Retail Q9650 Overclocking Thread

Printable View

Show 100 post(s) from this thread on one page

01-20-2009, 04:38 PM
orbiter

Quote:

Originally Posted by Jor3lBR

North bridge only needs a fan there, this board runs cooler then any other I had, probably the extra cooper.

I did all my runs on stock sinks on SB, NB, and Mosfets:
-Q9540@4095Mhz;
-Q9650@5005Mhz;
-Q9650@4400Mz on AIR;

Check my sig for results.

At what stage do I need have a fan on NB Jor3lBR? as for 24/7 use I'm hopefully going to run @ 4 - 4.1 Ghz. Also when using fan did you remove the blue heatsink cover over the NB?

Kind Regards

Orb
01-20-2009, 05:00 PM
Jor3lBR

Quote:

Originally Posted by orbiter

At what stage do I need have a fan on NB Jor3lBR? as for 24/7 use I'm hopefully going to run @ 4 - 4.1 Ghz. Also when using fan did you remove the blue heatsink cover over the NB?

Kind Regards

Orb

Hey Orbiter,

You wont need a fan to run 4 to 4.1Ghz, I would only use it for FSB's around 500 or above that.

If you don't wanna remove the original cover you can just buy 2 little CoolJags that have 18CFM in Push-Pull (side-by-side) 6v and you're fine!

If removing original heat sink (hot blow-dryer and lots of Patience) you will only need a 50 or 60mm fan on top.
01-20-2009, 05:05 PM
kill_a_wat

Quote:

Originally Posted by andressergio

Thanks mate :up:

Is PLL really helping you ? in my case i really don't see it effects...

Honestly PLL hasn't done much for me at all. I mainly up it a little if chasing more memory performance and see if it helps stabilise the system
01-20-2009, 05:44 PM
andressergio

Quote:

Originally Posted by kill_a_wat

Honestly PLL hasn't done much for me at all. I mainly up it a little if chasing more memory performance and see if it helps stabilise the system

Thank you, will try but seems that this quad needs more food, i runt a max stress using 3048MB IBT 10 run on 4185(465x9) mems 1200PL7 and gave me on last run different residual :( i don't know what can be causing that as mems passed overnight memtest.

Cheers
Sergio
01-20-2009, 06:07 PM
nugzo

1 Attachment(s)

Quote:

Originally Posted by orbiter

OK nice, Thanks nugzo.

You still have NB air cooled? and it's still ok at 4.5Ghz.

Kind Regards

Orb

I'm using Jor3lBR's 4400 template . I was 12hours Blend and 13hrs Small FFT with his settings. I bumped vtt, pll, mch and vcore all up 1 notch and ive been priming for 4 hours now @ 495FSB 4455MHz.

We should probably move this discussion over to the UD3 thread now.

Here is my NB cooling..
01-20-2009, 06:10 PM
systemviper

I found 503 qas my sweet spot on that board, I think in a week or so i will go back and see it could get it higher, that is just such a killer set up,.

nice work nugzo :up: plus that is a friggin sweet case!
01-21-2009, 06:37 AM
orbiter

Quote:

Originally Posted by Jor3lBR

Hey Orbiter,

You wont need a fan to run 4 to 4.1Ghz, I would only use it for FSB's around 500 or above that.

If you don't wanna remove the original cover you can just buy 2 little CoolJags that have 18CFM in Push-Pull (side-by-side) 6v and you're fine!

If removing original heat sink (hot blow-dryer and lots of Patience) you will only need a 50 or 60mm fan on top.

Ok Jor3lBR thank you :up:

Quote:

Originally Posted by nugzo

I'm using Jor3lBR's 4400 template . I was 12hours Blend and 13hrs Small FFT with his settings. I bumped vtt, pll, mch and vcore all up 1 notch and ive been priming for 4 hours now @ 495FSB 4455MHz.

We should probably move this discussion over to the UD3 thread now.

Here is my NB cooling..

Nice setup ya got there nugzo & very nice going on the OC too :yepp:

I Think I'd be more than happy with a quick test at 4.400GHz when I get mine, then for 24/7 I think around 4.0 - 4.2Ghz would be fine.

Orb
01-21-2009, 06:41 AM
radaja

very nice set up nugzo
01-21-2009, 09:05 AM
andressergio

Quote:

Originally Posted by nugzo

I'm using Jor3lBR's 4400 template . I was 12hours Blend and 13hrs Small FFT with his settings. I bumped vtt, pll, mch and vcore all up 1 notch and ive been priming for 4 hours now @ 495FSB 4455MHz.

We should probably move this discussion over to the UD3 thread now.

Here is my NB cooling..

very nice mate, seems like the gigabbyte clocks the Q9650 much better than the MF2...what vid is yours ? i can't get those clocks...

Cheers
Sergio
01-21-2009, 09:58 AM
kill_a_wat

Definetly the P45 when it comes to the higher clocks. But I haven't explored the other aspects of P45 vs other chipsets when it comes to performance eg. gaming performance, video card (8x8 vs 16x16) etc etc....

But for pure high clocks and bench runs possibly P45 is the king...

I wish I had a lower VID chip I'd definetly go for 4.5Ghz+ my RE can easily boot into Windows at 500x9

@ Sergio - I think you can definetly get your 470x9 just got to find those settings. I remember for me, it took a while to get 4.2 Ghz stable whilst <4.2Ghz was very quick. But my hat goes off to those with the not so good chipsets and 1.25VID chips and 4.2Ghz+ stable as I know there is quite some fiddling to do :)
01-21-2009, 10:02 AM
CryptiK

Very nice Nugzo that rig looks really good. I like the chipset cooling solution, that has to be a massive improvement over the standard heatsink. Any chance you can show us some benches I'd like to see what a quad at that speed and a GTX295 can do.
01-21-2009, 05:41 PM
mreld3r

new 9650

Ordered monday; received from newegg today.
q9650 Batch# L828a480
vid: 1.1000v (according to CoreTemp 0.99.3)
Running now stock on an MSI Neo2FR p35 motherboard (rev. 1) until paday when I will be ordering a UD3P.
CPU-z reports cpu volts @ 1.06 - 1.07 right now
Wish me luck, I hope I gotta good chip, because I spent a whole year with a crappy overclocker chip. I deserve a good one this time.
Anyone have any info on this batch #?
Thank you guys.
01-21-2009, 06:24 PM
Hoss331

I just got my 9650 in today also and so far is definitely looks to be better than my 9550. :) Idle and loaded temps are several degrees lower so hopefully its accurate. VID is 1.15 and batch is L827A945.
01-21-2009, 11:19 PM
radaja

just purchased my first intel quad core proccessor,so tommorrow me and my UD3P will be joining you guys here with our new friend Mr9650.hopefully we have as much fun as you guys are having
01-21-2009, 11:52 PM
WaterFlex

Quote:

Originally Posted by radaja

just purchased my first intel quad core proccessor,so tommorrow me and my UD3P will be joining you guys here with our new friend Mr9650.hopefully we have as much fun as you guys are having

Good luck:)
01-22-2009, 01:00 AM
EOD

I just got my Q9650 today from newegg. it is batch: L826A965 with 1.25v vid

4.2GHz (467 FSB * 9 multi) at 1.296v vcore at load (1.312 idle) and Running H2O.

http://valid.canardpc.com/show_oc.php?id=490072

I made sure I was ready for this chip. I spent the last few days tweaking my motherboard and (now old Q6700) for a stable 467 FSB OC. Once I got it dialed in, It was a matter of just stabilizing the vcore. So far I am just past 6Hrs stable in Prime95.

I have been considering going with a UD3P to see what this chip can really do...
01-22-2009, 01:56 AM
Hoss331

First attempt at 4ghz, this looks to be very promising.

http://i131.photobucket.com/albums/p...tmapImage2.jpg
01-22-2009, 02:25 AM
kill_a_wat

Quote:

Originally Posted by Hoss331

First attempt at 4ghz, this looks to be very promising.

http://i131.photobucket.com/albums/p...tmapImage2.jpg

Very nice dude. Very low vCore good chip!
01-22-2009, 02:52 AM
andressergio

Quote:

Originally Posted by kill_a_wat

@ Sergio - I think you can definetly get your 470x9 just got to find those settings. I remember for me, it took a while to get 4.2 Ghz stable whilst <4.2Ghz was very quick. But my hat goes off to those with the not so good chipsets and 1.25VID chips and 4.2Ghz+ stable as I know there is quite some fiddling to do :)

hey mate

I tried this settings and tested carefully

467 x 9 MEMS 1245 5-5-5-15-5-65-8-5

CPU Skews Normal - NB Skew delay 100
RAM SKEWS all channels on 100
NB GTL +40 /DDR REF +12,5 A/B
NB DDR REF -25
MEM OC Charger = disabled
STATIC READ = disabled
PL 7 / STRONGER

vcore set on bios 1,4
pll 1,526
vtt 1,4
nb 1,45
sb 1 1,55
sb 2 1.2

CPU GTLS +10/-35/+10/-35

With this settings i passed 8hs MEMTEST no errors but i can only pas 15min BLEND...
I changed CPU GTLS but BLEND fails before or after---I also tried to run PL10, LIGHTER, seems the same, it doesn't come from memory as it passed overnight tests...

I don't know maybe is the chip i also tried with 1,42 vtt and no go also, more PLL also fails sooner, the only one is vcore at 1,4 set on bios it idles at 1,39 and loads 1,4.

Thanks
Sergio
01-22-2009, 06:35 AM
kill_a_wat

Quote:

Originally Posted by andressergio

hey mate

I tried this settings and tested carefully

467 x 9 MEMS 1245 5-5-5-15-5-65-8-5

CPU Skews Normal - NB Skew delay 100
RAM SKEWS all channels on 100
NB GTL +40 /DDR REF +12,5 A/B
NB DDR REF -25
MEM OC Charger = disabled
STATIC READ = disabled
PL 7 / STRONGER

vcore set on bios 1,4
pll 1,526
vtt 1,4
nb 1,45
sb 1 1,55
sb 2 1.2

CPU GTLS +10/-35/+10/-35

With this settings i passed 8hs MEMTEST no errors but i can only pas 15min BLEND...
I changed CPU GTLS but BLEND fails before or after---I also tried to run PL10, LIGHTER, seems the same, it doesn't come from memory as it passed overnight tests...

I don't know maybe is the chip i also tried with 1,42 vtt and no go also, more PLL also fails sooner, the only one is vcore at 1,4 set on bios it idles at 1,39 and loads 1,4.

Thanks
Sergio

Hi Sergio

It might be possible that you have hit a limit on your CPU/Mobo...I really can't say for sure...the only way really is to either try some more or try a different setup....:shrug:

It looks like you have done quite a bit of fiddling and still have had no luck.

From your previous post it seems you have already tried to fiddle with your CPU and NB skews....what happens when you raise the vCore? Also what happens if you raise the north bridge volt? In all honesty I haven't noticed any difference with my gaming with a 4.41Ghz and a 4Ghz...I just wanted to get the most out of my CrossFireX and will probably use my 4.23Ghz profile as a nice compromise 24/7.

I did a quick test on 470x9 with lowered vCore (1.36 load 1.35 idle) on my Prime Blend stable 4.2gb profile:

25 run IBT max stress ~3gb memory -

http://img111.imageshack.us/img111/8...0423ghzew1.jpg
01-22-2009, 06:49 AM
andressergio

Quote:

Originally Posted by kill_a_wat

Hi Sergio

It might be possible that you have hit a limit on your CPU/Mobo...I really can't say for sure...the only way really is to either try some more or try a different setup....:shrug:

It looks like you have done quite a bit of fiddling and still have had no luck.

From your previous post it seems you have already tried to fiddle with your CPU and NB skews....what happens when you raise the vCore? Also what happens if you raise the north bridge volt? In all honesty I haven't noticed any difference with my gaming with a 4.41Ghz and a 4Ghz...I just wanted to get the most out of my CrossFireX and will probably use my 4.23Ghz profile as a nice compromise 24/7.

I did a quick test on 470x9 with lowered vCore (1.36 load 1.35 idle) on my Prime Blend stable 4.2gb profile:

25 run IBT max stress ~3gb memory -

http://img111.imageshack.us/img111/8...0423ghzew1.jpg

Thanks mate my chip or mobo or whatever reason needs 1,42 to pass that...

IN your same volts i can do stable 4140 (460x9) 1227 PL7 Stronger

ALSO on my sig speed i discovered that i need 2 notchs of vcore as i tested yesterday and gave me residual norm...so 4185 (465x9) 1240 PL7 Stronger needs 1,39 idle and 1,4 load

funny thing is that at this speed MEMS loves this 1200+ speed and PL7, i tested all overnite on memtest various times and passes perfect, but if i go on other mems settings i dig intro troubles, maybe it comes from that.

Cheers and thank you for your help.
Sergio
01-22-2009, 08:21 PM
EOD

Quote:

Originally Posted by EOD

I just got my Q9650 today from newegg. it is batch: L826A965 with 1.25v vid

4.2GHz (467 FSB * 9 multi) at 1.296v vcore at load (1.312 idle) and Running H2O.

http://valid.canardpc.com/show_oc.php?id=490072

I made sure I was ready for this chip. I spent the last few days tweaking my motherboard and (now old Q6700) for a stable 467 FSB OC. Once I got it dialed in, It was a matter of just stabilizing the vcore. So far I am just past 6Hrs stable in Prime95.

I have been considering going with a UD3P to see what this chip can really do...

One core failed 6.5hrs into the test, so I upped the vcore slightly. Here are the results:

16hrs Prime95 stable

http://i83.photobucket.com/albums/j2...tprimetest.jpg
01-22-2009, 08:34 PM
radaja

EOD,very nice,is this your first quadcore?just curious as to what the learning curve is coming from a dual core.is there much difference OCing a quad?also what warehouse did newegg ship your 9650 from?EDIT-i just saw that you have a q6700 sorry.but maybe you can still give me some advice?
01-22-2009, 08:46 PM
ElAguila

One last question here for my peace of mind. Is it "fairly safe" to run the Q9650 24/7 at 1.35 vcore if the max temps on all four cores never goes above 61C? I was able to get it stable at 4250MHz but I have to increase the vcore to 1.35(bios setting and reading at 1.347).
01-22-2009, 09:29 PM
kill_a_wat

Quote:

Originally Posted by ElAguila

One last question here for my peace of mind. Is it "fairly safe" to run the Q9650 24/7 at 1.35 vcore if the max temps on all four cores never goes above 61C? I was able to get it stable at 4250MHz but I have to increase the vcore to 1.35(bios setting and reading at 1.347).

IMO as long as it is stable then its all good. How long will it last? I have no idea....for me as long as the load temps are <70 i'm happy.

Show 100 post(s) from this thread on one page