Forward: official GIGA 965P-S3/DS3/DS4/DQ6 beta BIOS

Quick Q:
Anyone know if there is an issue with PCI 2.1 and the DS3?
I read a review somewhere saying that those devices will not work in the DS3 since they are "older?" PCI?

Only reason I worry is that my sound blaster x-fi card says under requirements available PCI 2.1 slot. Luckly this is the only pci card I will be using for now.

So first off is this true or only an issue on some of the boards? Secondly is there a fix?

I guess I will just wait to see in a few days once i get my ram.

Thanks...maybe the newer bios have fixed this.

Quote:

---

Originally Posted by vsamaco

Go to device manager from system. Under IDE ATA/Atapi controller, right click on primary ide channel (maybe multiple) for properties. Should be under advanced settings tab =>transfer mode.

---

Great, thanks alot.

i'm on the new bios for DS3 and there's no change in terms of OCing.......if anything it's a bit worse for Allendale....but considering DMA fix it's ok

they REALLY need to put the RAM dividers in for sub 1:1

i don't understand why they aren't doing it................

Quote:

---

Originally Posted by Chris583

Quick Q:
Anyone know if there is an issue with PCI 2.1 and the DS3?
I read a review somewhere saying that those devices will not work in the DS3 since they are "older?" PCI?

Only reason I worry is that my sound blaster x-fi card says under requirements available PCI 2.1 slot. Luckly this is the only pci card I will be using for now.

So first off is this true or only an issue on some of the boards? Secondly is there a fix?

I guess I will just wait to see in a few days once i get my ram.

Thanks...maybe the newer bios have fixed this.

---

My X-Fi sounds beautiful on my DS3. :) No worries.

Quote:

---

Originally Posted by Brahmzy

My X-Fi sounds beautiful on my DS3. :) No worries.

---

Xcellent :)
I'm much relieved

RAM OCing was farked

back to F3

F3=good :D

http://img184.imageshack.us/img184/3...superpipe5.jpg

Quote:

---

Originally Posted by dinos22

RAM OCing was farked

back to F3

---

ok you cant make a statement like that and NOT tell us why you say that.

Quote:

---

Originally Posted by Lestat

ok you cant make a statement like that and NOT tell us why you say that.

---

right, and F3 what??

:D

not too shaby

is that still stock volts? if so very nice:)

Is it possible to update DS3 Bios from usb stick using Q-Flash?

I looked in the manual and it only talks about floppy, and I dont have one.

http://www.gigabyte.com.tw/Support/M...flashBIOS.aspx

w/o os installed, floppy only way
w/ os installed, use @bios software

Quote:

---

Originally Posted by Lestat

:D

not too shaby

---

LOVE your results Lestat. I just pray that others including myself can do the same with RETAIL E6600!!

yeah, he's running an es, so retail is still up in the air on what they'll do.

VSMACO DQ6 users cant update whith @bios

Quote:

---

Originally Posted by vsamaco

http://www.gigabyte.com.tw/Support/M...flashBIOS.aspx

w/o os installed, floppy only way
w/ os installed, use @bios software

---

wait wait wait,,,

with os installed or without os installed it makes absolutely no difference. not when your talking about HOW to flash the bios.

use a usb stick. it works fine.
maybe because mine is seen as a floppy drive.

and if at all possible never ever flash your motherboard using an OS software. that is the best way to kill your motherboard. you cant imagine how many people come here with botched boards cuz something happened during the flash procedure using the OS, or they rebooted and it bombed.

i HIGHLY recommend that you do NOT use the windows @bios software to update the bios.

people will do what they will and disregard warnings. but i stand behind that statement.
dont flash using windows software.

Quote:

---

Originally Posted by Lestat

wait wait wait,,,

with os installed or without os installed it makes absolutely no difference. not when your talking about HOW to flash the bios.

use a usb stick. it works fine.
maybe because mine is seen as a floppy drive.

and if at all possible never ever flash your motherboard using an OS software. that is the best way to kill your motherboard. you cant imagine how many people come here with botched boards cuz something happened during the flash procedure using the OS, or they rebooted and it bombed.

i HIGHLY recommend that you do NOT use the windows @bios software to update the bios.

people will do what they will and disregard warnings. but i stand behind that statement.
dont flash using windows software.

---

I'm unable to get my board to boot from a USB drive. The same drive works in my laptop, but all 4 USB boot options don't work for me on the DS3. Any ideas? Do i need to format it differently for this board?

Quote:

---

Originally Posted by toddm27

is that still stock volts? if so very nice:)

---

oh gawd no. but i sure wish that was stock volts.

for being a low wattage chip this things sure get warm when you start getting close to 1.4v even on water.
but then again with the heat the way it is and no A/C in my PC room...
im about ready to sit my RAD on a container of Dry Ice!!

Quote:

---

Originally Posted by Lestat

oh gawd no. but i sure wish that was stock volts.

for being a low wattage chip this things sure get warm when you start getting close to 1.4v even on water.
but then again with the heat the way it is and no A/C in my PC room...
im about ready to sit my RAD on a container of Dry Ice!!

---

:p: :D wishfull thinking, we'll see how some of the retail chips start doing soon hopefully:toast:

Quote:

---

Originally Posted by Lestat

oh gawd no. but i sure wish that was stock volts.

for being a low wattage chip this things sure get warm when you start getting close to 1.4v even on water.
but then again with the heat the way it is and no A/C in my PC room...
im about ready to sit my RAD on a container of Dry Ice!!

---

The heat seems to be a problem on all of the conroe boards at the moment, especially with vcore on the rise..

Quote:

---

Originally Posted by BottomsUp

I'm unable to get my board to boot from a USB drive. The same drive works in my laptop, but all 4 USB boot options don't work for me on the DS3. Any ideas? Do i need to format it differently for this board?

---

hhmm mine is distinctly seen as a floppy drive so i imagine thats why it works for me i guess.

you can also use a USB floppy so. again thats why i imagine it works for me.

Sry if this is late lol... but i am very happy to see the raid issue solved. So with the F4c bios the issue has been solved? nothing else needed just that bios or any other drivers ?

thx

:banana:

Quote:

---

Originally Posted by BottomsUp

I'm unable to get my board to boot from a USB drive. The same drive works in my laptop, but all 4 USB boot options don't work for me on the DS3. Any ideas? Do i need to format it differently for this board?

---

The USB drive depending how its formatted might appear in the Hard Drive section. Plug it in and go into the bios and look at the Hard Drive boot order. If its in the list just change it to the first device (usb stick needs to be setup as a dos boot disk).

Quote:

---

Originally Posted by hopester

The USB drive depending how its formatted might appear in the Hard Drive section. Plug it in and go into the bios and look at the Hard Drive boot order. If its in the list just change it to the first device (usb stick needs to be setup as a dos boot disk).

---

no no no

and setting up a usb stick as a dos boot disk can be a pain in the a$$ becaus only certain usb drives are capable of doing so.

go into the bios and use the F8 option for the QBios.
thats all you do not need to boot to a dos floppy and flash that way.
that is 100% ok though you can do that to. there is nothing wrong with that.
but the usb drive is used in the Qbios. not dos.

One thing I noticed as I started to overclock is that the northbridge is HOT!

Even at only 300fsb x 8 with the e6400 and 30 minutes of priming, it's very warm, the entire heatsink is.

I'm using one of these coolermaster sinks on there with AS5.. the entire aluminum portion of the sink is quite warm, at least I know the sink is doing it's job well... northbridge temp reads 42 degrees after 20 minutes of priming and seems to stablize there at 300fsb at least... now at 325.

http://www.xoxide.com/cooler-master-blue-ice-2.html

I shudder at the idea of what that poor northbridge is going through for those using the stock heatsink, even with a fan, trying to push that fsb above 450 with it. Even the southbridge is warm enough where I may consider replacing it with something else.