Printable View
Its gotta be the MOBO
I have cleared Cmos , done the battery removal thing you name it.
removed from case
swapped CPUs
swapped GPUs
swapped Power supplies
tried every ram slot dual and single stick configs
NO BOOT
put e8400 into my P5W 975 and it boots
IMO the mobo is the problem.
I can run the P5W for now until the P5Q comes back
anyone have any other suggestions???? or ideas??? beside RMA the mobo???
ah i know..Quote:
Originally Posted by iboomalot
the first test board i had..
had a issue with my raptor x 150gb..
take that out.. infact run no hdd's on the sata port..
try that
I had the hard drive disconnected
last ditch effort removed all jumpers
put mobo to no OV
put security jumper to default
cleared CMOS and removed battery
plugged in ZM-1000-HP with both 4pins to the CPU and it booted.
put system back together with one 4pin and still booted
now the system won't load windows gets 1/2 way into drivers and crashes
Thanks for the helpfull suggestions
Most likely realtemp is correct as it has the tjmax of 95, which explains why coretemp is 10c off.Quote:
Originally Posted by Chura
Leave at first all voltage options on AUTO (except Vcore and Ram voltage)Quote:
Originally Posted by R@ptor =]]
NB 1.2 will be enough
FSB Term Voltage : 1.3
CPU PLL : 1.6
But it can all be different with each CPU... try one setting at a time, if it posts test it thoroughly then adjust another setting... if you set them all at one time you won't find the bad setting if it doesn't post...
For the ram better go with 1:1 then so 450FSB will provide 900Mhz ram...
Reinstall the OS completely, it wil load different ( too old drivers ) and will prolly crash... a complete format is required here or to adjust some setting in the biosQuote:
Originally Posted by iboomalot
What did you mean you set mobo to no OV ( did you set that jumper to OV ? )
Quote:
Originally Posted by Leeghoofd
In case anyone wants to know :
The P5Q-Pro doesn't have any backplates to prevent board warping, so you'll have to buy a separate backplate.
You went for the pro then Jupiler... hope it works out for ya sir
Due to numerous posts on this and other threads can everybody with this board make this check plz and PM me about results or just add them here
PLZ SET YA NB VOLTAGE TO 1.3 AND ADVISE ME IF IT POSTS YES OR NO... I have tested this at numerous FSB/RAM/CPU combos and each time I set 1.3 in bios, it results in a NO POST... higher or lower is fine on my board... 1.3NB V not...
Thx in advance Leeg
Well,
it's the only one my reseller could find and which he had in stock.
I took one with me for testing, but I'm not sure if I'm gonna try it.
There's also only 1 bios version available, and seeing that the first initial release for the deluxe seemed to have problems (which have been resolved with new Alpha releases), I'm kinda worried running into the same problems as you guys had in the beginning.
sorry guys,
I have a dfi dk p35 with a raid0 on ich9r
On monday i will receive a p5q deluxe (ich10r), I will lost my raid0?
thanks
There's a 0505 Jupiler look for PMP's post but no idea what's shipped on the board...
Edited : saw 0506 on Asus FTP (prolly shiped bios)
Hmm so there are two types of these boards, good and bad ones :(
I Think that I´m going to check NB heatsinks contact.
Can you post your bios settings for that? My maximum is 530MHz FSB with 1.56V NB :(Quote:
Originally Posted by jozzy
2 types ? you mean other revisions already or what do you base your claim on BuldogPOQuote:
Originally Posted by BulldogPO
Does this board support celeron 347 with latest bios? I've tried, but no boot whatsoever. All core 2 cpu's tested so far works fine
The deluxe is $239 here in Sydney and $258 delivered aus wide . My 790i just decided it wont boot so Im seriously looking at getting one of these.Quote:
Originally Posted by MomijiTMO
:shrug:
Too bad to hear mate, secondly the P5Q3 Dlx (DDR3) is not yet up to the little sis DDR2 level, but more than sufficient clocks for most users (500+) hope this board will bring ya more joyQuote:
Originally Posted by aussie-revhead
Yeah mate thanks , my rig1 is getting less and less use with gaming done on rig2 coz at least its reliable .
:rolleyes:
Play with FSB Voltage, CPU GTL, NB Voltage, NB GTL and CPU / NB Clock Skew!Quote:
Originally Posted by BulldogPO
my board need first time 1.58v NB voltage for 600FSB, now can i boot 600FSB with
1.42v in Bios (1.39-1.40v real) ;)
my Settings:
FSB @ 1.24v
CPU GTL @ 0.63 (both!)
VDimm @ 2.40v
NB @ 1.42v
NB GTL @ 0.55
SB @ 1.10v
PCIe @ 1.50v
CPU Clock Skew @ 400ps
NB Clock Skew @ 200ps
Those stable settings Chris ? for 600/1200 prime ? might give it a go again then :) I usually set AUTO at first till it posts, then I back down NB voltage... I needed 1.5NB for the Small FFT's run 600/1200
BuldogPO has got the P5Q3 Dlx , no idea if it goes for him ( sure not ram voltage )
No its not stable, i think my CPU is max stable @ 570-580FSB (on P35 Chipset 515FSB :rofl: ) :)
This board has bad mojo. I finally got stable with 4 gigs of Cellshock @ 425MHz, 400 FSB Strap @ 1133MHz 5-5-5-15-42 yesterday, prime ran for a little over 4 hours. I came home from work this morning turned on my computer and it booted fine and then went into BIOS just to check my settings. I then exited the BIOS without making any changes and for no reason that I can think of the computer hard boots and refuses to load. It just sat theere running without loading the BIOS. These were my settings:
CPU Ratio: 7.5
FSB: 425MHz
PCIE: 101
FSB Strap 400
DDR2-1133MHz @ 5-5-5-15-42 the rest Auto
DRAM Static Rd: Disabled
DRAM Rd Training: Auto
Memory OC Charger: Auto
Ai Clock Twister: Moderate
PL: 7
All Pull-ins: Disabled
CPU Voltage: Auto
CPU GTL's: Auto
CPU PLL: 1.50V
FSB Term: 1.16V
DRAM: 2.14V
NB Voltage: 1.34V
NB GTL: 0.67
SB: 1.10V
PCIE: 1.50V
Load-Line: Auto
NB/CPU Clock Skew: Auto
After I rebooted it reverted back to stock settings like it was recovering from a bad overclock even though I had no indication from Prime that anything was wrong.
For some reason certain voltages @ or above 1.30V on the NB make this board flaky. I'm going to run my NB voltages as low as possible running my 4 gigs @ 1066MHz and then work my way back up again to see if I really need voltages above 1.3V on my NB.
Anyway......
Touge - thats de-ja-vou for me mate and its comments like yours that has me deeply concerned about buying one of these.
:shakes:
sorry guys,
I have a dfi dk p35 with a raid0 on ich9r
On monday i will receive a p5q deluxe (ich10r), I will lost my raid0?
thanks
Quote:
Originally Posted by Leeghoofd
my new p5q is 0506
:shrug:Quote:
Originally Posted by aussie-revhead
Yeah, I don't know what to say. I'm priming 1066MHz 400FSB @ 1.24V on the NB and everything seems normal so far. Once I get it to where it fails I will bumo it up .02V and start pushing the FSB and see what happens. I hope there's another BIOS out soon. I could just be memory compatibility issues, who knows....
Prime Blend ? I prefer to use OCCT 2H ram test to verify the settings... might be ya PL is also a tad too low for those speeds, NB voltage to low for those settings, TRFC... one dimm capping out,...could be some many things...Quote:
Originally Posted by TouGe
@ Leeghoofd
Prime Small FFTs seems to be no problem with 600FSB @ 1.42v NB voltage...
http://www.abload.de/img/600fsb0kh.png
I saw someone else made the swap and their raid0 array survived with a driver update.Quote:
Originally Posted by diablos
:up:
Chri$ch: what is your settings in bios? It's an amazing FSB you get. I've currently writing a review of this board, and have not so much more time to tweak and search for the best settings, so you would help me alot if you came with some tips. :)
I guys.
I Ricieved my P5Q Deluxe yesterday... everything on AIR
After several minutes, having connected board achieve this result
http://valid.x86-secret.com/ccpuz.ph...5519&nocache=1
http://valid.x86-secret.com/show_oc.php?id=375519
Regards
Thanks for the help man!Quote:
Originally Posted by Leeghoofd
1.6 for cpu pll it's not much to 450fsb??
900mhz for the ram is very little, I wanted a higher frequency :(
Anyone having problems with crucial on this board??
I'm afraid to happen with the same has happened with x38! :rofl: :rofl:
these settings should allow it to post and be stable for sure, if the CPU doesn't need it better for you and back down...Quote:
Originally Posted by R@ptor =]]
Think I've found my 24/7 settings for the E8500... 1.3125 in Bios set for Vcore drop to a nice steady 1.28 under load...(again a gain in comparison with the P5K Dlx where I needed 1.29 to be stable)
http://users.pandora.be/OAP/P5QDlx/E8500247.JPG
Yes, Prime Blend. I use OCCT as well but mostly Prime Blend if I really want to know I am stable long term and, so far, I am 7.5 hours stable @ 1.24V 400FSB Strap/1066MHz. I will test 1.22V when I get home this morning.Quote:
Originally Posted by Leeghoofd
I have tested each 2x1GB kit and each set was able to reach 450FSB. They passed MemTestPro but failed Prime95.
I'm sure if I raised the PL I could pass at a lower NB voltage, that is a given, but with Ai Clock Twister already set to moderate I don't want to lose anymore performance if I can help it. I will keep testing until I figure this out....
very very nice ;) ,can't wait till MondayQuote:
Originally Posted by Crazy Inside
I've come to the conclusion that I'm doing something wrong here . No matter what I try I cannot get a POST over 450 fsb , 450 runs prime fine and 460 , 475 , 500 = no POST . Using the same X3360 and a 780i I was getting into vista @ 3.992ghz but no higher and prime wouldn't even run , it ran at 3.88ghz prime stable for about 5 days before the board died . I'm using latest bios from Asus site , any help would be great .
Great result, what settings in BIOS did you have?Quote:
Originally Posted by Crazy Inside
Plz fill in the template and list all ya hardware plzQuote:
Originally Posted by hellcamino
ASUS P5Q DLX Template :
JumperFree Configuration Settings
AI Overclock tuner: manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: AUTO
FSB Frequency: 450
PCI-E Frequency: 100
DRAM Frequency: 900-1081
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information :
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information :
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO
Common Performance Level AUTO
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.36875-1.4
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.5-1.6
FSB Termination Voltage: 1.3-1.4
DRAM Voltage: 2.26
NB Voltage: 1.2-1.5
NB GTL Reference: AUTO
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.5
Load Line Calibration: enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal
Advance CPU Settings
CPU Ratio Setting: Manual @ 8.5
CPU VID: Default (don't have this option )
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled ( don't have this one )
CPU TM Function: Enabled
Execute Disable Bit: Disabled
How are you guys getting your PL level in windows? I cannot get memset3.5 to work on this motherboard. I get a "NOT FOR THIS CHIPSET" error.
Does someone have a new version of memset or something?
As for my overclocks, this is much better than my P5K Premium or Maximus Formula.
P5K Premium has better PL levels and memory performance IMO.
Current overclock, completely stable (PRIME95, blend,small,large). I can get the same settings on both my P5K Premium and Maximus with lowest voltages on all three. The maximus however would not let me run my 4x1GB KingstonHyperX 8500 @ 1066, the P5K & P5Q not a problem. Also notice that I'm running at the lowest voltages for every section, I was in fact able to boot in Vista and run benches @ 550FSB with a voltage bump only on the RAM @ 1.9.
8400@4G
JumperFree Configuration Settings
AI Overclock tuner: manual
CPU Ratio Setting: AUTO
FSB Strap to North Bridge: 333
FSB Frequency: 444
PCI-E Frequency: 100
DRAM Frequency: 1067
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: AUTO
DRAM Static Read Control: AUTO
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: MANUAL
Common Performance Level 08
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.3375
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.50
FSB Termination Voltage: 1.10
DRAM Voltage: 1.80
NB Voltage: 1.10
NB GTL Reference: AUTO
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.50
Load Line Calibration: AUTO
CPU Spread Spectrum: enabled
PCIE Spread Spectrum: enabled
CPU Clock Skew : AUTO
NB Clock Skew : AUTO
Advance CPU Settings
CPU Ratio Setting: AUTO
C1E Suppport: ENABLED
Max CPUID Value Limit: DISABLED
Intel® Virtualization Tech: ENABLED
Vanderpool Technology: ENABLED
CPU TM Function: ENABLED
Execute Disable Bit: ENABLED
You are on 0702 Bios I hopeQuote:
Originally Posted by hellcamino
Alpha bios causes puckering of back door...How close to full build are they ? Do they appear to be reliable and stable ?
Version 3.5 works fine here on XP PRO and XP PRO 64, you on Vista ?Quote:
Originally Posted by stepinrazor
Pm Hellcamino
Memtest 3.5 is working fine in vista 32b.
This chipset is awesome, 500fsb with mems 5:6 1200 @ only 1.16vNB, blend stable. Still cant get to 600fsb but i've found my 24/7 settings :)
This is stable?? :shocked: :shocked::shocked:
can you test a 450fsb and diferent frequency of 900mhz for me??? :p: :D
Here it is, 8.5x500 1.16vNB:
http://i30.tinypic.com/2woyqer.jpg
What multiplier do you want me to use in the 450fsb test?
8x mate! :p:
more frequency than 900mhz to memorys plz!
thanks!
I received mine yesterday and its dead today :( , i was trying very hard for max fsb for validation and a quick aquamark bench E8400 under Dice at 602 FSB and 8800Ultra Under Dice 902/2248Mhz , then bum it crashed and never posted again , back to RMA on monday asap.
Last Pictures taken of the casualty of subsero temps :(
http://i157.photobucket.com/albums/t...7_06150001.jpg
http://i157.photobucket.com/albums/t...7_06150002.jpg
R.I.P............................................. .................................................. .................................................. ......................
450fsb 1:1 can't get lower than PL 10 at least with this settings, other than that no boot. 450fsb 5:6 is easy with PL 7.Quote:
Originally Posted by R@ptor =]]
Wow...thanks a lot mate!
Update my result with watercooling again :)
wtf...that's just messed up.Quote:
Originally Posted by ]siNNer[
I knew before ordering this that PL would be worse than with my DFI...but that's just terrible...
I guess i'll see how things are for 2:3 once i get mine, as that's likely what i'll be running.
1:1 is stuck to pretty high PL, it's better to use other dividers...
I did the testing a few pages before will sum it up again :
400FSB and Ram at 800Mhz -- Bios sets 13 perf level at AUTO setting -- Lowest manual is 9 (8 doesn't post)
400FSB and Ram at 1003Mhz -- Bios sets 10 perf level at AUTO setting -- Lowest manual is 7
400FSB and Ram at 1066Mhz -- Bios sets 9 perf level at AUTO setting -- Lowest manual is 7
450FSB and Ram at 900Mhz -- Bios sets 13 perf level at AUTO setting -- Lowest manual is 10
450FSB and Ram at 1081Mhz -- Bios sets 10 perf level at AUTO setting -- Lowest manual is 8
500FSB and Ram at 1200Mhz -- Bios sets 13 Perf level at AUTO setting -- Lowest manual is 10
600FSB and ram at 1200Mhz -- Bios sets 13 perf level at AUTO setting -- Lowest manual is 11 (though RAM not stable at all)
At the moment this board needs some higher PL than P35 and X38/48 to remain stable... Don't forget the board is only a few weeks old and future biosses will hopefully bring some more performance and ram compatability...
I went ahead and ran prime blend over night while I was at work using the following settings:
CPU Ratio: 7.0
FSB: 425MHz
PCI-e: 101
FSB Strap: 400
DRAM Freq: DDR2-1133MHz
5-5-5-15-3-40 (The rest AUTO)
DRAM Static Rd: Enabled
DRAM Rd Training: AUTO
Mem OC Charger: Auto
Ai Clock Twister: Moderate
Performance Lvl: 7
Pull-ins: Disabled
CPU Voltage: Auto
CPU GTL (0/2): 0.63
CPU GTL (1/3): 0.63
CPU PLL: 1.50V
FSB Term: 1.16V
DRAM Voltage: 2.14V
NB Voltage: 1.26V
NB GTL: 0.67
SB Voltage: 1.10V
PCIE SATA: 1.50V
Load Line: Auto
NB/CPU Clock Skew: Auto
and it passed 12 hours and was still running until I turned it off. I am terribly confused because in order for me to do the same with my Maximus Formula it took an nbv of 1.58-1.61V while here it only takes 1.26V? Huh.... I understand that the NB is now 65nm and that they also added better power regulation to the P45 but I wasn't expecting this much of a gain. Huh, again...
So I went ahead and shut the computer down for about 30 minutes and then rebooted, entered BIOS, exited BIOS and there was no issues whatsoever. It seems to be stable but as soon as I try 1.30V it fails to boot as well as at 1.34V. Huh again, I guess.....All is well:up:
I've reached the same conclusion, 1:1 only brings trouble, best to stick to other divider when possible.
In my setup I can use PL 8 with those settings and 1.16vNB as I said before. Here's my settings:Quote:
Originally Posted by Leeghoofd
Quote:
JumperFree Configuration Settings
AI Overclock tuner: manual
CPU Ratio Setting: 9
FSB Strap to North Bridge: Auto
FSB Frequency: 500
PCI-E Frequency: 101
DRAM Frequency: 1200
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : 5
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information :
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information :
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disable
MEM. OC Charger: Enable
AI Clock Twister: AUTO
AI Transaction Booster: Manual
Common Performance Level [8]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.44375
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.5
FSB Termination Voltage: 1.1
DRAM Voltage: 2.1
NB Voltage: 1.16
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
Advance CPU Setting
CPU Ratio Setting: Auto
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
Sinner can you run Everest cache and memory benchmark at those settings please?
Thanks :) That'll probably be my exact configuration when the board and the OCZ arrive here. Damn you have pretty good BW over there :up:
Could those of you who have already received their P5Q Deluxe please post their revision (and possibly, if their board was made in China or in Taiwan)?
So far, I'm only aware of 1.03G, maybe there are others?
It would be great if this information could also be put into the first post, to makle this thread a proper resource of information...
lolQuote:
Originally Posted by Crazy Inside
Congrat :shakes:
max FSB
http://valid.x86-secret.com/cache/screenshot/375559.png
http://valid.x86-secret.com/show_oc.php?id=375559
and 600FSB 1:1 (PL10) Everest cache and memory benchmark
http://www.abload.de/img/everest01ciq.png
anyone here with the P5Q3-Deluxe? I'm looking at one, and can pick it up today with some cheap, but nice Patriot DDR31333 7/7/718.
That's just incredible. Would be great if you could fill the template and share those settings :up:Quote:
Originally Posted by Chri$ch
:)
Code:JumperFree Configuration Settings
AI Overclock tuner: manual
CPU Ratio Setting: x
FSB Strap to North Bridge: Auto
FSB Frequency: 600
PCI-E Frequency: 101
DRAM Frequency: 1200
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : 5
Row Refresh Cycle Time: AUTO
Write Recovery Time: 45
Read to Precharge Time: AUTO
2nd Information :
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information :
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disable
MEM. OC Charger: Enable
AI Clock Twister: AUTO
AI Transaction Booster: Manual
Common Performance Level [10]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.xx
CPU GTL Voltage Reference (0/2): 0.63
CPU GTL Voltage Reference (1/3): 0.63
CPU PLL Voltage: 1.52
FSB Termination Voltage: 1.26
DRAM Voltage: 2.42
NB Voltage: 1.52
NB GTL Reference: 0.55
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.50
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : delay 400ps
NB Clock Skew : delay 200ps
Can't boot with those settings, don't know if is CPU wall or something else :confused:
try lower Performance Level (12 or 13) and play with CPU / NB GTLs, i think it is different at each system ;)
anyone found any good, easily accessible voltage read points for these boards?
:up:Quote:
Originally Posted by Pyr0
http://www.abload.de/img/vdimmuiu.jpg
http://www.abload.de/img/vnboffl.jpg
http://www.abload.de/img/vpllvfsbn5f.jpg
Source Awardfabrik
I can boot too but it's nowhere stable here , can't even complete a SuperPI 32Mb at PL 8... Small FFT's no issue, but I need PL 10 to be fully blend stable...Quote:
Originally Posted by ]siNNer[
See post#449, 8.5x500 is 1H blend stable.
My day setting is 8.5x500, while 9x500 over night. :D
:explode2: Room temp is 15ºC hotter during day :explode2:
excellent, thanks :up:Quote:
Originally Posted by Chri$ch
Maybe a small note, not directly related to the Deluxe version, but anyway.
I decided to install the P5Q-Pro (wasn't quite sure to try it or not), just to see how it would perform, specially for my X3350.
It looks like some options are left out in the bios, compared to the Deluxe version.
The following options are NOT available in the bios of the P5Q-Pro (important regarding overclocking, IMO) :
CPU GTL Reference (0/2)
CPU GTL Reference (1/3)
NB GTL Reference
NB Clock Skew
CPU Clock Skew
Kinda disappointed not having these options in the BIOS. :down:
The good part is that I installed my X3350, which couldn't run at 450*8 on the DFI DK-P35 / 2x DFI UT-P35 (not below 1.61 NBCore on one of them anyway), with only 1.24V NBCore on the P5Q-Pro.
Quote:
Originally Posted by Jupiler
I guess some of those were also missing from initial bios on the Deluxe. Is the bios 0702 available for the P5Q Pro?
Mine is the 1.03 version made in Taiwan.Quote:
Originally Posted by crishan
The same here. I can't believe the performance diffence between the x48 and P45. The P45 is what the x48 should have been.Quote:
Originally Posted by Jupiler
453 is all I can get out of my X3360 even with multi dropped to 6 , 450 is prime stable and anything over 453 won't post . How is everyone else doing with xeons in this board ?
480x8 is OCCT stable with my X3350. That is the same max stable overclock I got with this chip on P5E3 Premium.Quote:
Originally Posted by hellcamino
No store received the mobo yet in Brazil :(
But I still want to know if the tracers (best batch [double side chips] and pc6400) are having problem with this mobo...anyone?? :p:
You tried with 1-2 sticks only ?Quote:
Originally Posted by hellcamino
I tried with 2 and 4 with no discernible change and I switched pairs as well . Should I be disabling load line calibration ?
What voltage is set for Vcore ? how much Vcore do you need for 3.6Ghz ? Normally with some tweaking think 470ish could be possible but could well be your CPU does need excessive voltage to get that high.. or some nice GTL tweaking...
Quote:
Originally Posted by Leeghoofd
With vcore set to 1.36875 it idles about 1.52 with load line enabled and ramps to about 1.368v under load . I think it will run with a bit less for it's current 450x8.5 but as I have as yet to get it to post above 453 with as much as 1.425v .
R@ptor
My mate has got 2x1gb 6400 Tracer and no problems.Anyway not all double-sided Tracers 6400 were D9GMH chips,only some of them.About year ago Crucial stopped production of D9GMH/GKX for sure ;)
Now you can get Crucial D9GMH/GKX only on Ebay,or used from users :D
It was the Damn RAID Card. I have an old IDE Hard Drive that I need to use in my system. I couldn't use any of the onboard IDE's because I have 2 IDE DVD Burners. So I installed an PCI RAID Card which supports up to 4 additional IDE drives.Quote:
Originally Posted by Leeghoofd
As soon as I disconnected the IDE Drive from the RAID Card - Voila - PC posted and booted up just fine.
Can confirm:
OCZ Platinum Edition 4GB (2X2GB) Dual Channel PC2-8000 1000MHz: Works
I'll get some CPU-Z Screens on stock and attach back here. Will start OC'ing in a day or two.
IDLE temperature was running 39 - 41 (Real Temp) - Does that sound about right?
Thanks!
Did anybody try max. FSB with e7200? ... I have fsb wall at 510fsb on Commando (on air) and with P5QDlx it is 510fsb, too :(... no more with any other settings... to 510fsb it needs only vFSB 1.16V and vNB 1.2V.... Bios 0702...
Quote:
Originally Posted by LUCI5R
the kit of memories that you purchased this was here:
http://www.newegg.com/Product/Produc...82E16820227280
Thanks,
Just curious i think someone already asked this. Is the P5Q-dlx wifi any different performance wise than the p5q-dlx
Got a question for the experts :
Is there someone who knows how to mod bios', who can have a look into the P5Q-Pro 0506 bios, and see if the GTL tweaks are hidden, and can be enabled?
I used an AMI bios editor to check the bios, but I don't know if the program can check for any hidden features in a bios.
Yes! That's the one. $91, Free Shipping at that time. It's gone up a bit in price/shipping now I see.Quote:
Originally Posted by Gustao_Surf
Works absolutely awesome out of the box in my P5Q Deluxe. Recognized immediately.
Okay mate, thanks for the help!Quote:
Originally Posted by 71proste
i will buy this mobo, And I hope that any problems happen, as happened with the chipset x38 :(
Ordered one of these this afternoon, tho I won't get to play with it til the w-end.
Hoping for atleast 500mhz stable from my Q9450 since I can run 1mb Super-Pi at 490mhz in my IP35 Pro's.
Considering changing my P5K Premium for the P5Q Deluxe and I'm concerned that I'll lose the use of some sata ports using my 8800gts gpu. Can anyone confirm this ?
with my 9800gx2 the only port i can't use is the vertical one, all the others are easily available. :)Quote:
Originally Posted by colt1911
my p5Q-d arrives by the end of this week :)
anyone have any issues setting up 8GB of ram with this bad boy?
Some 3D action, system in sig:
http://i29.tinypic.com/6z22dg.jpg
isnt the one with wifi the P5Q3 Deluxe? (so its the DDR3 version)Quote:
Originally Posted by duke8989
No supplied WiFi w/ P5Q-D.Quote:
Originally Posted by duke8989
Is the 8800GTS that long? If your concerned just buy an elbowed SATA cord that is orientated in the correct position. I had one from my old RAID card and it works fine with my GX2.Quote:
Originally Posted by colt1911
With an 8800GTX :Quote:
Originally Posted by colt1911
http://users.pandora.be/OAP/P5QDlx/P5QDlx%20015.jpg
http://users.pandora.be/OAP/P5QDlx/8Gb400-1066blend.JPGQuote:
Originally Posted by Rise
Interested in this board, some of the early reviews suggested the performance could have been better. Has it improved with later bios(s) ?
If 600FSB is ya thing with wolfies yes things have improved, also we are seeing 500FSB quad action... just make sure you flash to 0610 or 0702 bios
Thanks appreciate the info and help.Quote:
Originally Posted by Leeghoofd