So you wanted the ultimate Vdimm control...here it is!!!

Printable View

Show 100 post(s) from this thread on one page

04-12-2006, 09:59 AM
NapalmV5

Quote:

Originally Posted by ugp

WHATS NEXT?

Getting a motherboard that supports 8 Video cards, 4 Quad Core CPUs, and 20GB of RAM! Overclock all of that!

Give it time...I am sure it is down the road somewhere lol...I am just dreaming...

LOL.. thousands of settings in total, guess only the xtreme will be able to keep up...
04-12-2006, 10:16 AM
MikeMK

Well i preordered mine earlier in the week, and it came instock today. Its been shipped out to me so i should have it tomorrow!!! :D
04-12-2006, 10:51 AM
fareastgq

well, guess I'll be picking up a few of these. (was just gonna pick up 1 before, heh)
04-12-2006, 11:09 AM
Aerou

any news when will it be released? anything more specific .... I just can't wait, I'm gonna pop :brick:
04-12-2006, 01:32 PM
MikeMK

Its in stock at a couple of places already here in the UK, so its released already i guess!
04-12-2006, 03:11 PM
AndreYang

Quote:

Originally Posted by Tony

Andre

I have 0307 off Oskar, do you have later?

Its actually dated 04/06/2006

It's the same Bios.:)
04-12-2006, 03:16 PM
Tony

Quote:

Originally Posted by AndreYang

It's the same Bios.:)

I just releae a tweaked version in the bios forum.
04-12-2006, 03:30 PM
Blacklash

Since my 4400 can't do more than 2.76 Ghz anyway I just ordered the Abit AT8 32X. It's got passive cooling and plenty of vcore and vdimm. I use the G skill in my sig so I don't need a lot of vdimm in the first place.

I'll be able to use my PCI-e tuner card in the top slot and a sound card in the bottom. It will be tight and I know some folks that have made 'em fit.

I am sure the DFI will be a better board for extreme overclocking and the AT8 32X should suit my "mid high" needs. I need to reinstall windows very soon, and I was tired of the "next week" thing that has been going on for some time, so I went with this option. Not to mention the Abit RD580 board is only about five dollars or so more than the old DFI RD 480 board.
04-13-2006, 01:27 AM
andyr(uk)

Quote:

Originally Posted by Tony

Came from Oskar like that, only issue was the bios was so tight it hated anything Infineon...no worries though ;) i have a modded version off to DFI USA and they are testing to see if they can release it. If they give the go ahead I will leak it here ready for your new boards. The stock bios on the boards is not to hot and should be flashed ASAP.

Hi Tony , Infineon ran well with the standard bios then , only i have some Mushkin 2GB DDR XP4000 Redline Extreme, default timings are 3-3-2-8 , is that the sort you tried
04-13-2006, 02:39 AM
El Snorro

Nice!

I'm gonna buy this mobo as soon as its available in the Netherlands!:toast: :banana:
04-13-2006, 02:56 AM
jrw

Is it tehcnically possible to allow manipulation of ALL those Drive Strenghts in Windows via the A64 Tweaker?

Would make it a lot easier to "play" with them :)
04-13-2006, 03:07 AM
Tony

Quote:

Originally Posted by jrw

Is it tehcnically possible to allow manipulation of ALL those Drive Strenghts in Windows via the A64 Tweaker?

Would make it a lot easier to "play" with them :)

No it is not
04-13-2006, 03:08 AM
Tony

Quote:

Originally Posted by andyr(uk)

Hi Tony , Infineon ran well with the standard bios then , only i have some Mushkin 2GB DDR XP4000 Redline Extreme, default timings are 3-3-2-8 , is that the sort you tried

No i had to flash to the bios I posted, make sure if you are using Infineon you boot with 1 dimm and flash the bios, once setup defaults are loaded all is good.

Remember also i set 2t by default in the bios so you will need to put this back at auto or enabled.

Show 100 post(s) from this thread on one page