hey yall!
been a while since i posted here, and im totally out of the loop on whats new with the Maximus formula --> maximus rampage conversion.
i looked around the asus website, and noticed the "Rampage Formula 0601 Bios"
im on 308!
what do yall think ? update to the 601 ?
0601 = Downgrade.Quote:
Originally Posted by ericab
MF Newest ist 1207
RF Newest is 0410
Have fun ;)
If anyone can respond to my problem it'd be appreciated.
EDIT: My bad, where'd you find a 06 bios for rampage o.o
I finally got 3.82ghz stable out of my q9550 and rampage formula. 4.0ghz, here I come....
http://i69.photobucket.com/albums/i7...38STABLE-1.jpg
I should note that I did pass the 2 hour test, I only started doing the 20 minute tests because I was individually lowering my volts down 1 by 1 so just needed a quick stability test to make sure it stayed stable.
very good, glad you got it sorted out. :up:Quote:
Originally Posted by Michowski
Has anyone tested the new bios for Rampage??
11/04/2008 12:22AM 1,000,003 RAMPAGE-ASUS-Formula-0601.zip
Was wondering if it offered anything
Well all night ive been struggling to get to 3.9 but I just cant get it stable. Been reading around and came to the conclusion that my 9550 limit is 448 fsb x 8.5 multi. Im stable all day at 448 but once I started bumping it higher, I cant last more then 1 minute on occt wether its mix, ram, or cpu. Doesnt matter. I updated my latest test in post 7278. Thats were I want to keep it for 24/7 use. Are all my volts in good shape for that? Any reason not to?
It is difficult to help you out when your parts aren't listed. What ram are you using. If your ram can run stable @ 1132 then here is:Quote:
Originally Posted by Michowski
Easy 4Ghz on Rampage Formula (8.5x471)
Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 8.5
FSB Frequency : 471
FSB Strap to North Bridge : 333
PCI-E Frequency: 110
DRAM Frequency: DDR2-1132
CLOCK SKEW Normal both channels
DRAM Command Rate : 2T
DRAM Timing Control: AUTO
DRAM Static Read Control: Disabled
Ai Clock Twister : AUTO
Transaction Booster : Manual
Common Performance Level [7] Try 8 if you fail at 7
Pull-In of CHA PH1 Disabled
Pull-In of CHA PH2 Disabled
Pull-In of CHA PH3 Disabled
Pull-In of CHA PH4 Disabled
Pull-In of CHA PH5 Disabled
Pull-In of CHB PH1 Disabled
Pull-In of CHB PH2 Disabled
Pull-In of CHB PH3 Disabled
Pull-In of CHB PH4 Disabled
Pull-In of CHB PH5 Disabled
CPU Voltage : 1.375 (1.360 actual) You may need more
CPU PLL Voltage : 1.50 Leave this pegged at this setting, it makes my system very unstable with any 45nm cpu
North Bridge Voltage : 1.57 (actual)
DRAM Voltage : ???
FSB Termination Voltage : 1.40v (1.30v actual)
South Bridge Voltage : 1.125
SB 1.5V Voltage : 1.60v
Loadline Calibration : Enabled
CPU GTL Reference : 0.67X
North Bridge GTL Reference : 0.67X
DDR2 Channel A REF Voltage : DDR2-REFF
DDR2 Channel B REF Voltage : DDR2-REFF
DDR2 Controller REF Voltage : DDR2-REFF
@Grnfinger; What's the latest on your RF, did you get to play with it yet?
Well the VID is 1.25v.Quote:
Originally Posted by Grnfinger
I have to get the box out of the closet and get you the batch number.
Store where I bought was out of stock, they now have them in but I cant decide what to get, Rampage or a Giga UD3.Quote:
Originally Posted by Zucker2k
This will be my last board b4 i7 so I am torn.
Rampage Bios 601 is a nice bios, Very stable and I could drop 1 notch of vCore and vtt :up:
Rig is on air so any little bit helps
memory- OCZ2P10664GKQuote:
Originally Posted by Zucker2k
cpu- q9550
mainboard- asus rampage formula x48
OS- Vista ultimate 64
video- radeon 4870
I have tried for 3.9 and I could not get it stable. I even turned everything but vcore on auto and it still wasnt stable. I crossed that 450 barrier and no matter what I couldnt get it stable. I had 1:1 ratio for fsb/ram. I feel like im just capped at 3.82ghz.
running on auto is not a good idea, unless you want to buy new hardware in a month or 2.Quote:
Originally Posted by Michowski
To determin if its a FSB wall lower your multi 475x8 , 475x7
1.35vcore for 3.8GHZ should leave alittle room for 3.9 -4.0 but if your chip scales poorly then you might need 1.425 for 3.9GHz, 1.475 for 4.0GHz
I only went to auto to see if I could get my system stable past 3.82 and I still couldnt.
Before my CPU PLL Voltage was at 1.60 and my NBv had to be set at 1.65 for it to be stable, now when I lowered the CPU PLL Voltage to 1.50, my NBv is at 1.53. So it really does make a difference in terms of stability. :)Quote:
Originally Posted by Zucker2k
I have a general question about when you flash a new bios to MF/MR boards. That question is when you flash a bios and the application says that it is erasing/writing the bios from/to the ROM, does any one else get two blocks towards the end of the progress bar that seem to be skipped? What i mean by this is they are still yellow, however are half pixel shaded in appearance. The flashing app will say it has completed successfully how it just bothers me....
Did you advance clock skews? what temps are you getting for cpu and NB?Quote:
Originally Posted by Michowski
No, my memory is all on auto except for the voltage. Temps for cpu are 40 idle, low 50's gaming. NB is 50 idle.
hmm what's temp at load; that nb voltage seems a little on the high side. Set DRAM control to 'manual' and advance clock skews to 300 each on A/B; that should do the trick.
590 FSB 1:1
maximus formula thermalright NB+SB modded
NB 1.87v
FSB VTT 1.94V
http://valid.x86-secret.com/show_oc.php?id=434231
That;s got to be the highest vtt yet; you don't need that much vtt for 590. I did 600fsb (7.5x600) with 1.34vtt on RF.Quote:
Originally Posted by westsider
http://www.xtremesystems.org/forums/...95&postcount=1
it couldnt boot otherwise
and i had to give SB 1.2v and 1.55@1.65
so has HDD controller functioned
otherwise:
"not proper boot device" :)
Under occt it gets to 70c for cpu and upper 50's for nb. While gaming tho those both never get close to those temps. I was gaming a good 8 hours yesterday and she was flawless. Nothing got above 55c from video card to mb and everything inbetween.Quote:
Originally Posted by Zucker2k
OK I have a problem...I can prime for 8 hrs straight without any problems, but if I prime while playing a video for like 10-15 mins the whole system freezes. Any ideas? I tried upping my NBv to 1.65 and it still freezes after 10-15 mins while priming and playing a video. Heres my BIOS settings:
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 8.5
FSB Frequency : 471
FSB Strap to North Bridge : 333
PCI-E Frequency: 110
DRAM Frequency: DDR2-1132
CLOCK SKEW Normal both channels
DRAM Command Rate : 2T
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : 3
Row Refresh Cycle Time : 55
Write Recovery Time : 6
Read to Precharge Time : 3
Read to Write Delay (S/D) : 8
Write to Read Delay (S) : 3
Write to Read Delay (D) : 5
Read to Read Delay (S) : 4
Read to Read Delay (D) : 6
Write to Write Delay (S) : 4
Write to Write Delay (D) : 6
Write to PRE Delay : 14
Read to PRE Delay : 5
PRE to PRE Delay : 1
ALL PRE to ACT Delay : 5
ALL PRE to REF Delay : 5
DRAM Static Read Control: Enabled
Ai Clock Twister : Stronger
Transaction Booster : Manual
Common Performance Level [7]
Pull-In of CHA PH1 Disabled
Pull-In of CHA PH2 Disabled
Pull-In of CHA PH3 Disabled
Pull-In of CHA PH4 Disabled
Pull-In of CHA PH5 Disabled
Pull-In of CHB PH1 Disabled
Pull-In of CHB PH2 Disabled
Pull-In of CHB PH3 Disabled
Pull-In of CHB PH4 Disabled
Pull-In of CHB PH5 Disabled
CPU Voltage : 1.33725 (1.32 actual)
CPU PLL Voltage : 1.50
North Bridge Voltage : 1.53
DRAM Voltage : 2.12
FSB Termination Voltage : 1.4
South Bridge Voltage : 1.050
Loadline Calibration : Enabled
CPU GTL Reference : 0.67X
North Bridge GTL Reference : 0.67X
DDR2 Channel A REF Voltage : DDR2-REFF
DDR2 Channel B REF Voltage : DDR2-REFF
DDR2 Controller REF Voltage : DDR2-REFF
SB 1.5V Voltage : 1.5
I just put them both on 300, so I should try for 4.0ghz again?Quote:
Originally Posted by Zucker2k
Futastic.
1) Graphic card still OK?
2) DRAM Speed over stock
3) Maybe try to run a video with an upped vCore
The graphics card is fine. I tried running DRAM at 1:1 at 943MHz and it still does the same thing. So you think I should bump the CPU vCore up even tho its stable while priming for 8+ hours?Quote:
Originally Posted by Allubz