DFI Lanparty UT P45-T2RS Banter starts here!!!

Printable View

Show 100 post(s) from this thread on one page

12-02-2008, 08:15 AM
Kris

Quote:
Originally Posted by Kris View Post
Ran into some trouble.

I think I may have cooked the ram playing with some of C-N's voltage settings.

Update- Ram died! Old set passed. Oh well at least I had a spare set....
Sorry for your loss, The RAM is rated at 2.3v so it should have been alright but personally I would always use active cooling & I would have throttled the vdimm back as far as I could once I got the rig stable before pounding it with Prime95.

Now you've learnt the hard way, you wont do that again will you

I actually kept it @ 2.1 to 2.27. I think the ram might have been bad from the get go as I had so many issues when I first built the rig. To be honest I abused the crap out of my first set and they are still running strong.... As for active cooling I have a 150cfm delta pulling across the ram and enough 90 cfm fans in the case fans to blow the curtains in the window behind the case up the wall.:p:
12-02-2008, 06:25 PM
prostoman

Now I have tested different settings for Skews, and anything between 300 and 500 gives opportunity to boot at fsb498, while not possible otherwise. I also noticed that my core nr 1 and 4 are the strongest, while core nr 2 and 3 are weaker. So I have to sets of cores on the same level each. What I did was to try and change GTL values for cores in pairs. Ended up with GTL1:0.67, GTL2:0.63, GTL3: 0.63 and GTL4: 0.67. The result is: before, core 2 and 3 errored while priming at fsb495, after, all 4 cores priming with no errors. I still get random crashes and BSODs at fsb495 :(

Can anyone test if the things I mentioned in the last two posts work for you guys to get more stability on the edge? I still feel like there is no recepy for stable 500 on fsb, but I think I will use what I learned so far when going for higher CPU speeds :)
12-06-2008, 03:09 PM
Supershanks

Got my hands on the ddr3 version of this board DFI UT P45-T3RS some of the straps are a bit quirky but the 400 one rocks :)
First time i've got this far http://valid.canardpc.com/cache/banner/457234.png on a DFI ddr3 board.:up:
12-06-2008, 03:36 PM
prostoman

Quote:

Originally Posted by Supershanks

Got my hands on the ddr3 version of this board DFI UT P45-T3RS some of the straps are a bit quirky but the 400 one rocks :)
First time i've got this far http://valid.canardpc.com/cache/banner/457234.png on a DFI ddr3 board.:up:

Wow, not bad. Did you hit the wall yet? Or there is still some room for more? :)

It is about a week or more til I get to play with a E8600 in my board :(

Edit: Where did every one go? So quiet here lately.
12-07-2008, 06:11 PM
roedzzz

This is mine for fsb 600 x 7.5 Super PI 32M done just on air..

http://img247.imageshack.us/img247/2493/meexx9.jpg
12-08-2008, 12:53 AM
Supershanks

Quote:

Wow, not bad. Did you hit the wall yet? Or there is still some room for more?

It is about a week or more til I get to play with a E8600 in my board

I Hope not , CPU side seems to be clocking very easy. Waiting is always a pain , hope ya get a good one:up:

Nice one roedzzz :up:
12-08-2008, 05:23 AM
prostoman

roedzzz, getting my hopes up here, lol :)

Can you go higher? Looking at your ram my guess would be that it is hard enought as it is, hehe. I stand between 2GB of OCZ reaper 9200 and Flex 9200, dont know what to get for high fsb attempts. My 4GB stops at 1120MHz, and i dont want to push it.

Btw, I am sitting at bios version 10/07/2008. Is there a better bios that would give me an advantage of some sort? Or is there noe point in updating?
12-09-2008, 08:41 AM
Kris

Right now it appears that 10-07-08 is the only bios out.
12-09-2008, 08:49 AM
C-N

I posted a link on the 1st page of this thread to the final 1007 BIOS & the BETA BIOS 1028.

Linky... http://img.lanparty.tw/Upload/BIOS/CM/L245DA28.zip
12-09-2008, 10:03 PM
roedzzz

More result for 7.5 x 611 boot from bios..
But only done for PI 8M..my bad procie or RAM i think :(
For detil of my result you can see at chip.co.id

http://img224.imageshack.us/img224/7914/56361326ze6.jpg
12-09-2008, 10:51 PM
noinimod

What ram chips complement this board the best? I read that they're rather picky on rams..
12-09-2008, 11:02 PM
Kris

Quote:

Originally Posted by C-N

I posted a link on the 1st page of this thread to the final 1007 BIOS & the BETA BIOS 1028.

Linky... http://img.lanparty.tw/Upload/BIOS/CM/L245DA28.zip

Any major changes with this bios? I generally stay away from beta's.
12-09-2008, 11:22 PM
DavidNJ

Hi!...I am probably ordering mine tomorrow...just don't tell my wife.

Questions:

1) What is the best reference for the different BIOS settings. There are a lot of them, and each manufacturer seems to define them a little different.

2) Is the memory, which has an analog Buck converter, 1 phase or 2 phase?

3) Does the northbridge or power require any additional cooling? Do you need to move a lot of air in the case? My CPU and usually my video is watercooled.

I expect to run it with my Q6700, 4x2gb Corsair 1066 5-5-5-15 memory, and 1 or 2 1gb 4850 graphics cards. The CPU and the cards are watercooled with Dtek blocks and a Thermochill PA120.3, shroud, and 3 Noctua P12 fans. The rad is positioned sideways to give 1+ft clearance on either side.

Thanks in advance!
12-10-2008, 02:32 AM
C-N

Quote:

Originally Posted by noinimod

What ram chips complement this board the best? I read that they're rather picky on rams..

DFI Official memory support

Code:

Memory chip description Size Component Side A-DATA DDR II 1000 DDR II 1000 A-DATA 512 A-DATA M2OMIAG3H3160INC5Z Double 512 M2OMIAG3H3160INC5Z Double DDR II 1000 A-DATA 1024 A-DATA DDR2 1000 1GX16 Double 1024 DDR2 1000 1GX16 Double APOGEE GT DDR II 1100 DDR II 1100 APOGEE GT 1024 APOGEE AU1G632-11GP101 CL:555-15 Double 1024 AU1G632-11GP101 CL:555-15 Double Buffalo DDR II 1066 DDR II 1066 Buffalo 1024 Buffalo FSX1066D2C-K2G Double 1024 FSX1066D2C-K2G Double CELL SHOCK DDR II 800 DDR II 800 CELL SHOCK 1024 CELL SHOCK CELL SHOCK PC2-6400-1024 Double 1024 CELL SHOCK PC2-6400-1024 Double CERTIFIED By ATI DDR II 800 DDR II 800 CERTIFIED By ATI 1024 OCZ OCZ2A8002GK Double 1024 OCZ2A8002GK Double Corsair DDR II 1100 DDR II 1100 Corsair 1024 Corsair CM2X1024-8884D CL:444-12 Double 1024 CM2X1024-8884D CL:444-12 Double Crucial DDR II 1066 DDR II 1066 Crucial 1024 Crucial BL12864AL1065.8FE5 Double 1024 BL12864AL1065.8FE5 Double ELPIDA DDR II 800 DDR II 800 ELPIDA 2048 NCP Platinum ELPT8AUDR-25M88 Double 2048 Platinum ELPT8AUDR-25M88 Double DDR II 800 ELPIDA 512 EQUAL DDR II 800(5) 512M X16 Double 512 DDR II 800(5) 512M X16 Double G.SKILL DDR II 1000 DDR II 1000 G.SKILL 1024 G.SKILL F2-8000CL5D-2GBPI Double 1024 F2-8000CL5D-2GBPI Double DDR II 1000 G.SKILL 2048 G.SKILL F2-8000CL5D-4GBPI Double 2048 F2-8000CL5D-4GBPI Double DDR II 1000 G.SKILL 2048 G.SKILL F2-8000CL5D-4GBPQ Double 2048 F2-8000CL5D-4GBPQ Double DDR II 1000 G.SKILL 1024 G.SKILL F2-8000CL5D-2GBPK Double 1024 F2-8000CL5D-2GBPK Double DDR II 1066 DDR II 1066 G.SKILL 1024 G.SKILL F2-8500CL5D-2GBPI Double 1024 F2-8500CL5D-2GBPI Double DDR II 1066 G.SKILL 2048 G.SKILL F2-8500CL5D-4GBPI Double 2048 F2-8500CL5D-4GBPI Double DDR II 1066 G.SKILL 1024 G.SKILL F2-8500CL5D-2GBHK Single 1024 F2-8500CL5D-2GBHK Single DDR II 1066 G.SKILL 1024 G.SKILL F2-8500CL5D-4GBPK Double 1024 F2-8500CL5D-4GBPK Double DDR II 1066 G.SKILL 1024 G.SKILL F2-8500CL5D-2GBPK Single 1024 F2-8500CL5D-2GBPK Single DDR II 1066 G.SKILL 2048 G.SKILL F2-8500CL5D-4GBPK Double 2048 F2-8500CL5D-4GBPK Double DDR II 667 DDR II 667 G.SKILL 1024 G.SKILL F2-5300CL5S-1GBNJ Double 1024 F2-5300CL5S-1GBNJ Double DDR II 667 G.SKILL 2048 G.SKILL F2-5300CL4D-4GBPQ Double 2048 F2-5300CL4D-4GBPQ Double DDR II 667 G.SKILL 1024 G.SKILL F2-5400PHU2-2GBNT Single 1024 F2-5400PHU2-2GBNT Single DDR II 667 G.SKILL 2048 G.SKILL F2-5300CL5D-4GBMQ Double 2048 F2-5300CL5D-4GBMQ Double DDR II 800 DDR II 800 G.SKILL 1024 G.SKILL F2-6400CL5S-1GBNT Double 1024 F2-6400CL5S-1GBNT Double DDR II 800 G.SKILL 1024 G.SKILL F2-6400CL4D-2GBPI Double 1024 F2-6400CL4D-2GBPI Double DDR II 800 G.SKILL 2048 G.SKILL F2-6400CL5D-4GBPI Double 2048 F2-6400CL5D-4GBPI Double DDR II 800 G.SKILL 2048 G.SKILL F2-6400CL4D-4GBPI Double 2048 F2-6400CL4D-4GBPI Double DDR II 800 G.SKILL 1024 G.SKILL F2-6400CL4D-2GBPK Double 1024 F2-6400CL4D-2GBPK Double DDR II 800 G.SKILL 1024 G.SKILL F2-6400CL5Q-4GBNQ Double 1024 F2-6400CL5Q-4GBNQ Double DDR II 800 G.SKILL 2048 G.SKILL F2-6400CL4D-4GBPK Double 2048 F2-6400CL4D-4GBPK Double DDR II 800 G.SKILL 1024 G.SKILL F2-6400PHU2-2GBNR Double 1024 F2-6400PHU2-2GBNR Double DDR II 800 G.SKILL 1024 G.SKILL F2-6400CL5D-2GBNQ Single 1024 F2-6400CL5D-2GBNQ Single DDR II 800 G.SKILL 1024 G.SKILL F2-6400CL5D-4GBPQ Single 1024 F2-6400CL5D-4GBPQ Single DDR II 800 G.SKILL 2048 G.SKILL F2-6400CL6D-4GBMQ Double 2048 F2-6400CL6D-4GBMQ Double DDR II 800 G.SKILL 1024 G.SKILL F2-6400CL4D-2GBHK Single 1024 F2-6400CL4D-2GBHK Single DDR II 800 G.SKILL 1024 G.SKILL F2-6400PHU2-2GBHZ Single 1024 F2-6400PHU2-2GBHZ Single DDR II 800 G.SKILL 2048 G.SKILL F2-6400CL5D-4GBPQ Double 2048 F2-6400CL5D-4GBPQ Double DDR II 800 G.SKILL 2048 G.SKILL F2-6400CL5Q-8GBPQ Double 2048 F2-6400CL5Q-8GBPQ Double DDR II 800 G.SKILL 4096 G.SKILL F2-6400CL6Q-16GBMQ Double 4096 F2-6400CL6Q-16GBMQ Double DDR II 800 G.SKILL 4096 G.SKILL F2-6400CL6D-8GBMQ Double 4096 F2-6400CL6D-8GBMQ Double DDR II 800 G.SKILL 1024 G.SKILL F2-6400PHU2-2GBHZ Double 1024 F2-6400PHU2-2GBHZ Double GEIL DDR II 1066 DDR II 1066 GEIL 2048 GEIL GE24GB1066C5DC Double 2048 GE24GB1066C5DC Double DDR II 1066 GEIL 1024 GEIL GX22GB8500PDC Double 1024 GX22GB8500PDC Double DDR II 667 DDR II 667 GEIL 2048 GEIL Geil Black Dragon PC2-5300 Double 2048 Geil Black Dragon PC2-5300 Double DDR II 667 GEIL 2048 GEIL Geil2GBPC2-5300 Double 2048 Geil2GBPC2-5300 Double DDR II 800 DDR II 800 GEIL 1024 GEIL GX22GB6400UDC Double 1024 GX22GB6400UDC Double HYPER DDR II 1000 DDR II 1000 HYPER 512 Kingston KHX8000D2/1G Double 512 KHX8000D2/1G Double DDR II 1066 DDR II 1066 HYPER 512 Kingston KHX8500D2K2/1G Single 512 KHX8500D2K2/1G Single DDR II 1150 DDR II 1150 HYPER 1024 Kingston KHX9200D2/1G Double 1024 KHX9200D2/1G Double DDR II 800 DDR II 800 HYPER 512 Kingston KHX6400D2LLK2/1GN Single 512 KHX6400D2LLK2/1GN Single DDR II 800 HYPER 1024 Kingston KHX6400D2LLK2/2GN Double 1024 KHX6400D2LLK2/2GN Double Hynix DDR II 667 DDR II 667 Hynix 2048 NCP Platinum HYNT8AUDR-30M88 Double 2048 Platinum HYNT8AUDR-30M88 Double DDR II 800 DDR II 800 Hynix 2048 NCP Platinum HYNT8AUDR-30M88 Double 2048 Platinum HYNT8AUDR-30M88 Double Hyper DDR II 1066 DDR II 1066 Hyper 1024 Kingston KHX8500D2K2/2G Double 1024 KHX8500D2K2/2G Double DDR II 800 DDR II 800 Hyper 1024 Kingston KHX6400D2LLK2/1G Double 1024 KHX6400D2LLK2/1G Double DDR II 800 Hyper 2048 Kingston KHX6400D2K2/4G Double 2048 KHX6400D2K2/4G Double Kingston DDR II 667 DDR II 667 Kingston 2048 Kingston KVR667D2N5/2G Double 2048 KVR667D2N5/2G Double DDR II 667 Kingston 1024 Kingston KVR667D2N5/1G Double 1024 KVR667D2N5/1G Double DDR II 667 Kingston 512 Kingston KVR667D2N5/512 Single 512 KVR667D2N5/512 Single DDR II 800 DDR II 800 Kingston 2048 Kingston KVR800D2N/2G Double 2048 KVR800D2N/2G Double DDR II 800 Kingston 1024 Kingston KVR800D2N6/1G Double 1024 KVR800D2N6/1G Double DDR II 800 Kingston 2048 Kingston KVR800D2N6/2G Double 2048 KVR800D2N6/2G Double DDR II 800 Kingston 1024 Kingston KVR800D2N5/1G Double 1024 KVR800D2N5/1G Double MKX22D64M28G-25 DDR II 800 DDR II 800 MKX22D64M28G-25 1024 Mushkin EB2-6400655512-2GD Double 1024 EB2-6400655512-2GD Double Micon DDR II 1000 DDR II 1000 Micon 1024 A-DATA M2OMIAG3H3160INC5Z Double 1024 M2OMIAG3H3160INC5Z Double DDR II 1000 Micon 512 A-DATA M2OMIAG3H3160INC5Z DDR2 1000+ single 512 M2OMIAG3H3160INC5Z DDR2 1000+ single DDR II 1200 DDR II 1200 Micon 1024 Team Group TXDD1024M1200HC5 CL:555-15 Double 1024 TXDD1024M1200HC5 CL:555-15 Double Mushkin DDR II 1000 DDR II 1000 Mushkin 1024 Mushkin TXPR2-8000-45411-2GD CL:454-11 Double 1024 TXPR2-8000-45411-2GD CL:454-11 Double DDR II 800 DDR II 800 Mushkin 1024 Mushkin EB2-6400-55512-2GD Double 1024 EB2-6400-55512-2GD Double NCP DDR II 800 DDR II 800 NCP 1024 NCP NCPT7AUDR-25M48 Double 1024 NCPT7AUDR-25M48 Double OCZ DDR II 1000 DDR II 1000 OCZ 1024 OCZ OCZ2TA1000VX22GK Double 1024 OCZ2TA1000VX22GK Double DDR II 1066 DDR II 1066 OCZ 1024 OCZ OCZ2N1066SR2GK Double 1024 OCZ2N1066SR2GK Double DDR II 1066 OCZ 2048 OCZ OCZ2RPR10664GK Double 2048 OCZ2RPR10664GK Double DDR II 1150 DDR II 1150 OCZ 1024 OCZ OCZ2FX11502GK Double 1024 OCZ2FX11502GK Double DDR II 800 DDR II 800 OCZ 1024 OCZ OCZ2A8002GK Double 1024 OCZ2A8002GK Double DDR II 800 OCZ 1024 OCZ OCZ2G800R22GK Double 1024 OCZ2G800R22GK Double PATRIOT DDR II 1066 DDR II 1066 PATRIOT 1024 PATRIOT PVS22G8500ELK Double 1024 PVS22G8500ELK Double DDR II 1066 PATRIOT 2048 PATRIOT PVS24G8500ELK Double 2048 PVS24G8500ELK Double DDR II 1066 PATRIOT 512 PATRIOT PDC21G8500ELK Single 512 PDC21G8500ELK Single DDR II 800 DDR II 800 PATRIOT 512 PATRIOT PSD251280081/512 Single 512 PSD251280081/512 Single PQI DDR II 1066 DDR II 1066 PQI 2048 PQI PQI28500-4096DB Double 2048 PQI28500-4096DB Double Platinum Edition DDR II 800 DDR II 800 Platinum Edition 1024 OCZ DDR II 800 1GB CL444-15 Double 1024 DDR II 800 1GB CL444-15 Double Samsung - K4TIGQ84QA DDR II 667 DDR II 667 Samsung - K4TIGQ84QA 2048 Transcend TS256MLQ64V6U DDRII 667 Double 2048 TS256MLQ64V6U DDRII 667 Double Titanium Alpha DDR II 1000 DDR II 1000 Titanium Alpha 1024 OCZ DDR II 1000 1GB CL444-15 Double 1024 DDR II 1000 1GB CL444-15 Double DDR II 1120 DDR II 1120 Titanium Alpha 1024 OCZ DDR II 1120 1GB CL555-15 Double 1024 DDR II 1120 1GB CL555-15 Double Vitesta DDR II 667 DDR II 667 Vitesta 1024 ADATA DDR II 667(5) 1G X16 Double 1024 DDR II 667(5) 1G X16 Double XMS DDR II 800 DDR II 800 XMS 1024 Corsair CM2X1024-6400PRO CL5 Double 1024 CM2X1024-6400PRO CL5 Double XMS2 DDR II 1066 DDR II 1066 XMS2 512 Corsair CM2X512-8500 CL5 Single 512 CM2X512-8500 CL5 Single DDR II 1066 XMS2 1024 Corsair CM2X1024-8500C5 CL5 Double 1024 CM2X1024-8500C5 CL5 Double DDR II 667 DDR II 667 XMS2 512 Corsair CM2X512-5400C4 CL4 Single 512 CM2X512-5400C4 CL4 Single DDR II 800 DDR II 800 XMS2 1024 Corsair CM2X1024-6400C4 Double 1024 CM2X1024-6400C4 Double XTREEM DDR II 1000 DDR II 1000 XTREEM 1024 Teamgroup TXDD1024M1000HC5 Double 1024 TXDD1024M1000HC5 Double DDR II 800 DDR II 800 XTREEM 512 Teamgroup TXDD512M800HC4 Single 512 TXDD512M800HC4 Single DDR II 800 XTREEM 1024 Teamgroup TXDD1024M800HC4 Double 1024 TXDD1024M800HC4 Double XTUNE DDR II 1066 DDR II 1066 XTUNE 1024 AENEON PC28500U-555-12 CL:555-12 Double 1024 PC28500U-555-12 CL:555-12 Double DDR II 1142 DDR II 1142 XTUNE 1024 AENEON AXT760UD00-18DB98X Double 1024 AXT760UD00-18DB98X Double DDR II 800 DDR II 800 XTUNE 1024 AENEON AXT760UD00-25CC97X Double 1024 AXT760UD00-25CC97X Double kingston DDR II 667 DDR II 667 kingston 512 Kingston KVR667D2N5/512 Single 512 KVR667D2N5/512 Single DDR II 667 kingston 1024 Kingston KVR667D2N5/1G Double 1024 KVR667D2N5/1G Double mushkin DDR II 800 DDR II 800 mushkin 512 Mushkin EM2-6400-55512-1GD Single 512 EM2-6400-55512-1GD Single DDR II 800 mushkin 1024 Mushkin EM2-6400-55512-2GD Double 1024 EM2-6400-55512-2GD Double DDR II 800 mushkin 512 Mushkin THP2-6400-45411-1GD Single 512 THP2-6400-45411-1GD Single DDR II 800 mushkin 1024 Mushkin THP2-6400-45411-2GD Double 1024 THP2-6400-45411-2GD Double

Quote:

Originally Posted by Kris

Any major changes with this bios? I generally stay away from beta's.

1028 BETA

Major Reasons of Change:
Fixed PCIE 4,2 Slot X4 , X1 issue

Quote:

Originally Posted by DavidNJ

Hi!...I am probably ordering mine tomorrow...just don't tell my wife.

Questions:

1) What is the best reference for the different BIOS settings. There are a lot of them, and each manufacturer seems to define them a little different.

DFI official overclocking guide: http://img.lanparty.tw/Upload/Catalo...t/UTP45_OC.pdf

DFI Official BIOS guide: http://img.lanparty.tw/Upload/Catalo...45T2R_BIOS.pdf

Quote:

2) Is the memory, which has an analog Buck converter, 1 phase or 2 phase?

Honestly don't know, Is it important?

I would ask over at the official DFI support forum, someone over there will know. If you find out don't forget to let us all know here please.

Quote:

3) Does the northbridge or power require any additional cooling? Do you need to move a lot of air in the case? My CPU and usually my video is watercooled.

Personally I would say if you are going to OC it then I would but stock ish should be fine without. I have a slow quiet fan on both my NB & PWM & the temps are kept in the low 40's with both my dual core & quad core.

I also always cool my RAM, HD's & have a couple case fans going so 2 more make no difference to me.
12-10-2008, 04:42 PM
Crossbone

I've been playing around with this board for a few weeks now, and while there were (still are to be honest) some parameters I don't understand nor know what they pertain to, I've got a pretty good handle on the board itself and have gotten my old, yet reliable Q6600 to 3.6.

I'm still aiming for the 3.87 I was able to get on the X38 (Maximus Formula), but one thing I've noticed is in order to get the same frequencies achieved on the X38 on the P45 requires a bit more voltage.

Is it just me, or has anyone else noticed this as well?
12-11-2008, 03:12 PM
PolRoger

I've been struggling with this board today... and I've been getting plenty of "C1" messages on the LED display after a failed overclock attempts. Does anyone know what that means?
12-11-2008, 03:15 PM
Jor3lBR

Quote:

Originally Posted by PolRoger

I've been struggling with this board today... and I've been getting plenty of "C1" messages on the LED display after a failed overclock attempts. Does anyone know what that means?

In my experience: Insufficient Memory and/or North Bridge volts :up:
12-12-2008, 12:34 PM
prostoman

I have been getting plenty of C1 errors myself over the times. C1 is usually memory related, either your memory is over the limit, or NB is on the limit. Talking both from experience, and what I red at DFI forum.
12-12-2008, 12:54 PM
PolRoger

Thanks guys,

That info should be helpful when I get back on this board.
12-12-2008, 05:34 PM
DavidNJ

I should be getting my board on Monday. I expect to run it with a Q6700 and 8gb of Corsair 5-5-5-15 DDR 1066 memory.

Would one of you nice posters want to volunteer a good initial setup? The processor has run 10x360 on a motherboard that wouldn't run over 360 reliably, not even 6x365. The memory has been very finicky above 1066; however that may be a function of memory power stability.

Recomendations?

Thanks in advance!

P.S. The CPU and eventually the GPU will be water cooled. If necessary, the power circuit, northbridge, and southbridge could also be watercooled. It will have a 1000w PSU, probably a Corsair, maybe a Cooler Master, depending on which case it ends up in.
12-15-2008, 06:33 PM
Crossbone

This board is being a stubborn pain in my arse, I can get 3.6 stable, but I have yet to get anything else stable. I know for a fact my quad is capable of 3.87 @ 1.5125v, although as recent procedures have proven that would equate to 1.53-something on this board...but nonetheless it's finnicky about the settings used and I'm running low on patience...

Not really, but I am getting annoyed having to restart and bump up a specific parameter every five minutes. Anyone have any luck with this board using a quad?

Edit: Another thing, anyone know if two blocks I brought for the Maximus Formula awhile back (when it worked) will fit on this board? It appears to line up but I really don't feel like taking the board out and measuring just to have wasted time.
12-15-2008, 07:19 PM
SNiiPE_DoGG

just got my testbench going with the T3RS, subzero ambient water benches incoming ;)
12-16-2008, 12:30 AM
SNiiPE_DoGG

Hey guys quick update here:

the T3RS here has some pretty good abilities from what I have seen so far. ONE BIG problem though: NONE of the ram straps work whatsoever on release BIOS. the only ram strap that works above 1333 is AUTO lol. You might say "but isn't auto one of the selectable straps?" well yes and no, it appears to be the same as 333/1333 strap however, if you have a working prime stable setup with auto ram strap and you change it to manual 333/1333 strap you get the dreaded C1 :(. Even the working auto strap is very finicky and has limited me to 425-428FSB depending on latencies, at 429 it wont work and I have tried jumping around above that number as CAS 10 and an x7 multi with no luck whatsoever

Tomorrow I am going to try the beta bios and we will see if they have managed to make a DDR3 bios with strats that actually WORK!

for only 425 FSB and CR2 this board handles itself quite nicely (PL7), need to bring up the copy somehow
http://img124.imageshack.us/img124/1...est1700hg6.jpg
12-16-2008, 01:07 AM
C-N

Quote:

Originally Posted by Crossbone

This board is being a stubborn pain in my arse, Anyone have any luck with this board using a quad?

My Q9650 runs just as well on my DK as it does on my LT, 470 ~ 485fsb is about its prime max depending on how much tweaking you want to do.

Gotta love the slightly out of context quote ay.... :D

Quote:

Originally Posted by SNiiPE_DoGG

for only 425 FSB and CR2 this board handles itself quite nicely (PL7), need to bring up the copy somehow
http://img124.imageshack.us/img124/1...est1700hg6.jpg

looks good & I'm sure once you find some fsb the copy will come up.
12-16-2008, 04:37 PM
DavidNJ

I've seen people display very neat lists of the BIOS settings. How do they get them? Is their a utility that prints them?
12-16-2008, 05:03 PM
prostoman

1 Attachment(s)

Finally, I got the goods. But there are always problems, always something in the way. Missing a DVI/VGA converter and only have a stock cooler that is almost sitting there because of its own weight. Cant get it in place because I cant remove the backplate from my water setup (super strong glue back there)

Still, I got good results with temps goin no higher than 75'C and really cramped space and getto solutions for a lot of problems (will take a oic some day, lol)

I am not finished yet, and I know this will kick ass under water when I get back home after holidays (on the move with all the parts right now) 5GHz is with in my reach
12-17-2008, 01:13 AM
SNiiPE_DoGG

Went to beta BIOS and got a nice surprise :)

4.325 -- 480x9 and shes got plenty more where that came from ;)
1.376vCore
http://valid.canardpc.com/show_oc.php?id=464589
12-17-2008, 02:18 PM
SOXX

Hello,

the DFI is a very nice board. I test a Q9550 at FSB 470, it was very hard to be stable. FSB 500 is to heavy at the moment!

FSB 470 looks very nice:

http://www.abload.de/thumb/q95501248v10haztp.jpg

Can anyone give my Tips for get FSB 500 stable?

Sorry for my bad english, i leave the scool for 10 years ago :D!
12-17-2008, 02:22 PM
SNiiPE_DoGG

raise your vtt voltage to ~1.35 and you will reach higher FSB
12-17-2008, 02:27 PM
SOXX

I test it this weekend, VTT 1,35 is very high.

Anyone know when DFI release a new Bios?
12-17-2008, 02:42 PM
SNiiPE_DoGG

Quote:

Originally Posted by SOXX

I test it this weekend, VTT 1,35 is very high.

Anyone know when DFI release a new Bios?

not really at all. some run up to 1.5vtt 24/7

I dont believe it to be dangerous. I've been benching this weekend with 1.55VTT
12-17-2008, 02:48 PM
SOXX

OK, i will test it. My rig runs 24/7 with the settings in the screen, I think thats a very nice result.
12-17-2008, 04:38 PM
emoners

anybody tried running crossfire on this board? i've seen a lot of people running crossfire on the JR counterpart, maybe this board can do better?
12-17-2008, 04:45 PM
SNiiPE_DoGG

Quote:

Originally Posted by emoners

anybody tried running crossfire on this board? i've seen a lot of people running crossfire on the JR counterpart, maybe this board can do better?

I'm doing 4870x2 + 4870 512mb benching as we speak :D

heres the first result http://service.futuremark.com/compare?3dm06=9268247
12-17-2008, 04:49 PM
emoners

thanks SNiiPE_DoGG...any issues with that combo (4870x2 + 4870)? which lanes are you using by the way?
12-17-2008, 04:49 PM
SNiiPE_DoGG

Quote:

Originally Posted by emoners

thanks SNiiPE_DoGG...any issues with that combo (4870x2 + 4870)? which lanes are you using by the way?

using 8x8, havent played games on the test bench so I cant say if theres an issue
12-17-2008, 05:26 PM
SNiiPE_DoGG

heres the vantage trifire result, I pleased with it and I havent even voltmodded the x2 yet :shocked:

http://service.futuremark.com/compare?3dmv=604646
12-17-2008, 09:36 PM
zsamz_

Quote:

Originally Posted by SNiiPE_DoGG

I'm doing 4870x2 + 4870 512mb benching as we speak :D

heres the first result http://service.futuremark.com/compare?3dm06=9268247

nice
does it perform close to 3 4870s ?
you sick makin me wanna do trifire:rofl:
12-17-2008, 09:38 PM
SNiiPE_DoGG

Quote:

Originally Posted by zsamz_

nice
does it perform close to 3 4870s ?
you sick makin me wanna do trifire:rofl:

never used 3 4870s so I dont have a comparison, I can tell you though that the trifire is extra broken in extreme vantage preset, I only scored x5950 lololol:rofl:
12-17-2008, 10:06 PM
DoObs

Hey guys

Is it worth selling my Biostar I45 and getting the DFI LP DK P45-T2RS(ABS) Intel P45 Chipset OR if i can, get the DFI LP UT P45-T2RS
12-18-2008, 01:06 AM
emoners

@SNiiPE_DoGG: what's your settings on that Quad?
12-18-2008, 06:42 AM
SNiiPE_DoGG

Quote:

Originally Posted by emoners

@SNiiPE_DoGG: what's your settings on that Quad?

I'll get you a full bios template in like ~4 hours :up:
12-18-2008, 06:49 AM
Gogeta

Are these boards still being sold in the US? I'm not seeing any results for the UT variant on Froogle and Newegg has deactivated their listing. :(

Edit: Referring to the T2RS. I remember similar activity with retail inventory when the X48/X38-T2R were released. Hopefully this is the same deal.
12-18-2008, 08:10 AM
SNiiPE_DoGG

Quote:

Originally Posted by Gogeta

Are these boards still being sold in the US? I'm not seeing any results for the UT variant on Froogle and Newegg has deactivated their listing. :(

very odd. I bought mine last week.....

You might want to call motherboard pro and ask them, they definitely will have the inside scoop on this situation.
12-18-2008, 08:29 AM
SNiiPE_DoGG

Full BIOS template for the beta bios on the
P45 T3RS

Note: not fully prime stable, 3D and OCCT 1hr stable

Code:

>CPU Feature: Thermal Management Control.......... - Disabled PPM(EIST) Mode...................... - Disabled Limit CPUID MaxVal.................. - Disabled CIE Function........................ - Disabled Execute Disable Bit................. - Enabled Virtualization Technology........... - Enabled Core Multi-Processing............... - Enabled >DRAM Timing: Enhance Data transmitting........... - Fast Enhance Addressing.................. - Fast T2 Dispatch......................... - Disabled >Clock Setting Fine Delay Press Enter: DLL And RCOMP Settings.............. - Manual Ch1 Dram Defaul Skew................ - Model 1 Ch2 Dram Defaul Skew................ - Model 1 RCOMP Settings...................... - Model 1 Fine Delay Step Degree.............. - 70ps Ch1 Clock Crossing Setting.......... - Agressive DIMM1 Clock Fine Delay.............. - Current[1346ps] DIMM2 Clock Fine Delay.............. - Current[1346ps] Ch1 Control0 Fine Delay............. - Current[166ps] Ch1 Control1 Fine Delay............. - Current[166ps] Ch1 Control2 Fine Delay............. - Current[124ps] Ch1 Control3 Fine Delay............. - Current[110ps] Ch1 Command Fine Delay.............. - Current[262ps] Ch2 Clock Crossing Setting.......... - Agressive DIMM3 Clock Fine Delay.............. - Current[1346s] DIMM4 Clock Fine Delay.............. - Current[1346ps] Ch2 Control0 Fine Delay............. - Current[14ps] Ch2 Control1 Fine Delay............. - Current[56ps] Ch2 Control2 Fine Delay............. - Current[0ps] Ch2 Control3 Fine Delay............. - Current[0ps] Ch2 Command Fine Delay.............. - Current[110ps] Ch1 Ch2 Common Clock Setting........ - Auto Ch1 RDCAS GNT-Chip Delay............ - Auto Ch1 WRCAS GNT-Chip Delay............ - Auto Ch1 Command To CS Delay............. - Auto . Ch2 RDCAS GNT-Chip Delay............ - Auto Ch2 WRCAS GNT-Chip Delay............ - Auto Ch2 Command To CS Delay............. - Auto Flex Memory Mode..................... - Auto Common CMD to CS Timing.............. - 2N CAS Latency Time (tCL)............... - 7 RAS# to CAS# Delay (tRCD)............ - 8 RAS# Precharge (tRP)................. - 8 Precharge Delay (tRAS)............... - 22 All Precharge to Act................. - Auto REF to ACT Delay (tRFC).............. - Auto Performance Level.................... - 8 >Read delay phase adjust Press Enter: Channel 1 Phase 0 Pull-In........... - Auto Channel 1 Phase 1 Pull-In........... - Auto Channel 1 Phase 2 Pull-In........... - Auto Channel 1 Phase 3 Pull-In........... - Auto Channel 1 Phase 4 Pull-In........... - Auto Channel 2 Phase 0 Pull-In........... - Auto Channel 2 Phase 1 Pull-In........... - Auto Channel 2 Phase 2 Pull-In........... - Auto Channel 2 Phase 3 Pull-In........... - Auto Channel 2 Phase 4 Pull-In........... - Auto Write to PRE Delay (tWR)............ - Auto Rank Write to Read (tWTR)........... - Auto ACT to ACT Delay (tRRD)............. -Auto Read to Write Delay (tRDWR)......... - Auto Ranks Write to Write (tWRWR)........ - Auto Ranks Read to Read (tRDRD).......... - Auto Ranks Write to Read (tWRRD)......... - Auto ALL PRE to Refresh.................. - Auto >Voltage Settings: CPU VID Control..................... - 1.25V CPU VID Special Add................. - Disabled CPU VID Special Add................. - 113.22% DRAM Voltage Control................ - 1.87v SB Core/CPU PLL Voltage............. - 1.75v NB Core Voltage..................... - 1.55v (1.47v actual) CPU VTT Voltage..................... - 1.58v Vcore Droop Control................. - Disabled Clockgen Voltage Control............ - 3.45v GTL+ Buffer Strength................ - Strong CPU GTL 0 REF Volt.................. - 0.6725 CPU GTL 2 REF Volt.................. - 0.6725 CPU GTL 1 REF Volt.................. - 0.6725 CPU GTL 3 REF Volt.................. - 0.6725 North Bridge GTL 0 REF Volt......... - 0.6750 North Bridge GTL 1 REF Volt......... - 0.6750 FSB Vref............................ - Auto Genie BIOS Settings: Exist Setup Shutdown................ - Mode 2 Exist Shutdown After AC loss........ - Enabled AC Shutdown Free.................... - Enabled O.C Clock Fail Retry Counter........ - 1 O.C Clock Fail CMOS Reloaded........ - Disabled CPU Clock Ratio..................... - 9 Target CPU Clock.................... - 3800 MHz CPU Clock........................... - 482 Boot Up Clock....................... - Auto CPU Clock Amplitude................. - 900mV CPU Clock0 Skew..................... - 100ps CPU Clock1 Skew..................... - 100ps DRAM Speed.......................... - 400/1066 Target DRAM Speed................... - 1284MHz PCIE Clock.......................... - 101mhz
12-18-2008, 02:00 PM
DavidNJ

How do you get that printout of BIOS settings?
12-18-2008, 02:23 PM
C-N

Quote:

Originally Posted by DavidNJ

How do you get that printout of BIOS settings?

You don't, its just made up in notepad.

Copy & paste the template into notepad & edit it with your settings.

Then to display them here on the thread type

[ code ] (without the spaces)

paste in your settings then type

[ /code ] (without the spaces)
12-19-2008, 06:37 AM
DavidNJ

Watercooled Motherboard?

EK has waterblocks for the northbridge, southbridge, and power circuits, allowing you to remove the stock components and water cool. The northbridge and CPU Buck converter appears to run hot.
12-19-2008, 10:16 AM
SNiiPE_DoGG

Quote:

Originally Posted by DavidNJ

EK has waterblocks for the northbridge, southbridge, and power circuits, allowing you to remove the stock components and water cool. The northbridge and CPU Buck converter appears to run hot.

I will be completely watercooling this board, pics will be in my worklog in a few days
12-19-2008, 10:36 AM
SOXX

My Board is complete under water!

http://www.abload.de/thumb/bs6.jpg87if.jpg http://www.abload.de/thumb/bs7.jpg0cjf.jpg http://www.abload.de/thumb/bs8.jpgsaus.jpg http://www.abload.de/thumb/bs9.jpg3fpp.jpg http://www.abload.de/thumb/bs10.jpgd4j5.jpg http://www.abload.de/thumb/bs11.jpgj8fo.jpg http://www.abload.de/thumb/bs12.jpgn08h.jpg

The set is made in Germany by Mips Computer!
12-19-2008, 01:13 PM
DoObs

Quote:

Originally Posted by SOXX

My Board is complete under water!The set is made in Germany by Mips Computer!

Lucky guy...i so want one of these boards again!!!!
12-19-2008, 01:46 PM
SOXX

I use the Waterblocks on the DFI P35, X38 and now on the P45. It was a future investment :)
12-20-2008, 01:15 AM
prostoman

Yeah, I used a Tt waterblock on my UT board, but now the backplate is stuck to the back of the board. There was some kind of superglue there. How do I remove it now :/
12-20-2008, 02:11 AM
DoObs

Use some nail varnish remover does the trick with superglue
12-20-2008, 11:18 PM
DavidNJ

How do you get the MIPS blocks in the US. So far, I've only seen the EK blocks.
12-21-2008, 08:20 AM
zampa

hy,

I used this board (ddr3) before 15 days , in ddr3 it run very good , this is my first DFI and i feel it great !
how much can i put in vNB ?

thanks,

soory for my english i'm french...

http://images2.hiboox.com/images/510...3516df4aaf.jpg
12-21-2008, 10:16 AM
SOXX

Quote:

Originally Posted by DavidNJ

How do you get the MIPS blocks in the US. So far, I've only seen the EK blocks.

I shop the Mips set in Germany, I´m home in Germany, EK is also a very good Waterblockbuilder!
12-21-2008, 12:55 PM
DavidNJ

The MIPS blocks are hard to find in the US. And expensive. The set of three EK blocks is around USD130.
12-21-2008, 01:05 PM
SNiiPE_DoGG

Quote:

Originally Posted by DavidNJ

The MIPS blocks are hard to find in the US. And expensive. The set of three EK blocks is around USD130.

except for the fact that WCing the southbridge is absolutely useless and a passive enzotech copper SB heatsink is more than enough to cool the ICH10R
12-22-2008, 06:07 AM
SOXX

A new Beta Bios in on the DFI Homepage for the DFI P45 T2Rs -> Link
12-22-2008, 06:59 AM
C-N

Quote:

Originally Posted by SOXX

A new Beta Bios in on the DFI Homepage for the DFI P45 T2Rs -> Link

:up: added to 1st page of this thread.

BETA 1028 Has been removed & 1007 is still the only official BIOS.
12-22-2008, 10:38 AM
SNiiPE_DoGG

ah and another beta for the T3RS as well! should have my machine up in a few days, I can wait to use this one as it should bring even more gains :) and from the description it looks like they fixed the problem where the vid special add did the wrong percentage that what you set. :up:
12-23-2008, 08:54 PM
DavidNJ

How did you set up the DRAM fine delay models?

Also, I have a configuration that runs for hours without issue on Prime95, but won't boot. Once in 5 times it boots 30Mhz lower, and I bump it with SetFSB. What have I done wrong?
12-27-2008, 04:41 AM
andrewmodus

Welcome. I went on this MoBo and Q9650, more recently, and the last two days trying to achieve stability 465 * 9, but occasionally I get a frozen screen in Prime95. I was not able to identify the cause and decided to come back.
My BIOS 12/12. I intend to start again with 445 * 9 and 2 * 1Gb sticks Cellshock and would like to get basic advice.
What BIOS settings should I play for 445\450*9?
CPU V.
NB V.
VTT V.
CPU GTLs
NB GTLs
FSB Vref
CPU Skews
DRAM Skews
CN, you have such a quad - I would be grateful for any help from you.
Thanks
12-27-2008, 05:52 AM
C-N

Quote:

Originally Posted by andrewmodus

Welcome. I went on this MoBo and Q9650, more recently, and the last two days trying to achieve stability 465 * 9, but occasionally I get a frozen screen in Prime95.

CN, you have such a quad - I would be grateful for any help from you.

I have a full list of settings a few pages back for 4.3GHz which might help you get a starting point.

I found the more VDIMM you throw at the board the further you can go without lockups. Also I had to tweak the below settings.

Clock Setting Fine Delay Press Enter:

DLL And RCOMP Settings.............. - By Menu
Ch1 Dram Default Skew................ - Model 6
Ch2 Dram Default Skew................ - Model 6
RCOMP Settings...................... - Model 1

Fine Delay Step Degree.............. - 100ps
12-27-2008, 10:47 AM
DavidNJ

Why set the fine delay step if you aren't manually setting the fine delays? I couldn't get my system to boot the 6/6/x combos. Could you post what the fine delays are for that model?

I am running 5/5/1 with the DRAM Skews set to 2100ps manual (30deg x 70ps adjustment). Lowly B3 Q6600. Passes 10+hours of Prime 95 @ 426fsb. Gets single cpu prime error after 1-8 hours at speeds 430-445, but will run 3DMark06 and appear to run without freezing at those speeds. Freezes at 450 and and higher.
12-27-2008, 11:31 AM
C-N

Quote:

Originally Posted by DavidNJ

Why set the fine delay step if you aren't manually setting the fine delays?

I did play with the step & fine delays manually & found simply increasing the step from 70 to 90/100 achieved the same stability as adjusting the delays manually.

Quote:

I couldn't get my system to boot the 6/6/x combos. Could you post what the fine delays are for that model?

It is ram specific I think as all my RAM kits require different settings, just play about & see what feels best for your setup.
12-27-2008, 11:49 AM
DavidNJ

I was wondering what the timings are for 6/6/1. After you reboot it displays the timings next to the 'current' label.
12-27-2008, 12:43 PM
kitfit1

Quote:

Originally Posted by C-N

It is ram specific I think as all my RAM kits require different settings, just play about & see what feels best for your setup.

Not only is it ram specific, but it can and will change depending on the NB voltage that is set as well.
12-28-2008, 12:43 AM
andrewmodus

My preliminary result
http://images.people.overclockers.ru/171530.png
I loved this MoBo!

CN, You just have freezing the screen?
You helped plant Skew 6-6-1?
At that affects FSB Vref? I installed 21.
12-28-2008, 12:47 AM
SNiiPE_DoGG

Quote:

Originally Posted by andrewmodus

My preliminary result
http://s39.radikal.ru/i084/0812/f5/9c7258ae64cbt.jpg
I loved this MoBo!

CN, You just have freezing the screen?
You helped plant Skew 6-6-1?
At that affects FSB Vref? I installed 21.

hey andrew, if your looking for a bit higher clocks the Q9650s love VTT voltage, set it up to 1.35-1.4 and see where that gets you. should be at least another 150mhz in my experience with the ddr3 version of this board. :up:
12-28-2008, 01:42 AM
C-N

Quote:

Originally Posted by kitfit1

Not only is it ram specific, but it can and will change depending on the NB voltage that is set as well.

Thanks for that kit, now you've said that it makes sense why throwing extra vNB at the rig sometimes resulted in worse stability. This could also explain why the board's would fail to boot at a certain vNB.

Quote:

Originally Posted by andrewmodus

My preliminary result
http://s39.radikal.ru/i084/0812/f5/9c7258ae64cbt.jpg
I loved this MoBo!

CN, You just have freezing the screen?
You helped plant Skew 6-6-1?
At that affects FSB Vref? I installed 21.

Whole PC locks up.

I tested all skew combinations & found every increase e.g. 3 ~ 4 then 4 ~ 5 helped me prime large/custom fft's further & further until I finally settled at 6-6-1. 7-7-1 did not help any more.

I tested all FSB Vref combinations & found they made no real noticeable difference to my rig, I would say leave it auto. My rig would only boot into windows using 00,2B,28,23 & 22 with the quad if it helps.
12-28-2008, 01:45 AM
C-N

Quote:

Originally Posted by DavidNJ

I was wondering what the timings are for 6/6/1. After you reboot it displays the timings next to the 'current' label.

I already posted them a few pages back.

http://www.xtremesystems.org/forums/...&postcount=257

CN :)
12-28-2008, 02:25 AM
andrewmodus

CN, which chips are you using? D9GKX?
12-28-2008, 03:00 AM
C-N

Quote:

Originally Posted by andrewmodus

CN, which chips are you using? D9GKX?

I am using this kit

http://www.ocztechnology.com/product..._ready_edition

They are the older GMH based 2.3v chips.
12-28-2008, 05:00 AM
DavidNJ

How do you determine which chips are in the memory?
12-28-2008, 05:35 AM
kitfit1

Quote:

Originally Posted by DavidNJ

How do you determine which chips are in the memory?

If you have a look here it will give you a good idea. That list is a bit old now, but if you are running anything there, then it is still valid. Of course if yours is newer, then it's also telling you that your IC's are newer.
12-28-2008, 05:45 AM
kitfit1

Quote:

Originally Posted by C-N

Thanks for that kit, now you've said that it makes sense why throwing extra vNB at the rig sometimes resulted in worse stability. This could also explain why the board's would fail to boot at a certain vNB.

That's my conclusion as well C-N. In fact, it should'nt come as a surprise really, because the UT P35 behaves in exactly the same way. For the 5.1ghz clock on my P35 the NB needs 1.53v, even one notch higher or lower and the cross clock settings change and the clock is then unstable. The UT P45 is the same, with the added complication of the Rcomp and Ram Skews to throw into the eqaution.

Who said clocking was easy :)
12-28-2008, 12:10 PM
andrewmodus

I'm still not found the cause of the freezing of the screen. This always happens in different ways - sometimes in the first 5 minutes Prime95, sometimes 30 minutes, sometimes I walk Small without problems.
This is a 455 * 9 or higher. SG is currently shows Vcore 1.26V, Vtt 1.31V, Vnb 1.29V.
I use all GTLs 0.67, CPU skew 200/100, DRAM Skew 3-3-1, FSB Vref 21, Vram 2.04V.
I can not understand what may be the cause of my problems.
12-28-2008, 02:58 PM
Shiranui Gen-An

Quote:

Originally Posted by kitfit1

Not only is it ram specific, but it can and will change depending on the NB voltage that is set as well.

Thanks for pointing that out, I don't think I would have noticed otherwise :up:
12-31-2008, 09:26 AM
SOXX

FSB 482x8,5 is stable now, it was a hard fight! Next projeckt 500x8,5

http://www.abload.de/thumb/q95501296v12h6h6g.jpg

A Happy New Year @ all
12-31-2008, 11:32 AM
DavidNJ

Interesting note...on testing with a Q6600B3. I could do 445x8 and run 3DMark06. 430x6 and run Prime95 for 6-8 hours. 426x8 and run Prime95 over 12 hours until I turned it off.

The same processor, video card, cooling, memory with a 780i, by far the best 780i of three I've had here, couldn't do it. 425 could run 3DMark06 but froze or rebooted in minutes on Prime95. The same for 365x9. In the end, the best I could do is 360x9 or 400x8. Both seem to pass Prime95 (the later still testing), but the first seems to produce a higher 3Mark06 value.

It seems the digital PWM was worth 160-200Mhz in CPU speed.

On both systems CPU VID reported by OCCT was similar. CPU VTT was set to the same value. CPU GTLs were set to the same values then fiddled on the 780 to see if it made a difference. The 780 didn't have a clock skew adjustment for CPU, NB, or memory. The 780 does have many more useful memory dividers and supports x16/x16 SLI.
01-03-2009, 11:17 AM
TheGanG

What are the key factors for E8600 @ 5.9-6.0 GHz 10*600 FSB with that mainboard? Thanks :)
01-03-2009, 12:13 PM
kitfit1

Quote:

Originally Posted by TheGanG

What are the key factors for E8600 @ 5.9-6.0 GHz 10*600 FSB with that mainboard? Thanks :)

Getting there ;)
01-03-2009, 12:22 PM
TheGanG

Quote:

Originally Posted by kitfit1

Getting there ;)

Sure, but with some BIOS options :rolleyes:
01-04-2009, 06:09 AM
kitfit1

Quote:

Originally Posted by TheGanG

Sure, but with some BIOS options :rolleyes:

I hav'nt bothered trying to get to 600+ fsb myself.........yet :). But i do know the mobo is capable of it because Rgone posted a suicide screenie at DFI club. The highest i've gone to at the moment is 563 fsb, but that is with 4x1g sticks of ram and it is'nt a suicide shot, it's 24/7 stable (see link in sig). If you look at the link in my sig, it should give you a good idea of settings you may need to move up towards 600+ fsb. Of course, 600x10 is'nt going to happen unless your under Dice or LN2. 600x9 though, should be more than doable under Phase.
01-05-2009, 07:59 AM
TheGanG

Quote:

Originally Posted by kitfit1

I hav'nt bothered trying to get to 600+ fsb myself.........yet :). But i do know the mobo is capable of it because Rgone posted a suicide screenie at DFI club. The highest i've gone to at the moment is 563 fsb, but that is with 4x1g sticks of ram and it is'nt a suicide shot, it's 24/7 stable (see link in sig). If you look at the link in my sig, it should give you a good idea of settings you may need to move up towards 600+ fsb. Of course, 600x10 is'nt going to happen unless your under Dice or LN2. 600x9 though, should be more than doable under Phase.

Thanks, i will check your settings. This will be my first DFi run. I got some 5.8 GHz results with BlackOps X48 under Dice-Pot. So i am sticky to my current Dice-Pot for a while...
01-06-2009, 06:22 AM
TheGanG

My first run was 570 FSB:

http://valid.canardpc.com/show_oc.php?id=478414

Updated BIOS and trying to understand P45. Second run will be 600+ FSB and 5.8+ GHz (if i can)

I have DFi Lanparty DK P45-T2RS Plus. Are they same boards, DFI Lanparty UT P45-T2RS Banter and mine? Same BIOS and same rulez? If not, is there anyone with DFi Lanparty DK P45-T2RS Plus? (sorry for too much posts)

Thanks...
01-06-2009, 06:32 AM
fellix_bg

I think there's plethora of other threads, dedicated to P45 DK boards. This one here is only for the UT model.
01-06-2009, 08:48 AM
C-N

Quote:

Originally Posted by TheGanG

I have DFi Lanparty DK P45-T2RS Plus. Are they same board, DFI Lanparty UT P45-T2RS Banter and mine? Same BIOS and same rulez? If not, is there anyone with DFi Lanparty DK P45-T2RS Plus there? (sorry for too much posts)

Thanks...

The BIOS is very similar & they play very similar.

I am subscribed here http://www.xtremesystems.org/forums/...d.php?t=191950 for the DK & Angoholic http://www.xtremesystems.org/forums/...&postcount=608 looks to be the man for fsb atm.

CN :)
01-06-2009, 10:23 AM
angoholic

:up: Would try the UT but i do not think you will get higher FSBs with Wolfdales, maybe someone has nice Quad Results with the UT >FSB510, max with the DK was FSB507@Prime Large stable which could be used for 24/7
01-08-2009, 02:13 AM
TheGanG

Thanks a lot, moved to DK thread ;)
01-09-2009, 02:47 PM
prostoman

2 Attachment(s)

4,9GHz easy! 5GHz= kinda hot
01-30-2009, 03:52 AM
spoof

So, any stable achievements with Q9550 with 480+FSB? I'm looking to change my X48 with P45 because of the low FSB for 24/7 and for benching. I'm choosing between LP UT P45-T2RS and Maximus II Formula. The main goal is 480 stable, because my CPU can do it ...
01-31-2009, 07:43 AM
SOXX

Look at this!

FSB 494x8,5 with Q9550, next step the Magic 500 :up:

http://www.abload.de/thumb/420012hcy9z.jpg
02-01-2009, 09:37 AM
rioja

Quote:

Originally Posted by SOXX

I use the Waterblocks on the DFI P35, X38 and now on the P45. It was a future investment :)

i may say u one more good thing - at least mips pwm block is compatible with dfi x58 :up:
i like such continuity of their lt/ut boards
02-04-2009, 09:18 AM
03hdfatboy

New here and fairly new to this Mobo. And I haven't seen anyone running the same CPU as me so I haven't had anyone to compare notes with.
http://i61.photobucket.com/albums/h63/03FATBOY/test.jpg
02-05-2009, 07:18 AM
DJSUB

my 2nd stability & Bandwith test with DFI Lanparty UT P45 T3RS :D

http://img11.imageshack.us/img11/415...utp45t3qg6.png
02-05-2009, 07:41 AM
Shiranui Gen-An

Quote:

Originally Posted by spoof

So, any stable achievements with Q9550 with 480+FSB? I'm looking to change my X48 with P45 because of the low FSB for 24/7 and for benching. I'm choosing between LP UT P45-T2RS and Maximus II Formula. The main goal is 480 stable, because my CPU can do it ...

Have you checked out the new Rampage Formula beta BIOS? It adds CPU and NB clock skew options, which can greatly assist in higher FSB clocking.
02-06-2009, 04:45 AM
mitkomk

What about new beta bios
Date Code 2009-01-12
File L245D112.exe
Size 842 KB
1. The BIOS enhanced the 16GB memory compatibility issue.
2. The BIOS Improved DRAM O.C. function.
http://www.dfi.com.tw/portal/CM/cmpr...rmal&mode=view

Show 100 post(s) from this thread on one page