find registry messages, which thankfully go away when oc is lowered.Quote:
Originally Posted by Jsunn
F5 mateQuote:
Originally Posted by Crazymilk
Hi Lsdmeasap how you doing :up: not seen you over here much until I clocked this thread :)
Ahh I'm aight! How bout you? I tend to mostly checkout this and the Water section, but I been here a good while now