Guide Thread

Printable View

Show 100 post(s) from this thread on one page

12-23-2007, 12:54 PM
dinos22

Quote:

Originally Posted by joe.denice

#2 pencil to those areas???

2B pencil yes
12-23-2007, 05:12 PM
varrius

Quote:

Originally Posted by shawn1998

Anyone running one of these boards upside down? I might get one to play with over the holidays, but it would have to go in my Lian-Li inverted.

Shawn

http://i48.photobucket.com/albums/f2...k/PICT0008.jpg
12-23-2007, 05:18 PM
shawn1998

Quote:

Originally Posted by varrius

http://i48.photobucket.com/albums/f2...k/PICT0008.jpg

Awesome, thanks!

Shawn
12-24-2007, 09:35 AM
Dede99

Nice rig there varrius, how about scores in 3dmark with those monsters in SLI :D
12-24-2007, 09:58 AM
billdavis

santa was good this year

im going to add this to a evga 780i

http://i107.photobucket.com/albums/m...6/DSC09835.jpg
12-24-2007, 11:43 AM
GAR

nice cpu
12-24-2007, 04:35 PM
Dede99

good luck with it :) but I will wait for the Q since QX is to expensive
12-24-2007, 04:47 PM
GAR

Quote:

Originally Posted by Dede99

good luck with it :) but I will wait for the Q since QX is to expensive

same, but the 7x multi is gonna suck for the q9550
12-24-2007, 05:44 PM
Aivas47a

I thought the 9550 was going to have a 8.5 multi? That's bad enough but 7 would really blow. :(
12-24-2007, 07:29 PM
RottenMutt

Quote:

Originally Posted by GAR

is anyone using occt ram test????

memtest 1.7 pases without problems, but occt fails.....any help would be appreciated, i have run into a couple of problems with this board so far, hope to get them fixed.

have you tried the built in vista memory checker. don't froget to switch it over to advanced. i don't like memtest86, it doesn't find memory errors very well.
12-24-2007, 10:47 PM
GAR

Quote:

Originally Posted by RottenMutt

have you tried the built in vista memory checker. don't froget to switch it over to advanced. i don't like memtest86, it doesn't find memory errors very well.

i got it to pass prime blend for over 4 hours, requires alot of voltage from the NB, 1.5+ to pass, all other voltages are either on the highest green, or the on first red.........so if ur running 4gb at high frequency you are going to need alot of voltage to pass.
12-25-2007, 08:46 PM
joe.denice

well the mod seemed to work out, what is a good software program that works on this board to monitor volts?
12-25-2007, 09:03 PM
DarthBeavis

putting 780i on triple 8800 gtx (water) with QX9650 on modifed Vapochill tomorrow guys . . .hope for good benches . . .
12-25-2007, 10:04 PM
GAR

Quote:

Originally Posted by DarthBeavis

putting 780i on triple 8800 gtx (water) with QX9650 on modifed Vapochill tomorrow guys . . .hope for good benches . . .

Very nice, look forward to your results.........

a good program to monitor temps is http://www.cpuid.com/hwmonitor.php :up:
12-25-2007, 10:07 PM
DarthBeavis

Quote:

Originally Posted by GAR

Very nice, look forward to your results.........

a good program to monitor temps is http://www.cpuid.com/hwmonitor.php :up:

problem with most programs is they suck at sub-zero temps . . .speedfan does work
12-26-2007, 04:06 AM
jas420221

Well... running @ 3.4Ghz 425 FSB, memory manually set at the ram's rated speed of 1066.
12-26-2007, 04:38 AM
Warboy

I wanna point out something in the Guru3D Review

Quote:

To fine-tune for stability you can change out the HTT Link Multipliers (1x to 5x), both for upstream and down stream, so that you do not push the Hyper Transport speed way out of stability while adjusting the base reference clocks.

Since when did Intel have Hyper Transport :rofl:
12-26-2007, 04:45 AM
jas420221

Quote:

Originally Posted by Warboy

I wanna point out something in the Guru3D Review

Since when did Intel have Hyper Transport :rofl:

:ROTF:

It is in there though!

Is that something that should be dropped to say 4x?
12-26-2007, 07:57 AM
joe.denice

Quote:

Originally Posted by mcoffey

Hey here's a question,

Just got my board the other day and noticed a springed coil sticking out the back of the board, connecting to one side of the MOSFET cooler hold down. First time I've ever seen that. At first I thought it was a flaw, but checked the pics on Newegg and can see that board has one also. What the heck is that for?

andyc

i saw that as well and pulled it out, though hopefully that didn't mess up the contact with the northbridge heatsink??
12-26-2007, 09:30 AM
GAR

nVidia chipsets use HTT to talk to the cpu, by lowering the multi to 4 and taking the HTT mhz to 300 you have a HTT of 1200, 300x4, stock is 200x5.......i have tested this and a bit of performance is gained by doing this....if you are benchmarking, every bit of extra is usefull.
12-26-2007, 09:54 AM
mele

Quote:

Originally Posted by GAR

nVidia chipsets use HTT to talk to the cpu, by lowering the multi to 4 and taking the HTT mhz to 300 you have a HTT of 1200, 300x4, stock is 200x5.......i have tested this and a bit of performance is gained by doing this....if you are benchmarking, every bit of extra is usefull.

I wonder if this would help me OC my CPU? I can boot @ 3.9Ghz but it's not stable no matter what voltage I use.
12-26-2007, 11:43 AM
shawn1998

The Areca ARC-1210 8X pci-e Raid card works just fine in the middle slot. Just thought I'd give you all some feedback. I just finished installing the board. No testing done just yet, but will post back when I do.

Shawn
12-26-2007, 11:56 AM
billdavis

hurry up!!

jk have fun

Show 100 post(s) from this thread on one page