All good now
http://img524.imageshack.us/img524/4...erestbeta1.png
Printable View
Please a question...What is the best to overclocking?...the 759 or 760?
I used a 759 and reach good performance
http://i44.tinypic.com/106njmr.jpg
But there are no way to be a good performance without at least PCI ex on 112
Are the 760 identical?...do i have to set 110 or more in PCI ex to get higger thar BCLK 235?
if somebody can help me with this question, cause my 759 dead...and my 760 comes so soon.
thanks and sorry the broken english
I owned both, I say 760 is still a crazy clocker. it can bench @244bclkX17 on air, 3D06 passed. ;)Quote:
Originally Posted by rbuass
http://img40.imageshack.us/img40/759...clkx173d06.jpg
yep, you also need 110~112 to achieve high bclk.
+1 on 760 though I'm still learning the board
http://img.techpowerup.org/090622/5258GHz.jpg
Omg!!!
thanks for their suport friends...i will try with my new 760....i hope it get higher :)
what kind of VTT are most using with the classified. Can some one confirm that +250 to +400 it is in fact ok and not overvolting it. I thought that we should not use more than 1.45v on the vtt. What is the starting value on this MB ?
in e-leet with +250 reads 1.58v.
Thanks
I believe starting point is 1.2v. It also seems like E-leet monitoring shows higher than actual? Have to get out the volt meter and check. lol
edit, just checked with volt meter. Bios VTT=1.425 measured with volt meter = 1.425v E-leet 1.58v
The voltages in eleet are really screwy dimm voltage and QPI are way off, best to check with a dmm and if your using Elpida Hypers keep a close eye on dimm voltage have seen in another thread alot of dead hypers and i've gone through 2 sets myself.Quote:
Originally Posted by hlonipha
[QUOTE=bluehaze;3864802]The voltages in eleet are really screwy dimm voltage and QPI are way off, best to check with a dmm and if your using Elpida Hypers keep a close eye on dimm voltage have seen in another thread alot of dead hypers and i've gone through 2 sets myself.[/QUOTE
testing my new W3520.Went to 4.3 ht on 20 run linx with 1.31vcore and +150 vtt. what is your VTT setting ?
Haven't tried 4.5 HT yet got caught up trying to break 3dmark vantage 30k single card! Sooo close but can't do it! http://service.futuremark.com/compare?3dmv=1173268 need to find some tweaks for vantage.Quote:
Originally Posted by hlonipha
Anyways usually only +50vtt just to be safe for 4.2-4.5 i think it would run with +0 vtt though. Only time I know I have to raise vtt is for 4.6 have to raise vtt to compensate for the bclk to +125.
Thanks,Quote:
Originally Posted by bluehaze
Does this board support crossfireX, or should I say I have a 4870x2 that I would be using on the board when I get it. I might go to a gtx 295 or the new 5870x2, although I am wondering if the ATI cards will work with this board, I am not finding much info on this topic online. Anyone running ATI cards on the classified please speak up.
[QUOTE=Jakethesnake011;3870264]Does this board support crossfireX, or should I say I have a 4870x2 that I would be using on the board when I get it. I might go to a gtx 295 or the new 5870x2, although I am wondering if the ATI cards will work with this board, I am not finding much info on this topic online. Anyone running ATI cards on the classified please speak up.[/QUOT
The ATI cards are supported.
Of course it does support crossfire if you go to futuremark ORB to search....;)Quote:
Originally Posted by Jakethesnake011
Here is my setup:
http://img205.imageshack.us/img205/2253/setupm.jpg
http://img209.imageshack.us/img209/3...838default.jpg
Thanks I wanted to make sure before I bought one.
Diference in readings for my classified 760
http://img359.imageshack.us/img359/9...reswithdmm.jpg
Hi, I got my EVGA Classified and I have a problem with it :-( When i turn it ON, on POST-LED display lights "FF" and MoBo do nothing. CPU,RAM, VGA, PSU is OK -> tested on a different MB. I Tried CMOS reset in fron and in back, put out the battery. I realy donīt know, what to do. Please hepl me...
hloniphaQuote:
Originally Posted by hlonipha
you have 2 GTX 295 Evga on your 760 ? : confused:
I thought he should have a Evga 759 ..
you are in Sli ? not in Quad ?
there is there a big difference?
EVGA Classified 760 S60V
W352O 21X211 HT Enable @ 1.42V 3850A823
CORSAIR DOMINATORS GT @ 7-8-7-20 1T
PCP&C SILENCERŪ 910
2x EVGA GTX 295 SLI
X-Fi Fatal1ty Titanium PCI-E
1 x WD VELOCIRAPTOR 300
Seagate 1TB
CM HAF 932
HK 3.0/MCP655/FESER X360/Microres V2
Windows 7 64bit
Dell 3008WFP 30"
Try one stick of ram in the red ram slot nearest the cpu. If that doesn't work then try next stick of ram you have then final.Quote:
Originally Posted by BAGR_001
I have 2 GTX 295 in Quad SLI. I have a 760. Here is a link for the EVGA 760 specs http://www.evga.com/products/moreInf...ly=Motherboard FamilyQuote:
Originally Posted by hitachi974
lol you are confused cause I did not list list the word Quad on my sig????? cmon man
It does not work. Still the same error. RAMs are OK. I Tested it on the different MB.Quote:
Originally Posted by The Nemesis
RMA my friend!!!! I had problems with my first Classified. take a look at the pins in the cpu socket. if 1 pin is bent the system will not boot.Quote:
Originally Posted by BAGR_001
i dont like the new bios incase any of you guys are wondering...
infact i think i still love the original bios that came with my 759.
Is it good if my 920 D0 2D benches 3.15GHz @ 1vcore?
I'm doing some pretesting on my new 920 D0 and Classified. Just going quick prime 95 session right now.
http://i292.photobucket.com/albums/m...6-30090437.png
3.0GHz with 0.964vcore and all the other volts are at stock or under stock.
Which bios is that naekuh? bios version I mean you are using?Quote:
Originally Posted by NaeKuh
Bios Version : S21TQuote:
Originally Posted by bustamove44
BIOS Date : 6/11/2009
Bios File : E759S21T.bin (Primary Download Link)
i mostly updated because of this:
Updated CPU Microcode
I thought it would help the W3580 and W3570.
The update made me lose my OC @ voltage, i need to bump voltage to hold same OC.
Just did 3.2GHz with the same settings as before :)
http://i292.photobucket.com/albums/m...6-30101121.png
So do I have a alright chip?
EDIT:
Well heres my 4.0GHz - 4.1GHz shots, I know I didn't run prime long, i'll run it for longer so other time. I really hate it cause its so boring.
http://i292.photobucket.com/albums/m...6-30143113.png
http://i292.photobucket.com/albums/m...6-30144634.png
Yeah, same here. I cannot make the same OC stable under S21T as it was under S21S beta.Quote:
Originally Posted by NaeKuh
On a positive note, finished installing my new WC system in the Antec 900 :D Who says you cannot fit two 320s inside this case :p: I'll post pics later.
Temps are 69C using full LinX load at 4.21GHz with fans at 100% (3 Ultra Kaze 3K RPM sandwiched between two MCR320s). Ambient temp is extremely high here though, 29C - 30C today. Idle to load change is roughly 25C. I think I can be low 60s or below with normal ambient temps.
Happy 4th of July!!!!:D I would agree with the latest bios T, it s**ks. S21S is much more stable. On another note, has anyone ever seen the error code A7 on the Debug LED Display & know what it means?:shrug:
I have seen this A7 a couples of times on E760@S610 BIOS. Don't know its meaning though.Quote:
Originally Posted by Expat GriZ
it means your qpi signal setting is not liked at the settings you saved, try a different setting.Quote:
Originally Posted by raptord
Just got this board, gotta say its running very smooth, took me 10 mins to get 4.2ghz stable, best x58 board yet, good job evga! :clap:
Any update on new BIOS work? It would be nice to get a version that finally makes the SmartFan smart ;)
That and I am not sure what introduced instability into OCs in S21T, but simply reverting to S21S makes everything stable again...strange...
classified noob joining in
started off a bit funny hahahah
first boot no disaply on LED, after a bit of messing around and pulling one 8pin plug i get it too boot but stock on code 68 now.............oh crap
at the end had to reseat the CPU and that got it going
had to plug the second 8pin on a different spot on the back of the HX1000 to get it going with dual 8pins
in case someone else experienced that try reseating the CPU and RAM
(tip for the slow ones like me hahaha)
What is the normal boot code out of interest.
Alot of boards are picky about the amount of pressure/bowing created by the cpu mounting hardware too. If you run into no boot again, try loosening things a bit before removing.Quote:
Originally Posted by dinos22
Typically F3--> F6--> 68--> 69 --> C1 --> ? ? ?25--> 26 post sound and screen appears.Quote:
Originally Posted by clone38
What is code 26, mine hangs at 26 a lot and I have to hit the reset button then it will boot... :shrug:
are you guys finding that enabling/disabling turbo mode in bios is a bit weird
i have similar behaviour with original bios and S610 i just flashed to
however the new bios clocks bus a bit easier from what i can see now
? ? ? = C3Quote:
Originally Posted by The Nemesis
then 2d :cool:Quote:
Originally Posted by Anth Seebel
i think.
does the same thing to me, usually only when im running phase and high clocks. That or it will just cycle f3-f6 f3-f6, then I will hit restart and it will either boot or go to FF and not post so I power down and power up and the settings will work :rofl: not a huge deal to me now that I know it does that sometimes and how to fix itQuote:
Originally Posted by road-runner
Mine hangs randomly sometimes too I'll reboot and it will hang, I think it's at 26 then have to power it off then it will hang with FF then power it off then it will hang with CF then power off again not positive on the order but after the last time it will finally boot and say the OC is messed up but you go into bios and hit save without changing anything and then it boots fine. That's with 12 hours prime stable too...Quote:
Originally Posted by road-runner
^^^mine does a similar thing to this I dont get 'oc failed' though, it will hang on reboot on 26 or 68 press reset and it boots again and stable, weird. its a minor glitch, I can live with.
someone knows that this jumper? classified e-760
CSC Strap jumper I-LIMIT
DRACO - by the Shaminos email, it turning OFF Turbo Boost mode for good. It hepls stability under LN2 ... little bit.
I have my new "760" model and is little bit better then my "759". On first run, 220 MHz BLCK booted to Windows, max BCLK 235 MHz is good for initial test. W3540 SuperPi 4,9 GHz + 3DMark Vantage 4,7 GHz and CPUz Validation 4,94 GHz ... everything on AIR. By me, is "760" better then older model ...
Not sure if it correlates with the Classified brother, but I get the same cycle when pushing my memory too hard on the E758 board. Just a thought.:shrug:Quote:
Originally Posted by Bobbylite
So how much extra speed has the Classified been giving you guys?
Oh yeah and does this board resume from S3 well?
hello to all :)
I have just updated my DFI DK X58 + 920 D0 to classified + 950
problem is that it was too hard for me to rich 225 BCLK, what was too easy to do on DK, it was just needed to change VTT core..
first time I thought that it was CPU problem, replace to 920 D0 but the same...
So.. does enyone have the same CPU MB combination here??? and can anyone help with settings?? :)
Classified 790
intel core i7 950
STT PC 12800 7-7-7-24
Some ATI HD 4800 series cards :)
TOPOWER POWERBIRD 1100W PSU
here is my pure settings :)
CPU Vcore - 1.51-1.52
VTT - +250
IOCH - 1.32
here is some test results....
http://s58.radikal.ru/i159/0907/bd/8b2b425b22ba.jpg
http://s41.radikal.ru/i094/0907/ec/c6521c9125fc.jpg
http://s50.radikal.ru/i128/0907/3b/ae18f3ba4913.jpg
http://s47.radikal.ru/i116/0907/06/75989a3a3dfb.jpg
http://s47.radikal.ru/i116/0907/06/75989a3a3dfb.jpg
http://i023.radikal.ru/0907/4e/92835b85daee.jpg
have u tried
setiings
'less'
'less/middle'
and ~ 217 bclk boot with say 106 pcie and then up bclk with eleet?
give more on ioh man and qpi pll, like 1.45, 1.40v
@ master shamino
is it possible to add better memory overclocking with 2:10 mem multi in classified?
i couldn't run 2200mhz+ on classified with 2:10 whatever voltage i choose in vtt & vdimm.
in bloodrage i could run my mems at almost 2300mhz cas8.
i don't have money to buy good mems that's why i want better memory overclocking in 2:10 mem multi :)
thanks in advance! :up:
Quote:
Originally Posted by LardArse
yes I have tryed till 1.5 on IOCH but the same...
I was booting on 218 BCLK and after using eleet... max was 230 BCLK on 23 multy, afte crush....
so I am looking for more stable settings... I am shure that for validation 5.5 is possible and 5.45 for PI...
important is that my chip can boot on -107 ant has no any bug on -113..
all this test ebove is under LN2....
1.45 vcore
1.675 IOH/ICH I/O
1.45 ICH Vcore 1.05
1.45 QPI PLL 1.1
1.8 IOH PLL vcore 1.8
1.8
1.45 IOH Vcore 1.1
1.375 CPU VTT
1.7 DRAM
I'm still trying to figure this board out because I get better runs @ 4.9GHz than I do at 5GHz same voltages
http://img31.imageshack.us/img31/112...hzevgagtx2.jpg
and I cant rich more than 220 BCLK... :(Quote:
Originally Posted by TinTin
can u give me your write the settings u was using??
for me it's not working :(Quote:
Originally Posted by The Nemesis
QPI compensation have to set to "LESS"Quote:
Originally Posted by superhardware
pay attention to these voltages:
CPU VTT
QPI PLL voltage
IOH Voltage
IOH/ICH I/O Voltage
They will help you to achieve higher bclk. I can't say the exact figures, Because I have try 5pcs+ 920, 2 Xeon W3540, they are all different to these voltages~ ;)
BTW, what are your rams? Is it the ram holding the bclk? Some ram may do worse when using 2:8!
Quote:
Originally Posted by TinTin
RAM is SUPER TALLENT 1800MHz CL7, I have using the same rams on DFI, had never eny problem... and BCLK I had much more... :D
I have tryed with different voltage.. but it just dont post after 220 BCLK...
Have u tried lower multiplier and 220+ BCLK to elimante the cpu just not liking 23 or not capable of over 5GHz. Also you will need to increase skews. I need 300-500ps past 4.8Ghz on 920. Most of us boot @ 220BCLK. I did so even on a crappy X3540. I have cpu Impedance set to less and QPI compensation set to auto. I set VTT PWM Frequency & CPU PWM Frequency to 610 & 1200KHz
Max boot clock you can boot with classy is around 218-220.Quote:
Originally Posted by superhardware
boot it up and then use eleet or setfsb to push the bclk is the only way.
Posted this over in EVGA forums...
Been playing with some new WC lately and managed to get a nice setup going in my Antec 900. The two MCR320's from Swiftech are stacked sandwiching 3x3K RPM Ultra Kaze fans sucking air into the case from the front. Two DDC 3.2s in series are pushing the water around. Tubing is all 1/2" ID 3/4" OD Norprene (Tygon) tubing, and BP Black Sparkle fittings all around. Here are two pics of the setup...
http://img.techpowerup.org/090713/P7130209.jpg http://img.techpowerup.org/090713/P7130210.jpg
And here is the new 24/7 OC...21x212MHz (4.445GHz effective) HyperThreading On with Uncore at just over 4GHz and 1600MHz Corsair Dominator DRAM running at roughly 1690MHz OC using 7-8-7-17-59-1T timings and tighter DRAM Ratio (MCH Strap setting) subtimings. Ambient temperatures are 27C and fans for this run were at 55%. :up:
http://img.techpowerup.org/090713/21...X_20x_pass.jpg
Some cache and memory benchmarks...not bad for ~1690MHz DRAM ;)
http://img.techpowerup.org/090714/cachemem.png
And here is a 3DMark06 run using 4.5GHz clock, HT on, 2xHD4850 in CrossFireX clocked at 700/1175 on Vista x64 SP2...
27427 marks :D
http://service.futuremark.com/compare?3dm06=11453015
http://img.techpowerup.org/090714/3d...1_13072009.jpg
w3540 + e-760 + gskill perfec storn (elpida hyper) + Ss Rotary
http://img32.imageshack.us/img32/4292/imgp0104l.jpg
http://img196.imageshack.us/img196/9439/imgp0117b.jpg
http://img14.imageshack.us/img14/9243/245bkl.jpg
http://valid.canardpc.com/show_oc.php?id=603246
http://img12.imageshack.us/img12/9679/5300w3540.jpg
http://valid.canardpc.com/show_oc.php?id=603592
merci
Here is my issue, when i have all these cards plugged in, the board runs my top slot pci-e at 8x, so i can only have 3 cards in at the same time, if i have the x-fi at the top, gtx 295 in the proper 16x slots, it runs both slots at 16/16x, but if i have the xeno plugged in to the pci-e slot right under the 1st 16x slot, it takes down my slot to 8x, even tho xeno is only using 1x lane, is there any way to run the xeno as well as the x-fi and still have the gtx 295's running at 16x. Any help is appreciated. Below is a graph so you can see where i have the cards plugged in, thanks in advance.
http://img35.imageshack.us/img35/8034/e760.jpg
simple, just pull out th NIC card .:p:
This is a very silly question, but I would like to know your opinions.
Im oing to buy my first 1366 motheroard, I the ones I like the most were DFI UT X58 and this one, the Classified monster jaja.
Well My doubt its simple, and silly may be. With the sata3 behind the door<and also usb 3.0, does evga said someting about any upgrade or so for this mot, because<I dont know how convinient would be now buy a 500+uss motherboard where Im when it has their days in countdown... what you think?
Please... dont hit me:p
:slap:Quote:
Originally Posted by Osterman
It is a very good board. Current hardware does not even saturate sata3 and usb 3.0 is not adopted by anyone yet in the production sense. Hence, you are wasting your time worrying about that. This board will long be obsolete anyway before either something better than sata3 is needed or usb 3.0 is "the" standard.
There's no way for that, I dont even remember that X58 IOH(not ich) lanes can be strapped to 1x.Quote:
Originally Posted by GAR
Run some 3d tests with all cards in and test without Xeno and you'll see you lost nothing.
@cstkl1
http://www.abload.de/thumb/xeon4420-...52_7-8a9bd.jpg
You wanted someone with real stability - here I am ;)
More than 16h of Prime 64Bit using 5.5GB of RAM. It's rocksolid. Never seen a DFI doing that, mate! :D :up:
@superhardware : what your Bacth i7 950 ? look your chip very promising can run 5ghz on 3D vantage...any way nice result you get that bro..keep pushing....:up::up:
Yeah im going to pull it out, i got it free i thought i might as well use it, while using it TF2 "felt" smoother, could have been my mind :shrug:Quote:
Originally Posted by LardArse
Just disable it with the jumper, it saves me a lot of time.Quote:
Originally Posted by GAR
I think I may have messed up my Classified, and I think Matt (rdrash) screwed his up the same way last week. Both of us experienced almost the exact same symptoms...very short into a benching session (less than 5 min for me), the system locked up during a wPrime32M run. The board has not booted since...all I get is FF post code.
Matt's experience was almost identical...within about 10 minutes of his session, he locked up during a wPrime32M run, and he has mot posted with the board since. He is also only able to get a FF post code.
I was very curious about this strange situation, and I started looking for similarities in our setup. Both of us were running on LN2, and both of us were running wPrime32M. Both of us were running Elpida Hyper mem (6GB for Matt, 3GB for me). I was running a W3580 ES, he was running a i7 960 ES.
Then something caught my eye...both of use were using two high amperage 60x38mm fans to cool our mem...both of use were running them off the mobo's headers. I was running Deltas rated at 1.2A...his stuff is not accessible right now, so we have not been able to verify his...but I'm pretty sure they are similar to mine.
So I was looking at this thread on the eVGA forums:
http://www.evga.com/forums/tm.asp?m=100563466
and noticed the OP says that the max current draw for each header is 1.0-1.2A Looks like that may have been the problem for both of us.
So my questions are:
Do you think this is the cause of the problem?
And, is there a way I fix it?
Thanks :)
pro was getting FF a bit but it goes back up. one session it wouldnt but it started working next day so that was good i guess heh
my FF would is not a problem cause a powerdown and powerup gets it going again
hope you sort it out mate :up: and get some adapters for those fans to run off the PSU direct :p::p:
What...no jokes about me killing mobos :p:Quote:
Originally Posted by dinos22
:rofl::rofl::rofl::rofl:Quote:
Originally Posted by miahallen
i know what the problem is...... :rofl: :up:
on a lighter note
i am really starting to like my board
if she can repeat this with a 25xmulti now that would be nice :D
http://img401.imageshack.us/img401/7...t32msuperp.png
maxmem will stabilise at even higher clocks ;) but i dont think my chip has the legs to run that high on LN2 :)
i can only imagine how high 2:12 or higher ratio will clock this RAM.....scary :banana::banana::banana::banana: hehehe
very nice Dino :toast:
very nice run dinos! :DQuote:
Originally Posted by dinos22
is it the right voltage you use to run that mems at 2:10? (E-Leet)
why the cpu pll vcore is edited?
what's the correct value you set in bios with that cpu pll vcore?
thanks! :up:
sorry to hear that man, where's jake your buddy when u need him? :p:Quote:
Originally Posted by miahallen
can u try opening up the bios rom cage, press down hard on the rom dont let go and power up doing that?>
i dont know why but my board is acting a bit odd when it comes to CPU PLLQuote:
Originally Posted by DJSUB
when i flip that xcool switch thing selecting 1.8v in bios still results in 1.35v which is normal apparently but i switched it back to default position and i still get 1.335v on dmm and it shows nothing in windows :rofl:
havent seen anyone take screens with a volt blanked out like that
i dont care though
the board works ok lol
btw all the volts are checked with DMM :)
why do you ask?
ROFLQuote:
Originally Posted by LardArse
i remember now
it was the magic "press down hard on bios chip" trick for youngpro as well :rofl:
Quote:
Originally Posted by LardArse
What are you laughing at...it worked :DQuote:
Originally Posted by dinos22
Thank you Peter :yepp: I have no idea why, but it worked :up:
ah nice
good to see man :up:
Should be included in the manual :)
Hey people! I have a few question. Im going to buy a Classified but I have doubt in wich one I should buy, the 760 or the 759? I know the principal difference is that the 759 has de NF200, but there are any other differences? Wich would be the best for OC and in your personal experience wich one gives you the best result and less troubles in general?
Also... a Prolimatech Megahalems can fit in?
Thanks for all! When I get the mother I will post some results :)
PD: Sorry for my bad english.
What Different 759 & 761 ?
Having trouble getting my 920 stable at 4.3GHz.
It went real easy to 4.2GHz, but 4.3 has been a problem.
every time i up it to 4.3 it will prime for a couple of minutes, but every time i get a BOSD with the error "a cpu interrupt was not received on a second processor in the time allotted"
My max temp rages from 62 - 72 when stressed depending on the core.
I have tried upping the voltages a couple of notches, but no luck.
This is my first i7, so i am learning as i go. I figure there is something easy i am missing that is holding me back, any help would be appreciated.
I have tried upping the voltages to:
CPU Vcore = 1.2375
ICH Vcore = 1.1
QPI PLL = 1.2
IOH Vcore = 1.2
CPU VTT = 1.375
here is stable at 4.2GHz. (RAM is relaxed to eliminate any problems with it)
http://71.11.166.100:81/images/computer/4210_linx.png
Thanks,
http://www.pctunerup.com/up/results/...6_DSCN0592.jpg
COMING SOON....:D
Hello everyone... I've just about decided to get one of these boards, but I want to put it in my current case designed for standard size ATX boards. The classified is an EATX board but it appears it's just a bit bigger than standard ATX boards. Will the screw holes line up in the case assuming the board would physically fit?
Thanks,
Chris
What case do you have?Quote:
Originally Posted by Schlotkins
Can you explain why this fixes the FF problem?Quote:
Originally Posted by LardArse
if the bios rom is loose then it may noit be able to detect a bios romQuote:
Originally Posted by dejanh
Ahh, well, ok :doh:Quote:
Originally Posted by LardArse
I thought it was something more complicated than that ;) Why would it come lose like that all of a sudden if it worked before though, or I guess it could have just been fluke it did work before and eventually from moving and bumping the board it goes a bit loose.
By the way, do you have any updates on an upcoming BIOS?
i upped the cpu vcore to 1.2625 and VTT to 1.4. It no longer BOSD, but it still fails LinX.Quote:
Originally Posted by KaptainBlaZzed
I guess this means the chip just needs more volts.
There is quite a steep increase in volts from 4.2 to 4.3.
Does this happen on most i7s?
My D0 has an extremely steep increase in volts after ~4.2GHz. I can reach 4.2 with about ~1.27V but 4.473GHz requires ~1.4V at load to be LinX/Prime stable.Quote:
Originally Posted by KaptainBlaZzed
Whats going on? I'm due to receive my x58 Classified along with my i7 920 tommorrow and I've got a couple of questions...
First, will the red sata ports (or the ones that are on a separate controller) run a Raid array? are they bootable?
Second, and I've scoured the internets for an answer to this one, will this board run crossfire? I know x58s are supposed to sport both but EVERYWHERE i've read they only talks about 2 or 3 way SLI, or SLI + physx...I just need to know if that's a feature this board supports. It's going to be a minute before I can cough up the cash for some 285s and I need to know if I'm in for some disappointment when I plug in a couple of WCed 4870s tomorrow.
Thanks in advance for the answers...and KaptainBlazzed, nice etek in the sig, more of a DM/PM guy myself but regardless, not a bad setup. Dirty south means SE USA...played any CFOA?
On the first, I don't know for sure since I do not use those ports but yes at boot the JMicron controller tried to detect drives so I would guess whatever is connected there should be bootable.Quote:
Originally Posted by xXGearheadXx
On the second, yes, the board will run CrossFireX. I ran two 4850's on it just a few days ago for some testing. X58 natively supports CrossFireX.
Guys,
I have a 760 with a 920 C0/C1 chip (quite a cruel joke, btw - just bought it and quite some bad luck to get a C0. Didn't know importance of D0). Trying to get to 4.2 eventually, but at 4.0 for the moment and stable (IntelBurnTest maximum burn with many runs, superpi, benchmarks, etc.) except one thing - sometimes, like entering a game, a USB (such as my G15 keyboard) will disconnect and reconnect. This does not occur at stock. I suspect it could be due to one of my voltages being low. Please help me figure out which setting to adjust to stop this from happening, as it sounds like a slight bit of instability.
I filled out the template with all the settings just so you have all the information. Thanks for any help you can give on this issue!
Mother Board ( EVGA X58 Classified E-760)
Drivers (Newest from EVGA site)
Bios ( Newest from)
CPU ( 920 C0/C1)
CPU Cooler ( Cooler Master V10 )
Memory ( Corsair TR3X6G1600C9 XMS3 6 GB 3 X 2 GB)
PSU ( Corsair HX1000 )
GPU ( GTX295 )
Drivers ( 185.85 )
Operating System ( Windows XP 32-bit SP3 )
Frequency Control
CPU Clock Ratio ( 20X )
CPU Host Frequency (Mhz) ( 191 )
MCH Strap ( Auto )
CPU Uncore Frequency (Mhz) ( Auto )
CPU Clock Skew ( 0 ps )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 100 )
Memory Feature
Memory Speed ( Standard )
Memory Control Setting ( Enabled )
Memory Frequency ( 800Mhz / 2:6 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap ( Auto )
tCL Setting ( 9 )
tRCD Setting ( 9 )
tRP Setting ( 9 )
tRAS Setting ( 24 )
tRFC Setting ( 74 )
Command Rate ( 1t )
Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( 1.375 )
CPU VTT Voltage ( +150mV )
CPU PLL VCore ( Auto )
**IOH PLL VCore ( Auto )
DIMM Voltage ( 1.62V )
DIMM DQ Vref ( +0mV )
QPI PLL VCore ( Auto )
IOH VCore ( Auto )
IOH/ICH I/O Voltage ( Auto )
**VTT PWM Frequency ( 250 KHZ )
**CPU PWM Frequency ( 800 KHZ )
**CPU Impedance ( Auto )
**QPI Signal Compensation ( Auto )
ICH VCore ( Auto )
*PWM Frequency ( Not Used on Classified )
CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.800 GT/s )
OC Recorvery ( Disabled )