My problem is the VTT, all under 1.55 - 1.6V > not stable !
Printable View
My problem is the VTT, all under 1.55 - 1.6V > not stable !
i sure hope you don't really mean vtt there.
cos vtt that high is guaranteed to kill your chip and fast.
i've only gone up to 1.52 for quick math benching at 8x540.
What Ram could you guys recommend me to use on this board?
This good ram for it:
G.Skill 4GB (2x2048MB) DDR2 PC2 8800 CL5 4 GB, PC8800, 1111 MHz
Or do you have other suggestions? (i want 4GB)
HeheQuote:
Originally Posted by Gautam
My QX9650 like the UD3P too :)
http://img147.imageshack.us/img147/1...0cpuvalpe5.jpg
sweet! post the ET6 for that clock?
do you need voltages anywhere near my 1.7pll, 1.5vtt, 1.47vcore, and 1.8vnb?
Yea, love to see the setting s for that run.
I have tried all these different settings and suggestions but still no go past 425, that is weak. It looks like I got a bunk board. I have an RMA number already but I cannot ship out until I get paid in like a week. I am hoping dor a primo cream of the crop board next time, well aren't we all.
Hey did any quad user succesfully using S3 mode with this board at 400 fsb and above ?:confused:
I mean no constant reboot in in infinite loop with a blank screen when wake the system up.
More isnt possible :
http://www.abload.de/thumb/settings2ci5p.jpg
What a bad board :/
In 2 - 3 days i have a new GA-EP45-UD3R ... lets see .....
ok, see that number next to "MCH Core"?Quote:
Originally Posted by slash777
you need more of it.
I cant more than 1.40V because at this voltage >>> FreezeQuote:
Originally Posted by Slovnaft
From know on I love this Board!
All results on AIR!!!
1M
http://www.abload.de/thumb/1m25ke.jpg
32M
http://www.abload.de/thumb/32mf265.jpg
Vantage
http://service.futuremark.com/compare?3dmv=507443
Mark06
http://service.futuremark.com/compare?3dm06=8804750
Prime with 4250 on AIR!!!
Q9550 | 4250MHz | 1.408v | FSB500 | DDR2-500MHz | Gigabyte UD3P | LuKό | L835A730 | T | 1,25v | emertX
http://www.abload.de/thumb/unbenannt4jp10.jpg
lol niceQuote:
Originally Posted by Gautam
i dont get the board
i did some testi last night again and no matter what i try i cant get any decent FSB to stick
leaving on auto voltages allows me to boot at 620 even but as soon as it gets a whiff of the HDD it bombs out or corrupts my bootmngr
i have tried practically all combinations of skews i could think of and nothing is working...that is the only other thing that i can thing of not helping
i've played with reference VTT as well but no go
just not having luck
swapped boards to EP45 EXTREME and on first go
http://img412.imageshack.us/img412/5...pionairmf6.png
:shrug:
could it be the bios i am on........i'm on the F4Pi bios (bios is called F4-4 bios as well..)
has anyone else noticed that VTT Reference volts dont seem to change in Easy Tune6
Could that be the issue
Test the F5
Hey guys
Got myself a ud3r yesterday, but only managed a 600mhz 1m. Any tips wrt the clock skews? 550 isn't even 32m stable :(
Also, F4 bios was AWFUL so I switched back to F3.
Thanks
Mike
http://valid.x86-secret.com/show_oc.php?id=443671
http://www.abload.de/img/459ghztrd103k60.jpg
if anyone needs settings you find lots of mine at the ud3p thread in the intel hardware section.
The Bios from UD3R is very buggy .....Quote:
Originally Posted by I34z1k
It's a crazy board for the memory frequency .
I can't post actually because there's a contest.
For the quad it's the best if you've got good memory .
First play with this board
BIOS - F4
Crucial Ballistix Tracer - 2.4V
CPU & NB H2O cooled
wPrime v1.55
http://img.photobucket.com/albums/v3..._545fsb_wp.jpg
Everest scaling w/PL level - How low can we go? :p
PL 11
http://img.photobucket.com/albums/v3...erest_pl11.jpg
PL10
http://img.photobucket.com/albums/v3...verest_pl1.jpg
PL9
http://img.photobucket.com/albums/v3...verest_pl9.jpg
PL8
http://img.photobucket.com/albums/v3...verest_pl8.jpg
I love this board!!!
Hey Guys, have a look at this!!!
On Air-Cooling! IFX-14!!!
Q9550 | 4352MHz | 1.456V | FSB-512MHz | DDR2-512MHz | Gigabyte UD3P | Air-Cooling | L835A730 | T | 1,25v | emertX
http://www.abload.de/thumb/unbenannt4350_2hya2.jpg
what is the best memory do you recommend for using the Q9550 ? I was thinking of the Dominator/ Tracers/ Ballistics [cheapest] or GSkill [which seems most compatible] or OCZ Reapers?.
get tracers dominators or ballistix, no need to pay extra
....(((these are my latest 24/7 setings for 4455mhz ran prime blend for hour,s with no errors while watching movies on you tube and downloading music on lime wire))).....Quote:
Originally Posted by ezaleina
GIGABYTE EP45-UD3R..INTEL E8400 E0 BATCH#Q829A103..CELLSHOCK D9GKX
ROBUST GRAFIX BOOST............TURBO
CPU CLOCK RATIO...................9X
CPU HOST FREQUENCY.............495
PERFORMNCE ENHANCE.............EXTREME
MCH FREQUENCY LATCH............333MHZ
SYSTEM MEM MULTI.................2.00B
NEXT YOUR RAM SETTINGS MINE RUN 4-4-4-10...SO SET YOURS TO RUN STABLE YOU MAY NEED SOMETHING LIKE 5-5-5-12
I SET MINE TO PERFORMANCE LEVEL 9 PL8 RESULTS IN INSTANT CRASH EVEN ON 1.2400 VCORE...I USED MEMSET TO LOWER A BUNCH OF MY SUB TIMINGS MOST OF IT CAN BE DONE IN THE BIOS BUT I LIKE IT CUZ I DONT HAVE TO KEEP REBOOTING TO FIND THE TIGHTEST SETTINGS FOR MY RAM,S..
LOAD LINE LLC.........................ENABLED
CPU V-CORE...........................1.37500V...you may need more..you may need less i can bench less but 1.37500V keeps it ROCK stable
CPU TERMINATION...................1.42000V..this is as low as i can set it to be ROCK stable unless i jack the CPU PLL up to like 1.5700V or more
CPU PLL.................................1.2500V
ICH I/O..................................1.2500v..((your board may need pll and ich l/O up to 1.3500v))
DRAM.....................................FIND WHAT DRAM SETING YOUR RAM NEEDS TO RUN AT 990MHZ
(((ALL OTHER SETTINGS AND VALUES ON AUTO))) AND THIS WILL MAKE FOR A FAST 24/7 RIG....but im still shooting for more ghz.:D ive benched 520x9 and ran 1m super a 10.000 flat or it was 530x9 i ran both but cant remember which one i ran super pi on...im going to try new skews to get stable over 500 with less then crazy volts..im a 24/7 kind of guy....bios f3 f4 and f4a beta seemed the same...these settings worked on all 3 bios,s for the UD3R it should work for the ud3p also but hey i could be wrong
Try F6d here
heres something to keep this thread goinghttp://i37.tinypic.com/e5puvk.jpg
Heey Hicookie the BIOS F4PI also worked with the same configuration on an E8500?;)
Has anyone tried a Q6600 in this board? See only Wolfdale/Yorkfield shots. :( :)
I'll be doing so in a week. I have to ship my Intel BadAxe2 mainboard overseas to relatives, and this board will be my replacement.Quote:
Originally Posted by joshua7
Also replacing the Crucial ram in sig with two G.Skil 4GB 4-4-4-12 @1.8-1.9v 4GB modules.
Looking forward to the test. :)Quote:
Originally Posted by LoneWolf
Hi friends. :cool:
I have a problem with the FSB of my Mother Board :confused:
this is my setup at the moment and I can not climb over the FSB.
any suggestions? :eek:Quote:
GIGABYTE GA-EP45-UD3P
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .................: [Auto]
CPU Clock Ratio .........................: 9
Fine CPU Clock Ratio.....................: [+0.0]
CPU Frequency ...........................: 4.68GHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled] [Disabled]
CPU Host Frequency (Mhz) ............: 520Mhz
PCI Express Frequency (Mhz) .........: [Auto]
C.I.A. 2.............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 700mv
PCI Express Clock Drive...................: 700mv
CPU Clock Skew (ps).......................: 0ps
MCH Clock Skew (ps).......................: 0ps
DRAM Performance Control
Performance Enhance....................: [Turbo]
Extreme Memory Profile (X.M.P.)........: [Disabled]
(G)MCH Frequency Latch.................: [Auto]
System Memory Multiplier ..............: 2.00B
Memory Frequency (Mhz) ................: 1040
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time...............................: 5
tRCD ..........................................: 5
tRP'...........................................: 5
tRAS...........................................: 15
Advanced Timing Control [Press Enter]
tRRD...........................................: 5
tWTR...........................................: 5
tWR............................................: 8
tRFC...........................................: 52
tRTP...........................................: 5
Command Rate (CMD) ............................: 2
Channel A
Channel A Timings Settings [Press Enter]
Static tRead Value......................: [Auto]
tRD Phase0 Adjustmen...................: [Auto]
tRD Phase1 Adjustment...................: [Auto]
tRD Phase2 Adjustment .................: [Auto]
tRD Phase3 Adjustment..................: [Auto]
Trd2rd(Different Rank)..................: [Auto]
Twr2wr(Different Rank)..................: [Auto]
Twr2rd(Different Rank)..................: [Auto]
Trd2wr(Same/Diff Rank)..................: [Auto]
Dimm1 Clock Skew Control................: [Auto]
Dimm2 Clock Skew Control................: [Auto]
DDR Write Training......................: [Disabled}
Channel A Driving Settings [Press Enter]
Driving Strength Profile:..............: [AUTO]
Data Driving Pull-Up Level.............: [Auto]
Cmd Driving Pull-Up Level..............: [Auto]
Ctrl Driving Pull-Up Level.............: [Auto]
Clk Driving Pull-Up Level..............: [Auto]
Data Driving Pull-Down Level...........: [Auto]
Cmd Driving Pull-Down Level............: [Auto]
Ctrl Driving Pull-Down Level...........: [Auto]
Clk Driving Pull-Down Level............: [Auto]
Channel B
Channel B Timings Settings [Press Enter]
Static tRead Value......................: [Auto]
tRD Phase0 Adjustmen...................: [Auto]
tRD Phase1 Adjustment...................: [Auto]
tRD Phase2 Adjustment .................: [Auto]
tRD Phase3 Adjustment..................: [Auto]
Trd2rd(Different Rank)..................: [Auto]
Twr2wr(Different Rank)..................: [Auto]
Twr2rd(Different Rank)..................: [Auto]
Trd2wr(Same/Diff Rank)..................: [Auto]
Dimm1 Clock Skew Control................: [Auto] ps
Dimm2 Clock Skew Control................: [Auto] ps
DDR Write Training......................: [Disabled}
Channel B Driving Settings [Press Enter]
Driving Strength Profile:..............: [AUTO]
Data Driving Pull-Up Level.............: [Auto]
Cmd Driving Pull-Up Level..............: [Auto]
Ctrl Driving Pull-Up Level.............: [Auto]
Clk Driving Pull-Up Level..............: [Auto]
Data Driving Pull-Down Level...........: [Auto]
Cmd Driving Pull-Down Level............: [Auto]
Ctrl Driving Pull-Down Level...........: [Auto]
Clk Driving Pull-Down Level............: [Auto]
Motherboard Voltage Control
Voltage Type. ... ... Normal
CPU
Load-Line Calibration....................: [Enabled]
CPU Vcore . .........1.22500V*.........: 1.4500
CPU Termination ...... 1.200V*...........: [Auto]
CPU PLL .........1.500V*...........:[Auto]
CPU Reference..........0.760V............: [Auto]
MCH/ICH
MCH Core ..........1.100V............: 1.400
MCH Reference.. ... . .0.760V............: [Auto]
MCH/DRAM Reference.....0.900V............: [Auto]
ICH I/O .... ......1.550V............: [Auto]
ICH Core...............1.100V............: [Auto]
DRAM
DRAM Voltage ........1.800V............: 2.32
DRAM Termination ... ..0.900V............: [Auto]
Channel A Address Vref 0.900V............: [Auto]
Channel B Address Vref 0.900V............: [Auto]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect.................: [Disabled]
CPU Enhanced Halt (C1E)...................: [Disabled]
C2/C2E State Support......................: [Disabled]
x C4/C4E State Support....................: [Disabled]
CPU Thermal Monitor 2(TM2) ...............: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology.................: [Disabled]
Note: * refers to 45nm CPU
whyQuote:
Originally Posted by emertX
do you know if it improves FSB
this thread name always makes me think WTF...how come not a single person yet has managed to get even close to hicookie's FSB :p:
CPU Vcore . .........1.22500V*.........: 1.4500Quote:
Originally Posted by Solid Snake
CPU Termination ...... 1.200V*...........: [Auto]
CPU PLL .........1.500V*...........:[Auto]
its simple to make you fly
65nm of intel processor, try CPU termination 1.4v
also, you need CPU PLL for 65nm processor, try 1.6~1.8v
45nm, just pull higher CPU termination, 1.32v(540FSB)~1.6v(600FSB & beyond)
i see you change memory ratio to match your memory, thats smart way:)
It took me awhile to get things set up, because at first, I experienced random reboots and instability.Quote:
Originally Posted by joshua7
I went back, disconnected all power/data cables and all cards, and removed/reseated the RAM. I also clipped the ends of two of my PSU's SATA connectors and replaced them with right-angle ones, and went with right-angle SATA data cables to remove kinks.
The system is now up and very stable, with a RAID 1 mirror for my boot drive, and a third 1TB drive for media storage, running the F5 BIOS. Since I had a Tuniq Tower, I also had to dremel the K8 "nipples" off the sides of the mounting clip so that it would fit well. I have only just reloaded the OS, and will be restoring data in the next 48 hours. I'm running at stock settings for now until I have everything set up just the way I want it; at that point, I'll consider doing a minor overclock to go up to 1333 FSB. Stock performance of the board is quite good, though.
Quote:
Originally Posted by LoneWolf
Any oc done since then? :)
I have and gotten a 515FSB and if I was better at tweaking clock skews i'm sure it would be better.Quote:
Originally Posted by joshua7
Sounds good. I still do not know whether to switch over. Probably I'll buy a new psu 1st, as during 3dmark06/Vantage cpu tests my rig just switches off. :) :(
i cant get 4.0 stable in orthos >_>
after 2 minutes error :(
(Easy tune6 are the same settings i have put in the bios)
http://i430.photobucket.com/albums/q...g?t=1234420385
i have enable line-calibration on bios
--
PC:
E8400 C0
Gigabyte EP45-UD3P Rev1.0 Bios F7 (official from gigabyte)
G.skill 2x2GB 8500C5
TT Toughpower 850w
Win XP SP3 with all the update from microsoft
Dunno if this will be of use but here are my settings for 530mhz 5:6 Stable - 500 Linpack Loops passed, 24 hours Prime95, 12 hours looping 3d06.
Note - this memory has problems running 1:1 ratio, it only likes the upclock dividers. Confirmed on biostar and gigabyte boards.
M/B: EP45-UD3R
CPU: E8500 E0
Memory: Kingston HyperX PC9200 2 x 1gb (Elpida)
GIGABYTE GA-EP45-UD3R
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .................: [TURBO]
CPU Clock Ratio .........................: 8.5x
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 530Mhz
PCI Express Frequency (Mhz) .........: [103]
C.I.A. 2.............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 700mv
PCI Express Clock Drive...................: 700mv
CPU Clock Skew (ps).......................: 200ps
MCH Clock Skew (ps).......................: 0ps
DRAM Performance Control
Performance Enhance....................: [Turbo]
(G)MCH Frequency Latch.................: [Auto]
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ................: 1272
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time...............................: 5
tRCD ..........................................: 5
tRP'...........................................: 4
tRAS...........................................: 15
Advanced Timing Control [Press Enter]
tRRD...........................................: 2
tWTR...........................................: 2
tWR............................................: 4
tRFC...........................................: 38
tRTP...........................................: 2
Command Rate (CMD) ............................: 2
Channel A
Channel A Timings Settings [Press Enter]
Static tRead Value......................: [9]
tRD Phase0 Adjustmen...................: [1-Advanced]
tRD Phase1 Adjustment...................: [1-Advanced]
tRD Phase2 Adjustment .................: [1-Advanced]
tRD Phase3 Adjustment..................: [1-Advanced]
Trd2rd(Different Rank)..................: [5]
Twr2wr(Different Rank)..................: [4]
Twr2rd(Different Rank)..................: [4]
Trd2wr(Same/Diff Rank)..................: [7]
Dimm1 Clock Skew Control................: [Auto]
Dimm2 Clock Skew Control................: [Auto]
DDR Write Training......................: [Enabled]
Channel A Driving Settings [Press Enter]
Driving Strength Profile:..............: [OC-1333]
Data Driving Pull-Up Level.............: [Auto]
Cmd Driving Pull-Up Level..............: [Auto]
Ctrl Driving Pull-Up Level.............: [Auto]
Clk Driving Pull-Up Level..............: [Auto]
Data Driving Pull-Down Level...........: [Auto]
Cmd Driving Pull-Down Level............: [Auto]
Ctrl Driving Pull-Down Level...........: [Auto]
Clk Driving Pull-Down Level............: [Auto]
Channel B
Channel B Timings Settings [Press Enter]
Static tRead Value......................: [9]
tRD Phase0 Adjustmen...................: [1-Advanced]
tRD Phase1 Adjustment...................: [1-Advanced]
tRD Phase2 Adjustment .................: [1-Advanced]
tRD Phase3 Adjustment..................: [1-Advanced]
Trd2rd(Different Rank)..................: [5]
Twr2wr(Different Rank)..................: [4]
Twr2rd(Different Rank)..................: [4]
Trd2wr(Same/Diff Rank)..................: [7]
Dimm1 Clock Skew Control................: [Auto] ps
Dimm2 Clock Skew Control................: [Auto] ps
DDR Write Training......................: [Enabled]
Channel B Driving Settings [Press Enter]
Driving Strength Profile:..............: [OC-1333]
Data Driving Pull-Up Level.............: [Auto]
Cmd Driving Pull-Up Level..............: [Auto]
Ctrl Driving Pull-Up Level.............: [Auto]
Clk Driving Pull-Up Level..............: [Auto]
Data Driving Pull-Down Level...........: [Auto]
Cmd Driving Pull-Down Level............: [Auto]
Ctrl Driving Pull-Down Level...........: [Auto]
Clk Driving Pull-Down Level............: [Auto]
Motherboard Voltage Control
Voltage Type. ... ... Normal
CPU Load-Line Calibration....................: [DISABLED]
CPU Vcore . .........1.22500V*.........: 1.4500
CPU Termination ...... 1.200V*...........: [1.220]
CPU PLL .........1.500V*...........:[1.500]
CPU Reference..........0.760V............: [0.757]
MCH/ICH
MCH Core ..........1.100V............: 1.300
MCH Reference.. ... . .0.760V............: [0.754]
MCH/DRAM Reference.....0.900V............: [1.070]
ICH I/O .... ......1.500V............: [1.500]
ICH Core...............1.100V............: [1.100]
DRAM
DRAM Voltage ........1.800V............: [2.14]
DRAM Termination ... ..0.900V............: [1.070]
Channel A Address Vref 0.900V............: [1.070]
Channel B Address Vref 0.900V............: [1.070]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect.................: [Enabled]
CPU Enhanced Halt (C1E)...................: [Disabled]
C2/C2E State Support......................: [Disabled]
x C4/C4E State Support....................: [Disabled]
CPU Thermal Monitor 2(TM2) ...............: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology.................: [Disabled]
Dymblos,i think maybe your mch ref voltage is too low(0.66),bring it up a few notches so it reads in ET6 as 0.70 to 0.76.start with 0.70 then try 0.74 and so on,till it works.also set your vMCH(NB voltage) to 1.30.good luck
here my setup with EP45-UD3P
fsb 675mhz
CPU on Dry Ice - 39:(
NB Stock
http://valid.canardpc.com/show_oc.php?id=507320
good board, i test with air cooled pushed manage 620MHz bench :up:
hi man, nice FSB, What Voltage do you use?Quote:
Originally Posted by nut311
regards
your cpu pll too low.Quote:
Originally Posted by Dymblos
i do a little test with minum voltage for 580MHz
CPU vcore: 1.200v
CPU PLL: 1.65v
CPU VTT: 1.20v
CPU / REF: 0.76v
RAM:2.0v
MCH: 1.30v
Super Pi 32M pending...
http://img248.imageshack.us/img248/3...032m001re7.png
Finish
http://img7.imageshack.us/img7/9972/...032m002rj6.png
continue doing priming test with FSB 580MHz
i add some voltages to make sure it could run 24hrs
here the voltage i add
Super PI 32M
CPU vcore: 1.200v
CPU PLL: 1.65v
CPU VTT: 1.20v
CPU / REF: 0.76v
RAM:2.0v
MCH: 1.30v
Burn-IN
CPU vcore: 1.200v
CPU PLL: 1.67v
CPU VTT: 1.22v
CPU / REF: 0.76v
RAM:2.0v
MCH: 1.32v
with low voltage prime 2 hours pass, and continue..
http://img207.imageshack.us/img207/9933/ud3p580pxe2.png
Quote:
Originally Posted by Solid Snake
i used VTT 1.60v, Vmch 1.58v CPU on DICE :) but i play MCH refrence for run 666MHz FSB Super PI 1M