Printable View
OSKAR_WU posted something about problems with high FSB and SATA.Quote:
Originally Posted by bigtoe
I´m not sure if the problem was with the 1 & 2 SATA or 3 & 4. Someone wrote It was only with 2 of them but I'm not sure wich ones and I can't find that post anymore.
What SATA port did you use?
I'm running on ports 3&4 without problems but I'm only running 250 FSB (I think my problem is mye ram) If I buy some 3500EB I´ll go for higher FSB so I want to be sure I'm on the correct ports.
SATA will always lower your max oc'ing potential.. hence PATA is the way :)
jesus... the results from this board are just incredible.
Quote:
Originally Posted by eva2000
grrrr....so, turn-around to pATA again -_-
No, just use sata port 3&4, that's all.Quote:
Originally Posted by p4z1f1st
i'm using port#3 all the time -_-
@ all sATA-user: do u all use port #3/#4 too and get high HTT-clocks?
so... p4z1f1st im sry for this it cant be !
check port 1 or check it out to use an ide hdd to test....
i ve ordered my board till 2 weeks it should be shipped since 1 week but didnt came to me still now O_o i want it now! ! ! argh!
so "r" there now really high newcastle clocks it seems to me that the ch come better with this board but is it still a disadvantage to get a newcastle i only got a clawhammer here which does 2,4 instabile (:banana::banana::banana::banana:ty vcore issue) with 1,8 (1,728-1,84) modded bios on kda3+
maybe i could get higher with this dfi ;) and stable vcore but u guys "r" really crazy how could ya run with 1,8-1,9V on air? i get high temps with my water rig under load on 1,8-1,84 sooo i cant believe this with air.... should get over 65degreeC
hope my board comes tomorrow i wouldnt wait any longer soo PLZ!!!!!
BTW... i also get msiRX9800 on 513/407 for benching with very littl artifacts and still no on 500/396 :) i m very happy thx @ hell-fire and funktional again for helping with the vgpu mod :D
seEn andL
hm, so....
i meantioned that the boot-screen shows me following, while i always deactivated sATA-port 1&2
external phy - port3: *name-of-my-plate*
external phy - port4: *empty*
so i thoght "hm, maybe the fuc*ing board sets all sATA-ports to the marvel-chip, when i deactivate 2 of them"
so, i activated them and then it showed:
external phy - port1: *empty*
external phy - port2: *empty*
internal phy - port3: *name-of-my-plate*
internal phy - port4: *empty*
so, i tried FSB 1:1 266MHz (260MHz is my maximum) with test#5 @ memtest....but it hanged up (like everytime >260MHz) after 32sec.....now i really get fuc*ed up! :mad:
i think, i'll get a pATA-hdd from my friend and try via pATA :mad:
also u tried async. memory and all dividers also 0.5 and raise cpu core/volt settings changing sata ports also all this tweaks in bios what ya could set and with any other tools where u could set something u tried em all?
maybe something limits ur oc and it isnt the board ?! (ram cpu dont know...)
also is there somebody who could post high htt clocks and so on with a newcastle?
seEN andL
PS: has anybody ordered the dfi from oc-wear in germany from outside it => how long did ya wait for?!
http://www.xtremesystems.org/forums/...403#post546403 :)Quote:
Originally Posted by andL64
oj ;) i read that shortly b4 ;) sry mate didnt recognize u got a nc :D
guys, do u all have enabled both sATA-controller?
or are here guys, who disabled port #1 like me and got high HTTs?
now i'm pis*ed of, by setting all the time the cmos-clear-jumper....so, first i've to get down and then maybe i'll try it again....
So from what I am reading you have to use SATA ports 3+4 if you want to clock high on the HTT? Is there any performance difference with them on 3+4 in a RAID 0 over them on 1+2?
folks using BH-5/6 at >260mhz 2-2-2-6 speeds what are you setting the other mem timings for
Trc
Trfc
Trrd
Twr
Twtr
Trtw
Refresh Period
Write CAS Latency
and ones further below them
???
please share :)
Just play with them and see what works....test one at a time...best way to do it if you don't know what they do.
Use the A64 tweaker and change one and one and run sandra/pi between changes. Take screenshots ones and awhile when getting higher score.
Seem to be easiest.
Wish there was a save/load settings on A64 tweaker.
Where do you get that program from? I want to try that out.
*EDIT* Nevermind I found it. Google is a wonderful tool :p:
yeah that's good to test once you know fairly well what the mem max is.. but i'm trying to determine what if any of these settings would allow BH-5/6 to go that bit higher than normally would while still maintaining decent overall performance/bandwidth - just that little bit extra heheQuote:
Originally Posted by Ubermann
i.e. memtest86+ v1.26 bandwidth with 1x 256MB KHX3000K2/512 BH5 stick
auto unless overwised specificed
9x 260mhz 2-2-2-6 1T = 1757 MB/s
9x 267mhz 2-2-2-6 1T = 1805 Mb/s
9x 260mhz 2-2-2-6 1T 10-12-2-2-2-2 = 1865 MB/s
9x 260mhz 2-2-2-6 1T 9-12-2-2-2-2 = 1905 MB/s
9x 267mhz 2-2-2-6 1T 9-12-2-2-2-2 = 1956 MB/s
eva2000 keep up the good work! Post what gives you the best results.
I`ll get the board on saturday and I`m goning to pair it up with 2x256MB BH-5 and 2x512MB Ballistix.
This will be my first A64 board, and I just know I`m going to love it! :D
Man oh man I got too many things I want to test and tweak. There is too much and so little time I have to do it. Why can't I just sit at home all day? lol Work sucks!
hm guys, could u tell me, which DRAM-Slots u use?
btw. i got a pATA-HDD from a friend and it didn't help.....so, now i've to get a new A64 somehow, to see, if it's the CPU, which can't handle the high HTT-clock
because, the lowest HTT on the new DFI I've seen here, was around 320MHz....so, i'm not really sure if it's my DFI....
I'm using 1&3 but it doesn't matter, just put the RAM out of the way by using the 1/2 divider.Quote:
Originally Posted by p4z1f1st
Don't bother with ClockGen, just go into bios, select this divider, set multi to 5x and set your HTT to somewhere around 350.
Leave everything else on auto.
Press F10 and enter.
What does it do?
just, before i have again to set my cmos-clear-jumper - why press F10?
does the DFI has a secret-option-menu like some Gigabyte-boards? :confused:
No F10 is to save and exit. :)
Went a little bit higher on HTT, not stable but great numbers. :banana:
F10 is save and exit.