not yet...
Printable View
not yet...
:up:Quote:
Originally Posted by Ace-a-Rue
Now I can't wait to get my mobo back :yepp:
Abit 12 bios working quite good with the E8400
Max Bus 560 FSB 2243
http://www.imgx.org/thumbs/small/11661_2l3lr/560.jpg
24/7 500x8 4ghz 1.28v
http://www.imgx.org/thumbs/small/116...4000stable.jpg
what kind of current are you pulling when you run Prime 95 at 4ghz?Quote:
Originally Posted by farookh
its about 48AQuote:
Originally Posted by Ace-a-Rue
WOW...that's all!...impressive, even for a dual core!...so...doubling that would approximate a quad core at 4ghz...hmmmmQuote:
Originally Posted by farookh
what kind of vtt and gtls settings are you using on 500x8? I've got nearly the exact same setup and i can do 485x8 rock solid, but 490x8 is unstable regardless of the cpu voltage (I have tried 1.3 plus). I know i havent hit the fsb wall yet.Quote:
Originally Posted by farookh
using 1.2v cpu
vtt 1.25
gtls 67 etc
What voltage are you giving your mobo? (MHC, ICH, ICHIO)Quote:
Originally Posted by hazardous
It will help if you raise them too, the mobo runs cool anyway :)
1.2v i could boot into vista but not prime stable had to set mine 1.275Quote:
Originally Posted by hazardous
Cpu VID 1.275
MCH 1.45
CPU VTT 1.27
ICH 1.11
rest all default.
Finally got my stable at 500x8. 1.25volts, vtt 1.25, increased MCH and ICH by .05 volts from stock. Though, strangely i got 1k less in 3dmark 06 than i did at 450x9. Go figure.Quote:
Originally Posted by farookh
when i run 9x450 the amp reading on guruQuote:
Originally Posted by AMDfreak
idle 46
load 109 (all 4 core working)
vcore 1,7
cpu vtt 1,76
cpu pll 1,7
stability depend on temp,thats the highest i can get on air :)
Is there anyone using MCW30 to cool northbrigde of this board?
Should I go for RMA or wait for BIOS 13?Quote:
Originally Posted by Beastage
It happened several more times, but then I tried saving to bios after changing every little option and rebooting and it holds since.
http://www.koolance.com/water-coolin...product_id=437Quote:
Originally Posted by Boyu
maybe this one would fit on the board.....
Is this board better then a Asus Maximus Formula?
This is what my E8400 is doing on this board with latest official release bios
E8400 + Abit IX38 @ 572 FSB :D
Quote:
Originally Posted by Darklord
how are you cooling that 8400?...LN2, DICE?
Following the link it says DICE ;)
I had the same problem once when using another board. It was caused by insufficient voltage supplied to one of the components in the motherboard.Quote:
Originally Posted by Beastage
My problem before was solved by raising Vcore one step.
May be you should consider raising your voltage too, one or two steps m8, and pray that it helps. :yepp:
I think that might fight the SB, but I dont see it fitting the NB. I've done alot of searching and cant find anything to cool my NB. Maybe if the board grows in popularity some company will release blocks specifically for the board like they did for asus boards.Quote:
Originally Posted by Chiboy04
This might help you ;)Quote:
Originally Posted by hazardous
Really want a new bios to :)
right...i did but stopped reading:DQuote:
Originally Posted by jcool
Its done with DICE. Trying for more. Too bad this board doesnt support Memset,it becomes a pain when you want to bench at high clocks.
Atleast Abit should include memory timings thing in uGuru :(
any body like to forward this to abit :D it would be nice to have :yepp:Quote:
Originally Posted by Darklord