Printable View
happy to be able to reach 540 fsb with that mobo on air
4.6 ghz ( 8.5 x 540 / PC 6400@1080 4-4-4-4) 1.56v real bios ( set at 1.68v )
http://valid.x86-secret.com/cache/banner/331019.png
http://images3.hiboox.com/vignettes/1208/ajvvi46k.jpg
something strange I couldn't raise VMCH more than 1.4v ( 1.5 and 1.7 available bios 903 asus P5K-C )
Regards
Whats the verdict?
Anything over 4.0 needs the big volts?
I got the E3110 and it requires less voltage than the two E8400 I had, which were stable at 445 MHz x 9 @ 1.365v in bios. The E3110 is stable at 460 MHz with the exact same settings, although with the higher FSB I backed off the Performance Level to 8, from Level 6
Not sure about maximums, but I o/c my E8400 to 4630 MHz @ 1.60v and this E3110 should do 4.6 with under 1.50v
Great, 1.36 in bios, what would that be in real terms on the P5k?Quote:
Originally Posted by Xvys
On my P5B 1.36 bios = 1.296 real
The P5K has Load Line Calibration, which reduces the vdrop and locks in the voltage closer to bios settings. So 1.365v in bios drops to 1.344v at idle and about 1.337v under load. If the load line is disabled, then more voltage is required for stability...such is the case with the P5B.
I had the P5B vanilla with a E6300 and it ran 24/7 at 490 MHz X 7 with 1.375v in bios. After vdrop the voltage would show 1.32v at idle. With that setup it o/c to 533FSB x 7 = 3730 MHz. With my P5K Deluxe I could only match the 3730 MHz with the E6300, but no better, despite all the voltage and bios adjustments with the P5K-D.
Tonight, I ran some basic tests at 4600 MHz, not bad for air cooling, at a little lower voltage than my E8400.
This E3110 runs way hotter than my E8400. Not sure this is due to the thermal diodes actually working, and not being stuck like on both of my E8400's? But it shows about 20C higher under load.
Xvys
it seems that xeon's run hotter than 8400 and requires less vcore to reach same frequencies .
You should mention too taht " load calibration line " seems only efficient with deluxe P5K and not working on others .
I still have lot of vdroop on P5K-C with voltage damper enabled and this issue was already described on another topic .
I should be getting my E3110 today.
I'll do some quick testing on the P5B Vanilla and if it doesnt like it Ill run out to get the P5K- Premium.
My real concern is the fact that any bios I tried on my P5B after the 0701 just wont overlock at all. ANd I need a new bios for the Xeon...So I dont know if its just the combo of the E6300 and the new BIOS that is bad, or its just new bios plus my P5B = not going anywere. I know its not ram cause its doing the same thing with different sticks.
i wonder if one gets the dfi dk p35 right now together with an e3110 , how one will manage it to work? don't it need a bios update? or do they work right away and recognize it (same goes for other 45nm like e8500 or q9450 etc.)
If your picking one up at a store then look for the 45nm sticker....All boards Ive come across that are retail and do support it have a sticker on them "45NM supported"Quote:
Originally Posted by vcp-cur
If your getting it online them maybe email em first.
P.S No E3110 today, picking it up at the post office tomorrow. Ill come back with a report.
Here is my best 1M SPi time so far with the P5K-Premium. Gotta little more tweaking to do.
nice sofarfrome :up:
does anybody actually run E3110 with batch ending with "T" ?
Max CPUZ Validation @1.48v idle vcore hitting my max 32M PI stable FSB of 545FSB so no idea if FSB limited me or vcore or both heh. I was running 4x1GB Crucial Ballistix PC2-8500 as well :)
http://fileshosts.com/intel/Asus/Bli...4638mhz_tn.png
http://fileshosts.com/intel/Asus/Bli...uz_4638mhz.png
Now to move from Windows 2008 and install Vista Ultimate SP1 64bit :)
Quote:
Originally Posted by eva2000
nice xeon and mem !
Do you have some feedback from other Q750xxxxx owners ?
Some quick results
http://www.is-mad.com/upload/userfil...110_TEST_1.jpg
Myn is batch Q745A784
Pack Date 02/06/08
450fsb @ 1.352 but drops to 1.312 under load...seems that Vdroop is way higher on with this chip then with the E6300....where underload my voltage would only drop 0.016
At first I was paranoid cause it just wouldnt boot at anything between 390-410FSB....regarldes of voltage. So I just said "f*c* it" and gave it 450 and it worked fine :)
THe above is stable in the 8mb two core Pi and 3dmark06...
More will follow.
only other Q750A158s i've seen are PC's results http://www.xtremesystems.org/forums/...d.php?t=181476 and spyboy48's one http://forums.vr-zone.com/showthread.php?t=242957Quote:
Originally Posted by Mykou
thnks for links evaQuote:
Originally Posted by eva2000
Wasnt that stable at 1.352...Had to bump up to 1.392, 1.33* under load to pass OCCT.
Before it would pass superPi 32 but not OCCT...
It really likes the volts. I'll wait for my 120Ultra before I go higher.
http://valid.x86-secret.com/cache/banner/335993.png
Q746A535
http://img259.imageshack.us/img259/76/img04791oh9.jpg
Max FSB H20 = 580. Hoping for more sub zero.
http://img141.imageshack.us/img141/4395/mar94lc1.jpg
1.31v for 4G Orthos.
http://img404.imageshack.us/img404/4947/mar95jk3.jpg
Board = DFI P35 T2RS
Some results with my Q746A534 E3110 1.55v idle cpu-z on AIR!!
http://img232.imageshack.us/img232/7682/superpibzy5.jpg
http://valid.x86-secret.com/cache/screenshot/331544.png
http://valid.x86-secret.com/show_oc.php?id=331544
Testing stable OC now 1.35v FULL:
http://img219.imageshack.us/img219/1...1043ghzcb9.jpg
Great chip :up:
What's up with this?
http://geting.se/image.php/93971-mar95jk3333.jpg
Your other CPU-Z screen doesn't say e8400 anywhere :)
Quote:
Originally Posted by Eldonko
not the same version of cpu-z
1.44.1 vs 1.43
Yeah, I tested stability before FSB and got new cpuz in between. Good attention to detail tho. :D
yes
had to download it to validate my new max fsb at x 9
532 x 9 lol on this crappy board and its max 1.4v stuck on NB :p:
and still dude for pencil mod > 1.59v real vs 1.56 max before (1.70 set in bios ) :ROTF:
4787 mhz lol still air still vista 32 ^_^
http://valid.x86-secret.com/cache/banner/336661.png
http://img267.imageshack.us/img267/1003/478ag4.jpg
Got a Xeon 3110 today, but the temps reported under everest and coretemp are just out of this world. With 4.5Ghz@1.45volt the temps are around 80c, Idle around 49C. Is this normal or the diodes of this CPU are broken?