Geez ... I haven't even tried 0702 ... :(
Printable View
Geez ... I haven't even tried 0702 ... :(
The supplied active NB heat sync is too big to go with my Utra 120 CPU sync. Anyone else doing a guetto cooling system with a 40mm fan?
Right now I'm about 60 degrees at idle, wouldn't mind getting it down a few more degrees.
im in the high 30's to 40s on my torture rack jeff for reference. Fans all over though def help
Yah, I'd pound it with air and keep it open if I didn't need major silence when mixing down audio.Quote:
Originally Posted by Splave
http://www.scythe-usa.com/product/ac...0l_detail.html
This little guy doesn't move allot of air, so I'm thinking it's going to have to be right down flush with the passive sync, offset a bit to avoid the dead spot. Would pull be better in this situation to not push the heat back down on itself?
jeff the Enzotech SLF-1 did a good job on my rexIIQuote:
Originally Posted by Jeff Flowerday
but i suggest the Enzotech CNB-S1 the rexIII runs a bit hotter
cooler nb = cooler sb and pwm;)
i'm on water and i dont hit 40c
anyone running this new bios yet? i skipped 0702 :ROTF:
is 0704 public release or a beta again?
i like the sound of those extra settings might help with my rig :)
Do you have a link where we can find it? I have 0602 and its running fine at 4.3 Ghz
bios 704
seems to read the correct volts for cpu in everest ultimate more accurately
when i installed windows re-recognized my cpu, (new microcode?)
seems better than 702....smoother
here u go;Quote:
Originally Posted by KaRLiToS
http://www.mediafire.com/?g3ncuiagknz
I just flash from 602 to 704 and My crossfire Setup is now working, I didnt have to make any voltage modification or anything except for vcore. I didnt even touch the IOH voltage (1.19v for crossfire)
Thanx for your help everyone...
Newb question ... IOH refers to In Out Hub or the SouthBridge? And ICH refers to Integrated Controller Hub or Northbridge? What controls the PCI-E voltage? In BIOS there are IOH PCI-Ev and ICH PCI-Ev ... which one does what?
PS: Also flashed to 0704 ... ASUS EZ-Flash 2 is the best :up:
Yet another crap retail i7 980x!!! :(
seriously... :)
http://i43.photobucket.com/albums/e3...olet/cpu-z.png
Just wondering if anyone has a W3570 in there R3E. My w3570 is is a gem batch and it does 4.2 easy as but when i try for 4.4 linx fails going into 2ndpass
I have tried all i can think of but cannot for the life of me get it stable.
My cpu does 4.8 on casecade with 1.3 volts i thought for sure it would do 4.4 on water.
I have even up the cpu volts to 1.4 and nothing
Have aloso tried different multi's
Have even tried 20x210 for 4.2 it wont even do that
I just got the R3E today to replace Gigabyte EX58-EXTREME and I have a big problem with my RAM
It is OCZ Blade DDR3 2000 CL9 (9-9-9-30-2N)
The exact RAM worked fine with the Gigabyte Extreme Mobo but it gives no POST with the R3E , the strangest thing is that it did the same thing with a friend's Asus P6T Vanilla mobo
I can't get the RAM to POST @ 2000 CL9 but it workd fine @ 1600 CL7
With the Gigabyte Mobo I OCed my Core i7 920 to 4.22Ghz and RAM @ 2010 9-9-9-28-1N
Voltages for Gigabyte were :
CPU @ 1.275v
VTT @ 1.555v ( Yes it is high but the Blade RAM would only work at this high VTT Voltage)
DRAM @ 1.66v
With the same settings and voltages, the R3E would not POST with 2000Mhz DDR3 :confused:
So , I have 2 different Asus mobos that refuse to POST with the same Memory while Gigabyte worked just fine
What can I do ?
I've tried different BIOS settings/ Voltages with the same No POST problem
I've even tried BIOS 0704
Quote:
Originally Posted by Ka0sX
These are mine .. if any good to you
Quote:
Originally Posted by needforspeed
thanks mate any chance you could do a bios template for me ? Would much appreciate it.
Also what bios are you using.
Thanks
These are no my setting but just a template i grab would you mind editing with what your current bios settings are
Quote:
Code:
Target CPU Frequency 4410MHz
Target DRAM Frequency 1683MHz
LN2 Mode: Disabled***
QPI Loadline Calibration: Enabled***
Sync Mode [Enabled]
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [21.0]
CPU Turbo Power Limit [Disabled]
>CPU Configuration----------------------------
CPU Ratio Setting [21.0]
C1E Support [Enabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetcher [Enabled]
Intel(R) Virtualiyation Tech [Enabled]
CPU TM Function [Disabled]
Execute Disable Bit [Enabled]
Intel(R) HT Technology [Enabled]
Active Processor Cores [All]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Enabled]
Intel(R) C-STATE Tech [Enabled]
C State package limit setting [Auto]
----------------------------------------------
BCLK Frequency [210]
PCIE Frequency [100]
DRAM Frequency [1683]
UCLK Frequency [3789]
QPI Link Data Rate [7579]
Memory Configuration Protect [Disabled]
>DRAM Timing Control--------------------------
CAS# Latency 6 [6]
RAS# to CAS# Delay 7 [7]
RAS# PRE Time 6 [6]
RAS# ACT Time 18 [18]
RAS# to RAS# Delay 4 [4]
REF Cycle Time 72 [72]
WRITE Recovery Time 12 [10]
READ to PRE Time 6 [6]
FOUR ACT WIN Time 24 [Auto]
Back-To-BackCAS# Delay 0 [Auto]
Timing Mode 1N [1N]
Round Trip Latency on CHA 60 [60]
Round Trip Latency on CHB 62 [62]
Round Trip Latency on CHC 64 [64]
WRITE To READ Delay(DD) 8 [Auto]
WRITE To READ Delay(DR) 8 [Auto]
WRITE To READ Delay(SR) 18 [Auto]
READ To WRITE Delay(DD) 7 [Auto]
READ To WRITE Delay(DR) 7 [Auto]
READ To WRITE Delay(SR) 7 [Auto]
READ To READ Delay(DD) 7 [Auto]
READ To READ Delay(DR) 6 [Auto]
READ To READ Delay(SR) 4 [Auto]
WRITE To WRITE Delay(DD) 8 [Auto]
WRITE To WRITE Delay(DR) 8 [Auto]
WRITE To WRITE Delay(SR) 18 [Auto]
----------------------------------------------
CPU Differential Amplitude [Auto]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-Balanced]
PWR Volt. Control [Auto]
Load-Line Calibration [Full]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [1000kHz]
Extreme OV [Disabled]
Extreme OC [Auto]
CPU Voltage 1.415 [1.41250]
CPU PLL Voltage 1.812 [Auto]
QPI/DRAM Core Voltage 1.310 [1.31250]
DRAM Bus Voltage 1.654 [Auto]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM DATA REF Voltage on CHB [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHC [Auto]
DRAM CTRL REF Voltage on CHC [Auto]
----------------------------------------------
IOH Voltage 1.244 [Auto]
IOH PCIE Voltage 1.508 [Auto]
ICH Voltage 1.111 [Auto]
ICH PCIE Voltage [Auto]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
***on-board jumper dependant
xxxxxxxx
OK these are mine .. I am actually using 0531 Bios.. I did not get on with 601/602.. Havnt tried 704 yet.
Sync Mode [Disabled]
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [29.0]
CPU Turbo Power Limit [Disabled]
>CPU Configuration----------------------------
CPU Ratio Setting [29.0]
C1E Support [Enabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetcher [Enabled]
Intel(R) Virtualiyation Tech [Disabled]
CPU TM Function [Disabled]
Execute Disable Bit [Enabled]
Intel(R) HT Technology [Disabled]
Active Processor Cores [All]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Enabled]
Intel(R) C-STATE Tech [Enabled]
C State package limit setting [Auto]
----------------------------------------------
BCLK Frequency [156]
PCIE Frequency [103]
DRAM Frequency [1870]
UCLK Frequency [3789]
QPI Link Data Rate [7579]
Memory Configuration Protect [Disabled]
>DRAM Timing Control--------------------------
CAS# Latency 6 [7]
RAS# to CAS# Delay 7 [7]
RAS# PRE Time 6 [7
RAS# ACT Time 18 [20]
RAS# to RAS# Delay 4 [auto]
REF Cycle Time 72 [auto]
WRITE Recovery Time 12 [auto]
READ to PRE Time 6 [auto]
FOUR ACT WIN Time 24 [Auto]
Back-To-BackCAS# Delay 0 [Auto]
Timing Mode 1N [1N]
Round Trip Latency on CHA 60 [auto]
Round Trip Latency on CHB 62 [auto]
Round Trip Latency on CHC 64 [auto]
WRITE To READ Delay(DD) 8 [Auto]
WRITE To READ Delay(DR) 8 [Auto]
WRITE To READ Delay(SR) 18 [Auto]
READ To WRITE Delay(DD) 7 [Auto]
READ To WRITE Delay(DR) 7 [Auto]
READ To WRITE Delay(SR) 7 [Auto]
READ To READ Delay(DD) 7 [Auto]
READ To READ Delay(DR) 6 [Auto]
READ To READ Delay(SR) 4 [Auto]
WRITE To WRITE Delay(DD) 8 [Auto]
WRITE To WRITE Delay(DR) 8 [Auto]
WRITE To WRITE Delay(SR) 18 [Auto]
----------------------------------------------
CPU Differential Amplitude [900]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-Balanced]
PWR Volt. Control [Auto]
Load-Line Calibration [Full]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [1000kHz]
Extreme OV [Disabled]
Extreme OC [Auto]
CPU Voltage 1.415 [1.368]
CPU PLL Voltage 1.812 1.812
QPI/DRAM Core Voltage 1.310 [1.337]
DRAM Bus Voltage 1.654 [Auto]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM DATA REF Voltage on CHB [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHC [Auto]
DRAM CTRL REF Voltage on CHC [Auto]
----------------------------------------------
IOH Voltage 1.244 [Auto]
IOH PCIE Voltage 1.508 [Auto]
ICH Voltage 1.111 [Auto]
ICH PCIE Voltage [Auto]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
Thanks for the settings, i have been waiting to fire up my
w3570 and r3e but now i think i will do it this weekend and use your
settings as a starting point...
thanks :up:
Quote:
Originally Posted by needforspeed
Thanks needforspeed
Will try that later when i put mt rig back together.
Cpu volts seem high for 24/7 what are max temps we can go on these chips for 24/7?
EDIT
Load-Line Calibration [Full]
CPU Voltage 1.415 [1.368]
You LLC is on FULL doesnt that increase voltage when underload?
Your CPUV is set to 1.425 in Bios and underload it does to 1.368?
When i had my llc on FULL it was increasing Volts under load
Quote:
Originally Posted by Ka0sX
Sorry No ...my settings are in the brackets... I have cpu set at 1.368 in bios and with LLC the CPU V is same in windows (everest 5.5 reads cpu v, very well but CPU-Z is screwed up...)
Unless I read bingo's post incorrectly third party CPUv should be fixed shortly. :woot:
Anyone having issues with the board not posting when you make a change in the BIOS?
Every time I change anything, it fails to post. Even if everything is stock and it has nothing to do with overclocking...
reseat the cpuQuote:
Originally Posted by bassplayer
i'm guessin i didnt post warning big enough:rofl:
Put it in your sig, lol... or ask the OP to post the warning in post #1 in BIG RED LETTERSQuote:
Originally Posted by zsamz_
Is this after you flashed to new BIOS or just any change to BIOS settings? Seems strange, but I always set to default settings (F5) before flashing BIOS. I use ASUS EZ-Flash 2. That is the best way to flash BIOS IMO.Quote:
Originally Posted by bassplayer
Strange thing happened today though. I have my two HD4870x2's in X-fire and when I went to new Catalyst drivers 10.5, I had strange artifacting and then reboot. I did not change voltage in PCI-E after flashing to new 0704 BIOS. I had to remove one video card and remove drivers via hardware device. I then was able to reload new 10.5 drivers and everything is okay. But question is which PCI-E voltage do I change? Southbridge or Northbridge?