Water Cooled Case Gallery

Sorry for the blurry pictures, my P&S has issues and I'm saving for a K10D so ...

This is the first time ever I built my own PC and it took me quite a while, but it was well worth it !

http://www.envimon.com/francis/newri...ig1_resize.jpg

http://www.envimon.com/francis/newri...ig2_resize.jpg

http://www.envimon.com/francis/newri...ig3_resize.jpg

http://www.envimon.com/francis/newri...ig4_resize.jpg

http://www.envimon.com/francis/newri...ig5_resize.jpg

http://www.envimon.com/francis/newri...ig7_resize.jpg

wow, the filling port is below the pump

that should have sucked while filling

LOL you shoulda watched me fill my old PC7 build. Tri rad @ top, pump second lowest, res LOWEST. Oh man. *shudders*

need a hug ? :P

LOL

seriously, that should have been a real PITA

Quote:

---

Originally Posted by TRG

DDC upside down = bad ?

---

It may or may not be true, but it's just something I heard.

I fill and bleed my system upside down :D

Quote:

---

Originally Posted by petercintn

I had this thrown together to start with, one of Petra's kit's and once satisfied that I knew what I was doing (first W/C build) I took my rig apart and here's how she ended up. My rad and pump are in the tv stand that was used as a base for the case.

http://img260.imageshack.us/img260/4489/050rm9.th.jpg

http://img260.imageshack.us/img260/7044/053ql4.th.jpg

I have changed the tubing that Petra's gave me with the kit to 1/2" id, 3/4" od. Plus I guess the small tubing that came with the kit when I tried to push it on the plastic barbs for the rad, I pushed too hard and caused a leak. Or the rad was defective. Reguardless, I tried many different ways to stop the leak and finially took it to a rad shop and had it fixed. Cost as much as the rad. Maybe I could have bought the resin and solder and a torch and did it my self, but I wasn't sure I could. In the pic that's rtv all over the rad and tubing.

All in all, I think it turn out good, just need to buy more blue stuff to put in the water.

---

is the the tv mounted atop your pc :ROTF:

My e6600.....

Asus p5b-plus with danger den rbx cpu block, and danger den Northbridge block. i had to make adapters out of 1/2" lexan for mounting the blocks! it worked well.i had the water stuff from my last build, which was an amd 2400+mobile on a dfi lanparty board. it died when i accidentally dremmeled the MB :(

heres a quick pic.

you've dremmeled the mobo??? wtf were you doing? cutting case with hw in it? poor mobo...
do you have any pic?

quick setup, have no place in case to put this tripple rad in....
must design some custom wood case for this rig

Quote:

---

Originally Posted by Yozzman

Nice paintjob man!!!

Only missing the wires:rofl:

---

Cheers Yozzman - got some wires in at last :cool:

System Spec:
Tyan Tiger K8WE S2877ANRF
2x AMD Opteron 265 dual core SKT 940 Retail (1.8Ghz-0.9nm-2Mb)
4x 512GB OCZ 3200 EL DDR ECC Reg / Dual Channel
Gainwards 8800GTX Ultra Golden Sample
Antec 850 True Power Quattro PSU
2x 74GB Raptors

Watercooling:
2x Danger Den TDX A64 Blocks
Danger Den NV8800 Block
Danger Den Hard Drive Block
Laing DDC 10watt - Alphacool Dual Plexi Res
HWLabs Custom Made GTX X-Flow
2x Yate Loon D12SL-12
Tygon Hose
Fesser One Liquid

http://www.coolercasesuk.co.uk/rossi.../Stack_129.jpg

http://www.coolercasesuk.co.uk/rossi.../Stack_130.jpg

v nice PSU, and gr8 rig :D

Quote:

---

Originally Posted by SaFrOuT

iam sure he is using the most famous coolant, the swiftech HydrX

---

It is actually the dye from FrozenCPU.com :D

wow. very good paint job. Was it done with a compressor?

Quote:

---

Originally Posted by metalman2785

It is actually the dye from FrozenCPU.com :D

---

/me finds a place to hide

:D

which one is it please ==> here

Quote:

---

Originally Posted by SaFrOuT

/me finds a place to hide

:D

which one is it please ==> here

---

This one, great deal for 5 bucks, it only takes a few drops for the entire loop. My little bottle will last me a lifetime :)

http://www.frozencpu.com/products/17...tml?tl=g30c103

ya it looks very nice for sure

Quote:

---

Originally Posted by SaFrOuT

ya it looks very nice for sure

---

Thanks!

I just ordered a couple silent x red led fans to replace the blue led fans it came with :D

Hi guys

Here is my Lian Li V2000 with a Quad raiditor with (4) Silverstone FM121 fans on it. Swiftech 655 pump with 1/2 tygon tubing. Running a Storm on a Opt 165, cpu never goes over 32c on load. Planning on modding a second Quad next to the other one and put PSU and 2 raptors in the 5.25 bay area.

Amd Opteron 165 1.8 to 3.0
Asus A8N32 SLI
Corsair XMS PRO DDR550/PC4400 2GB
(4) x 36 Raid -0-
eVGA 7900 GTO
SB XF-i

http://i.pbase.com/g5/06/629506/2/67441607.cMVAa00a.jpg
http://k43.pbase.com/g3/06/629506/2/...5.za0BKrx9.jpg
http://k53.pbase.com/g5/06/629506/2/...0.lw0GbEVS.jpg

Nothing to special,

My first watercooled Rig :D

parts:
-eheim station 600 (600litre 1.3m)
-masterkleer 1/2 tubing
-Swiftech Apogee GT (bowed)
-Black ICE GT Stealth 240 radiator

temps:
3600mhz 1.47v Orthos = 59C max.
3600mhz 1.47v WCG+other apps = 53C max.
3600mhz 1.47v 3dmark = 52C max.
3500mhz 1.42v Orthos = 50C max.
3200mhz 1.28v Orthos = max 46C max.

Tuniq 3600mhz 1.47v not Orthos stable = max 72C (tuniq sucks)

I like the Rad mounting, rad mounting like you never seen before :D :cool:

The first picture was without UV light, and was way to boring. In the other pictures you can see UV light.
http://img256.imageshack.us/img256/8...4411um6.th.jpg

http://img267.imageshack.us/img267/5...2151is2.th.jpg

http://img201.imageshack.us/img201/9...9021kb8.th.jpg

http://img294.imageshack.us/img294/5...6231md7.th.jpg

http://img201.imageshack.us/img201/9...4608lc6.th.jpg

http://img503.imageshack.us/img503/5...7659ul5.th.jpg

http://img158.imageshack.us/img158/7...7686ig8.th.jpg

http://img441.imageshack.us/img441/8...7611br3.th.jpg

http://img441.imageshack.us/img441/8...5799sg4.th.jpg

http://img104.imageshack.us/img104/522/10jy1.th.jpg

@ ownage

The most original WC filled P180 I've seen so far :)

Care to sell your sidepanel? (mine is broken :()

Updated my V1000. Do I hold the award for most stuff in 1 yet?:D Hardware specs as in sig.


http://i202.photobucket.com/albums/a...e/DSCF0033.jpg

http://i202.photobucket.com/albums/a...e/DSCF0035.jpg

http://i202.photobucket.com/albums/a...e/DSCF0021.jpg

http://i202.photobucket.com/albums/a...e/DSCF0036.jpg

Quote:

---

Originally Posted by TRG

@ ownage

The most original WC filled P180 I've seen so far :)

Care to sell your sidepanel? (mine is broken :()

---

Thanks :D ,

I rather keep my sidepanel, because i mostlikely will use this case as my server case after some time.

Quote:

---

Originally Posted by metalman2785

This one, great deal for 5 bucks, it only takes a few drops for the entire loop. My little bottle will last me a lifetime :)

http://www.frozencpu.com/products/17...tml?tl=g30c103

---

Wow really... Sounds like a better deal than the D-tek UV dye I'm using. Took about the whole bottle to get it about that bright, and the bottle is $10. Might have to look into that frozenCPU dye next time.

Quote:

---

Originally Posted by [XC]Atomicpineapple

Updated my V1000. Do I hold the award for most stuff in 1 yet?:D Hardware specs as in sig.


http://i202.photobucket.com/albums/a...e/DSCF0033.jpg

http://i202.photobucket.com/albums/a...e/DSCF0035.jpg

http://i202.photobucket.com/albums/a...e/DSCF0021.jpg

http://i202.photobucket.com/albums/a...e/DSCF0036.jpg

---

jeez i cant even see the motherboard :p:

Quote:

---

Originally Posted by whoodiestyle

jeez i cant even see the motherboard :p:

---

:rofl:

i was thinking the same thing...

Quote:

---

Originally Posted by kinghong1970

:rofl:

i was thinking the same thing...

---

me 2 :lol:..

how can u even manage the wires n Pipes..

the only thing i can see is the Res :confused: :p:

It was a difficult job, took pretty much all day with a stop for rowing and food. Nothing went to plan really. I was hoping to fit the MCRES in between the side of the case and the 5.25" drive bays but its too wide, thank God for the included bracket! I was planning to have the 2nd DDC below where the MCRES is but that wouldnt work either so it had to go at the back of the case next to the other 1 and its a tight fit, only just goes. I have a modular PSU so that helped, along with the impressive flexibility of 7/16" Masterkleer tubing, I dont think I'd have managed it with 1/2" tubing, be just that bit too big.

Loops go (1) DDC-1+>Fuzion 1>Fuzion 2>Rad>MCW-60>EK Res
(2)DDC-1+>BIP>MCW-30>Maze 4 GPU (on PhysX)>MCRES Micro

I'd planned to watercool the southbridge with a 2nd MCW-30 but I couldnt get a secure mount due to the intel clip hold down mechanism. The NB was fine as the i5000X chipset is covered by an IHS.

Quote:

---

Originally Posted by [XC]Atomicpineapple

It was a difficult job, took pretty much all day with a stop for rowing and food. Nothing went to plan really. I was hoping to fit the MCRES in between the side of the case and the 5.25" drive bays but its too wide, thank God for the included bracket! I was planning to have the 2nd DDC below where the MCRES is but that wouldnt work either so it had to go at the back of the case next to the other 1 and its a tight fit, only just goes. I have a modular PSU so that helped, along with the impressive flexibility of 7/16" Masterkleer tubing, I dont think I'd have managed it with 1/2" tubing, be just that bit too big.

Loops go (1) DDC-1+>Fuzion 1>Fuzion 2>Rad>MCW-60>EK Res
(2)DDC-1+>BIP>MCW-30>Maze 4 GPU (on PhysX)>MCRES Micro

I'd planned to watercool the southbridge with a 2nd MCW-30 but I couldnt get a secure mount due to the intel clip hold down mechanism. The NB was fine as the i5000X chipset is covered by an IHS.

---

Thats totally the opposite then wat i want with my Rig. I want my loop to be as simple as possible, which makes it easy to remove, but also doesn't take to much space.

Your Watercooling sure looks cool, but what when you have to remove something? :ROTF:

Yeh, it sure wont come apart easily! Really the only reason it'll come to bits now is if something breaks. I wont be upgrading for a while as Im not a heavy gamer I wont be rushing out to buy the latest GFX card and the dual-quad cores should see me through in the CPU horsepower department for a good while to come. My 1st loops started off simple, was an Asetek CPU only kit, then I bought a GPU block, a better pump, the Antarctica CPU block. Having pushed the Asetek stuff about as far as it would go I got a Laing D5, a tripple 120 rad, a DD TDX for my A64 and a Maze 4 for my GFX. From there I added a 2nd D5 and swapped to an MP-05 Pro LE CPU block. When I got my 1st Xeons (E5120 dual cores) I just bought a 2nd MP-05 and an MCW-60 for my 8800GTS as the Maze 4 wouldnt fit, but when my quad cores arrived I upgraded to the Fuzions due to their made-for-quad-core design and thought I may as well do it properly and WC everything! The stock NB heatsink is just Alu and it got burning hot so I got the MCW-30s and I still had the old Maze 4 knocking around which just happened to fit on the PhysX card, so might as well use it, right?

I do see your point though simple can be good, but at least if I know it'll take all day to disassemble it'll stop me tinkerign for a while, might actually get some useful stuff done! D

Quote:

---

Originally Posted by coolrmaster

is the the tv mounted atop your pc :ROTF:

---

Who needs an idiot box anyways? :D

Not as pretty as some, but it works for me ; )

LL G70B
Tagan 1100W PSU
eVGA 680i
eVGA 8800GTX
E6600 @ 3.8
4GB OCZ PC8500
BI GTX360, D5, EK Res, EK GPU, DD NB, D-Tek

http://img511.imageshack.us/img511/3768/g701sb1.jpg
http://img389.imageshack.us/img389/9453/g702tu7.jpg
http://img518.imageshack.us/img518/7826/g703hc5.jpg

i like it...quite clean job ;)

and...what about the temps??

What i dont like is the routing of your tube that goes from the D5 to ur rad...
I would have put it above the mobo...
Then it wil look even more cleaner ;)

And mayby a different color for those green mesh... :P

Just finished mine ...

still bleeding -

http://members.iinet.net.au/~hazay/P...e/IMG_4984.JPG

hey! there's my EK block I sold to omarko, looks bloody terrific mate!
loosen the screws up a bit, your bending the PCB, look at the pic again and look closely at around the SLI conector

what's that tubing under the GTX doing there? holding up it up is it?

hah tubing holding the gtx up, thats innovative. great job!

but fo real, that build is tight brah!

Omarko why is your card bending so much at the end? my 8800gtx with the ek block holds it all rigid and straight

Where is the PSU getting its air from? The fan is on the bottom, but there is the bottom of the case in the way...? Or am I just missing something, like is there an airspace between the bottom of the PSU and the case?

Quote:

---

Originally Posted by whoodiestyle

Omarko why is your card bending so much at the end? my 8800gtx with the ek block holds it all rigid and straight

---

I think he did put the EK block to tight...
I had it to when i put on my 8800GTS...
I just loosend some bolts a bit... :)

Quote:

---

Originally Posted by whoodiestyle

Omarko why is your card bending so much at the end? my 8800gtx with the ek block holds it all rigid and straight

---

not sure to be honest ... I tried few things, makes no diff ...

Quote:

---

Originally Posted by SparkyJJO

Where is the PSU getting its air from? The fan is on the bottom, but there is the bottom of the case in the way...? Or am I just missing something, like is there an airspace between the bottom of the PSU and the case?

---

the PSUis elevated about 3cm above the bottom of the case so there is plenty of airflow going on in the bottom chamber which is separated and insulated from the top one. There is a front intake fan pushing air in and going out through the PSU.

Quote:

---

Originally Posted by Yozzman

I think he did put the EK block to tight...
I had it to when i put on my 8800GTS...
I just loosend some bolts a bit... :)

---

I tried that and it made not difference. :( its wierd ... but all seems to work fine ...

I gotta say, the temps are fantastic, in 19C room temp I get 31C IDLE and 35C LOAD (playing Oblivion for approx 2 hours). With stock HSF I had 65 Idle, 75C load. Massive drop.

I start feeling Nervous and Tensed when i see Bend PCBs

Nice work there Omarko on your P180!

Little upgrade....

4GB OCZ ram watercooled:


http://www.bilder-hochladen.net/files/thumbs/397u-1.jpg

Quote:

---

Originally Posted by LeChuck

Little upgrade....

4GB OCZ ram watercooled:

---

nice ... thats what I call EXTREME :)

nice rig Omarko, i like the simple view unclutterred look...

LeChuck, i almost couldn't see the shiny ram... that is 1 big blowup of a pic.

New PSU. The old Enermax Liberty is defective. The Corsair is just perfect for cable managment :)

http://www.abload.de/img/wak182jxd.jpg

http://www.abload.de/img/wak18_bestesbildever1tm.jpg

http://www.abload.de/img/wak184h04.jpg

http://www.abload.de/img/wak181gnm.jpg

Steffen WOW ddue i like alot

What case is that? A-10 ?

Yeah me like too! Except for the small tubing and 90degree barb :rolleyes:

How did your PSU break steffen?
Did you get a replacement?

these are my first and second attempts of watercooling.

here's what mine looked like last year:
http://i69.photobucket.com/albums/i4...029-resize.jpg

i changed a few things and finished this a few days ago:
http://i69.photobucket.com/albums/i4...256-resize.jpg

*don't mind the fingerprint smudges, i don't have a window so i don't care to clean them but i will when i feel like it ;)

@Steffen

your case is beautiful:)

Quote:

---

Originally Posted by aiya

these are my first and second attempts of watercooling.

here's what mine looked like last year:
http://i69.photobucket.com/albums/i4...029-resize.jpg

i changed a few things and finished this a few days ago:
http://i69.photobucket.com/albums/i4...256-resize.jpg

*don't mind the fingerprint smudges, i don't have a window so i don't care to clean them but i will when i feel like it ;)

---

very simple/clean looking loop...:clap:

Nothing special but i love the temps :)

Old P4S800D-X died. Replaced with an Abit IC7:

http://i5.photobucket.com/albums/y16...AbitIC7002.jpg

Quote:

---

Originally Posted by Riddlinkidstone

Old P4S800D-X died. Replaced with an Abit IC7:

http://i5.photobucket.com/albums/y16...AbitIC7002.jpg

---

wc setup isn't bad, but what's with those purple exhaust fans? ;)

Quote:

---

Originally Posted by coolrmaster

wc setup isn't bad, but what's with those purple exhaust fans? ;)

---

Hehe.

Well I ordered some "UV LED" fans from SVC and they just came UV reactive. I emailed them and they said sorry, corrected the website, and offered to take them back for a full refund plus they would pay for shipping.

I get most of my modding gear from SVC so I told them it was fine but they insisted they do something for me so they said they would give me a discount on another set of fans so I got some sexy green aluminum fans for another project.

They look so damn sexy under UV light. MmmmmMmmmm goodness. :up:

Quote:

---

Originally Posted by coolrmaster

wc setup isn't bad, but what's with those purple exhaust fans? ;)

---

They're not purple...blue actually :p: . AFAIK, they are the screwless fan holders (or clips) found in some cheap cases.

Brendan

Quote:

---

Originally Posted by coolrmaster

wc setup isn't bad, but what's with those purple exhaust fans? ;)

---

They're blue? lol

...a bunch of new pics out of my "laboratory" ;)

http://www.abload.de/img/inside1wj.jpg

http://www.abload.de/img/heatkiller700.jpg

http://www.abload.de/img/swiftech2j3d.jpg

http://www.abload.de/img/swiftech3by8.jpg

http://www.abload.de/img/alphacool-snb-a8iv.jpg

http://www.abload.de/img/zern1ld6.jpg

http://www.abload.de/img/zernpqpoliert252l.jpg

http://www.abload.de/img/img_24890ii.jpg

http://www.abload.de/img/img_25065gy.jpg

nicceeeeeeeee

That last block is suhweet!!!!!

Post them in a thread so they are easier to find and post how you made them and stuff!!!!!!!!

inside
http://koti.mbnet.fi/boble76/Tietoko...Kuva%20023.jpg
outside
http://koti.mbnet.fi/boble76/Tietoko...Kuva%20025.jpg

Mobo has changed but otherwise almost the same...

Weird watercooling set-up Boble76! What are temps like ?

Oh and BTW: I know that little "TV" desk. I have the same. Let me guess...IKEA ? :p:

Quote:

---

Originally Posted by Patriote

Weird watercooling set-up Boble76! What are temps like ?
Oh and BTW: I know that little "TV" desk. I have the same. Let me guess...IKEA ? :p:

---

What's so weird? :D
CPU: +37-39 IDLE
GPU: +43C IDLE (max +47C LOAD)
Yes, it's possible from IKEA, I'm not 100% sure about that..:shrug:

http://koti.mbnet.fi/boble76/Tietoko...%f6yt%e4_x.jpg TEST SETUP :ROTF:

@Boble76

Haha, i have a similar bench table also. :)

@ bundymania love the innard's of that block.

@Bobble excellent, i'd love to go wc but im not sure about what case (or even if you use one) so that layout your using (in the box) seem's like a really viable option for me too

thx guys! i bought the last block @eba* in a set with pump and stuff , dunno who made this little beauty, sry :(

Quote:

---

Originally Posted by Boble76

What's so weird? :D
CPU: +37-39 IDLE
GPU: +43C IDLE (max +47C LOAD)
Yes, it's possible from IKEA, I'm not 100% sure about that..:shrug:

http://koti.mbnet.fi/boble76/Tietoko...%f6yt%e4_x.jpg TEST SETUP :ROTF:

---

What happens if your little brother or whoever spill your water while your computer on? possible frying your cpu and gpu? : )

Quote:

---

Originally Posted by bundymania

thx guys! i bought the last block @eba* in a set with pump and stuff , dunno who made this little beauty, sry :(

---

Looks like it might be an older generation of this block

is it me or does our EU folks seem more artistic in their blocks?

Quote:

---

Originally Posted by kinghong1970

is it me or does our EU folks seem more artistic in their blocks?

---

yes because amircans just like Big stuff :D (example cars )

New Pictures of my build. Ya its the Black Pearl :up:
http://benstyle.de/projekt/closeup.jpg
http://benstyle.de/projekt/seite.jpg
http://benstyle.de/projekt/detail.jpg

nice looking BeeN

[QUOTE=bundymania;2303342]...a bunch of new pics out of my "laboratory" ;)

http://www.abload.de/img/inside1wj.jpg
What are you using to get the red color in your water? I'm using red food coloring for mine but I'm not sure if its a good idea.

Budy is using Food Color too :cool:

I dont see how food coloring could/would hurt flow...maybe I am wrong...*-)

My Giant watercooler AM2 :D

Big...Big...Big

DarkWing6611: I hope you have some killer pump for that block...lol

omg thats huge, post some temps.
btw, what are you using for VRMs, NB+SB? i have same board, so im asking ;)

i think this is not a good design cause with the very wide area for water to run in and the very small opening i guess most of the water will run @ the middle of the block while the rest @ the sides will be much slower

While it looks very well made, I think the pins are just too thick to properly dissipate the heat quickly enough.

Here is some of my p180. This is what I had to work with. I have replaced the noctuas with YL's and I just ordered a MCR320 to replace the two radiators.

http://www.turborocco.com/watercooledp180.jpg

http://www.turborocco.com/watercooledp1802.jpg

Nice and clean.

Make sure you fill up that Swiftech Micro-Res to the brim though.

Look at what the delivery guy brought me today! :D

http://img165.imageshack.us/img165/1...0001yk4.th.jpg

http://img258.imageshack.us/img258/1...0005tx4.th.jpg

http://img19.imageshack.us/img19/351...0006to8.th.jpg

Stuff in pics:

2x Sound dampening material
1x Logisys dual 12" UV Cold cathodes
1x A.C. Ryan Twinoverboost dual 12" UV Cold cathodes
4x Yates Medium speed (For push pull config with my current Scythes!)
1x Techflex Sleeving kit + some 1\4" Sleeving and 3\8" Heatshrink
1x OCZ XTC Ram cooler
1x EK Multioption reservoir 150
4x Cold cathodes extensions
6x EK barbs
2x DD Hi Flow barbs
10x Blue leds
30+ Zip-ties
1x DD Black Fill-Port
4x Rubber feet
1x Thermalright Back plate for my Fuzion
1x MCW30
1x EK 8800GTX Full-cover WB (Damn thats one sexy block!)
10" Tygon 1/2" ID 3/4" OD Tubing
20" Masterkleer 7/16" ID 5/8" OD Tubing (Just for the heck of it...lol)
1x Coolsleeves 625 UV Blue
1x Coolsleeves 625 Clear
1x Coolsleeves 625 UV Green
1x PT_Nuke
1x D-Tek Fire Red Dye
1x D-Tek Alien Green Dye
1x D-Tek Visible Blue Dye
1x D-Tek Orange\Yellow Dye
1x Swiftech's Hydrx
2x G11 Pentosin and one half UV bottle
1x Half Zerex bottle

Oh and the P5W DH Deluxe is just there because my good friend, cadaveca, fixed it for me and i got it back today! Thanks a tone m8! :D

This stuff above + what i currently have (See specs in sig) will do a freaking nice build in my U2-UFO :D

Got enough colours of dies? :)

Quote:

---

Originally Posted by Trike

Here is some of my p180. This is what I had to work with. I have replaced the noctuas with YL's and I just ordered a MCR320 to replace the two radiators.

http://www.turborocco.com/watercooledp180.jpg

http://www.turborocco.com/watercooledp1802.jpg

---

why not putting that gpu under water too?

Quote:

---

Originally Posted by SerialSniper

Got enough colours of dies? :)

---

Well, check this out. Take, let's say, about 1 Gal of distilled water, pour some of all the dyes + some G11\Zerex + some PT_Nuke you see in the pics above and you get a freaking UV Brown coolant flowing in your tubing! Now thats Xtreme! ROFL! :rofl:

Nah but seriously, i want to make sure i had the choice of color when i would have made my choice :) You know just in case...

Still, is nothing compared to Mr. H20 that, a few months ago, got some Xtra C2Ds mobos just in case...LOL Anybody know what the heck im talking about ? :D

Quote:

---

Originally Posted by Mad_Man

why not putting that gpu under water too?

---

Um... Maybe because of space restriction and temps would suck with such small Rads ? :rolleyes:

well, the 320 should keep it fine... at least i think ;)

That's right Madam the 320 will cool both no problem. Trike where u puttin the triple?

Quote:

---

Originally Posted by coolrmaster

That's right Madam the 320 will cool both no problem. Trike where u puttin the triple?

---

I Decided not to cool the gpu with this setup as the radiators are already heatsoaking. My idle temps right now are pretty bad. 36C. Vcore is set at 1.5 i'm only at 3.3 stable right now. This is on a lapped Xeon 3060. Kinda dissapointed with the results. I can run 3.6 no problem and orthos no problem, but once I start rendering some video, the video ends up with artifacts. took me a while to figure out it was the overclock. I was hoping i could hit 3.8, but seems unlikely.

Now i'm going to mount the MCR320 on the back with a rad box. Figured this would be the best bang for the buck upgrade. more surface area and reduce the pressure drop by getting rid of the two radiators.

I'm still debating if i want to cool the 1950xt. I don't know if i'm going to upgrade the vid card soon. I guess the MCW60 is fairly compatible with both nvidia and ati.

With the GPU added into the loop, how much higher will the temps be? Would I get better results if i just left the gpu out?

I'm not really overclocking the vidcard right now, but there's still alot of heat coming off of the hs/fan.

@Patriote: ohh damn :eek: wht ur going to do ? cool ur House with all that :rolleyes: 30feet tubings FTW !!!

Patriote you gonna stack 4 cubes together and watercool em....
or should i think that you're gonna cram your ufo to the limit...

There isn't that much stuff guys :D But yeah ima "cram" my UFO! LOL

http://img.photobucket.com/albums/v6...ude/precpu.gif

Nice setup Redstars :D

wht r the Comp n WC specs ?