Printable View
My Q6600....
Q6600 G0 | L725B057 | 3608mhz | 1.352V | Liquid |
http://img75.imageshack.us/img75/445...4368fu9.th.jpg
http://img169.imageshack.us/img169/2...5578ia7.th.jpg
Q6600 G0 | L725B057 | 3708mhz | 1.40V | Liquid |
http://img241.imageshack.us/img241/7...140vnk5.th.jpg
http://img411.imageshack.us/img411/6...140vzm8.th.jpg
By;)
I asked for that:DQuote:
You mean a A v B war.
RLM
OK, this thread has too many different opinions in it.I want a Q6600 for My GA-965P-DS3 REV 1.0 + TITAN AMANDA with AS5, but I am not very sure if I should go for a B3 or G0, nor did I understand how to find out if it is B3 or G0 on the box...I will buy from retailer with no shipping.So, B3 or G0?I have read 16 pages with not so ver important info...And can anyone tell me what this means? BX80562Q6600
It's what comes after 'BX80562Q6600', which is important.Quote:
OK, this thread has too many different opinions in it.I want a Q6600 for My GA-965P-DS3 REV 1.0 + TITAN AMANDA with AS5, but I am not very sure if I should go for a B3 or G0, nor did I understand how to find out if it is B3 or G0 on the box...I will buy from retailer with no shipping.So, B3 or G0?I have read 16 pages with not so ver important info...And can anyone tell me what this means? BX80562Q6600
i.e. BX80562Q6600SLACR is a G0, BX80562Q6600SL9UM is a B3
Go for a G0.
RLM
I think its was around 15 celsius inside my room out side temperature was 13 celsius when I check my local weather. Btw my temperature was really high before around 45 C IDLE, LOAD 65 C Before I had to lapped my Thermalright 120 extreme heatsink after that I got nice temperature. I had one question I heard if you overclock ur cpu, cpus life goes down to half or something is this true? I will do the test again when temperature rise to 22 C.Quote:
Originally Posted by Snake_Eyes
G0 (= G-zero, GŲ), not GO.Quote:
Originally Posted by RLM
Didn't rea1ise that.Quote:
G0 (= G-zero, GŲ), not GO.
RLM
So I must go for A batch SLACR?Is that what you mean, for best Q6600 OC?:shrug: :confused:Quote:
Originally Posted by CraptacularOne
At this point I think no one really knows. It's all luck of the draw so far as there are A batches (SLACR) that don't clock as well as others A batches and the B batches remains to be seen. The one thing you don't want to see on the box is BX80562Q6600SL9UM (B3 quite a bit more heat for the same performance) if you are looking for a G0 Q6600.Quote:
Originally Posted by Fixt00l
http://mekk.homeip.net/imagesharing/...6c0162fe9d.jpg
Air :
http://mekk.homeip.net/imagesharing/...c24d6473a8.jpg
http://mekk.homeip.net/imagesharing/...5466ce2760.jpg
http://mekk.homeip.net/imagesharing/...191972ffd3.jpg
http://mekk.homeip.net/imagesharing/...9b246c89ea.jpg
Vapochill
http://mekk.homeip.net/imagesharing/...48b196d0aa.jpg
http://mekk.homeip.net/imagesharing/...11dd90940d.jpg
http://mekk.homeip.net/imagesharing/...0ff5d05ecd.jpg
Another 10min prime? http://www.helsinki.fi/~llounent/Web...blankstare.gif
btw, why do people take pics of Spi runs and benchmark screens? Screenshots are better quality and take less space. :confused:
That prime was just for fun.. i will post here when i will make a bigger pi time :). ( i stopped that after 2 hours, but i dont catch picture.. ).
I made that picture because when i launched the 3th Cpu-Z i got freeze :).
any one know why does it says on cpuz Core Voltage 1.152 V?? but it shows on core temp 1.2125V?
Here is again room temperature at 21 C
IDLE
http://img63.imageshack.us/img63/5386/97964715pl6.jpg
LOAD
http://img48.imageshack.us/img48/2372/49699004ei6.jpg
q6600 go. bios 1.19 vcore , low voltage 3040mhz
http://img146.imageshack.us/img146/1...6600ou2.th.jpg
I can't remember have I already post this here, maybe not.
Run with Little Devils SS Rotary. Can't say any temps, didn't have a termometer.
http://koti.mbnet.fi/boble76/Tietoko...Q6600/4510.jpg
M3kk, can you please resize your picture, make them bigger when your finish your fun... thank you
That 1.2125v isn't you vcore it's your vid. You have a very low vid and that's a very bad thing. Might I suggest you swap your chip with my much better 1.275.(J/K);)Quote:
any one know why does it says on cpuz Core Voltage 1.152 V?? but it shows on core temp 1.2125V?
Go by cpu-z 1.41 for your vcore.
As said the 1.2125 is your vid, and a very good vid. Nothings 100%, but you could have a very decent overclocker there:)
RLM
All this A vs B talk - I'm convinced it's the week.
I had a B3 L720B Q6600 which had a VID of 1.2750V - wasn't anything special. I did 3GHz at about 1.25V loaded on air. Sold it and got a G0 L723A which has a VID of 1.2375V, and it's doing 3.2GHz at 1.20V loaded on air.
I also posted 3.6GHz earlier (1.344V cpuz and 1.360V ET5 - average 1.35V I don't know which is more accurate) with very high temps of 70C+ after a few hours of prime. :(
Low VID chips are great - for water cooling. If I go over 1.4V loaded on my chip with my Ultra 120X (will get me somewhere in the 3.7GHz area) the temps get ridiculous. Now... if I only I had water cooling! No time for that unfortunately.
Hi guys, any one know why CPUZ is acting all weird and saying multi is at 6? I just got this processor into a P5K Deluxe tonight but too tired to mess around with it much. Plus its still on stock cooing :p
http://i223.photobucket.com/albums/d...172303_051.jpg:p:
http://i223.photobucket.com/albums/d...n/Untitled.jpg
That looks like a really low VID? no? yes? A little while ago I saw it move up to like 1.27 or the like, but it went back down and stays there at 1.1625. I can't catch it moving anymore.
Probably because you have speed step enabled in your bios...
Find another Jem :eek:
Water 20* Ambient cooled MP05LE
L720B035
2x32M SuperPI @4100mhz 1.51v only
Regarding Vcore problems on p5k vanilla , i think 4050-4100 are nothing to run Prime on it :))
http://img508.imageshack.us/img508/7...1512zz2.th.jpg
I disabled speedstep as well as "vanderpool technology" whatever that was, and now VID is staying at 1.2750v. However, CPUZ continues to show my multiplier as 6, probably cause i have it all left on AUTO. Sometimes when the CPUs are in use the multi jumps to 9 lolQuote:
Originally Posted by sdumper
Did you disable C1E as well ?Quote:
Originally Posted by breakneckspeeds
Let`s have a beginner question, O.K? What exactly "VID" is, and how does it reflect overclocking?And which is better-Lower, or Higher VID?
It appears that E6400 is a far better overclocker than any Q6600 (in percentage) on air cooling...Maybe I will participate in the next OC championship with my E6400, in order to get higher overclock, measured in percentage...