Asus A8N32-SLI initial impression....WOW!

Printable View

Show 100 post(s) from this thread on one page

12-12-2005, 03:58 PM
MFM

Can anyone please tell me if this mobo had already kill some cpu @ default settings (Without any kind of OC) ????

My DFI Expert kill my FX-55, 2GB Patriot mems, and of course the mobo itself, and i'm thinking to buy this one until DFI resolve my prob.

Regards,
12-12-2005, 04:07 PM
AppaYipYip

Quote:

Originally Posted by MFM

Can anyone please tell me if this mobo had already kill some cpu @ default settings (Without any kind of OC) ????

My DFI Expert kill my FX-55, 2GB Patriot mems, and of course the mobo itself, and i'm thinking to buy this one until DFI resolve my prob.

Regards,

I'm sorry to hear that! :(

I have not heard of a single reported "CPU kill" from the Asus A8N32, and I am a member of 4 computer hardware forums and involved in 2 seperate thread discussions about this motherboard (here and [H]ardForums).

So I think it's a safe bet! :D
12-12-2005, 04:28 PM
mdzcpa

Quote:

Originally Posted by MFM

Can anyone please tell me if this mobo had already kill some cpu

Like this?
http://www.xtremesystems.org/forums/...&postcount=655

Read this thread. Its reported on page 27.
12-12-2005, 04:30 PM
Zeus...

Quote:

Originally Posted by AppaYipYip

My CPU temps on my Opteron are around 40*C idle, up to 47*C under full load for hours. These temps are higher than on my previous Asus A8N SLi Premium using the same Zalman cooler.

Different mobo so hard to compare real temps as it depends how the bios is converting the reading on the diode and converting them to temps (new bios temps change with the new bios as changes r made but temps may be the same ) also the Vcore may be different too reguardless what and software is saying.

Unless u use a temp probe (which also has its margins off error) on the CPU on the differnt mobos comparing is relative - well it is IMHO
12-12-2005, 04:33 PM
AppaYipYip

Quote:

Originally Posted by Zeus...

Different mobo so hard to compare real temps as it depends how the bios is converting the reading on the diode and converting them to temps (new bios temps change with the new bios as changes r made but temps may be the same ) also the Vcore may be different too reguardless what and software is saying.

Unless u use a temp probe (which also has its margins off error) on the CPU on the differnt mobos comparing is relative - well it is IMHO

Ohh I see, thank you for the explaination. So do you think those temps are kind of high for an Opty 175 clocked @ 2.5 GHz with 1.375 vCore?
12-12-2005, 04:45 PM
Zeus...

Quote:

Originally Posted by AppaYipYip

Ohh I see, thank you for the explaination. So do you think those temps are kind of high for an Opty 175 clocked @ 2.5 GHz with 1.375 vCore?

Well thats only my opinion -

but u have a better HSF than the STD one and with only 1.375 Volts it should be fine - running mine at 1.5Vore and b4 I got the water cooling it was at 50-55C under load so your should be fine - infact its only warm :D
12-12-2005, 04:50 PM
MFM

Ohh my GOD..... :eek: :shock:

Today we can't buy a mobo that doesn't kill cpu's???? :confused:
12-12-2005, 06:28 PM
smurfmods

ASUS Engineering team

I sent the following to the ASUS Engineering team. Lets see what kind of response we get back. I have there email address if anyone wants to PM me. (only for serious issues and broken features, they don't want run of the mill "where does the floppy drive plug into" type stuff)

*****I have the AN832-SLI version 901 bios. What has changed or been fixed in this version bios? Is this still beta?

Has the voltage reporting been fixed? No matter what you set the voltage to over 1.4 volts it doesn't go up. ~1.4v is basically the max unless you use the overvoltage feature (+0.200 mv) then it does work. You can verify this with a multimeter on the board itself.

Thank you very much. The community loves this board!!! Check this website out... (it also list some of the issues guys are having with it if your interested.)

http://www.xtremesystems.org/forums/...ad.php?t=80491

Thanks for making such an awesome motherboard. There are some bugs to work out but I know you guys can fix em.*****
12-12-2005, 06:48 PM
specofdust

Let's hope they get a rep on here to help the people who've got one of these things through initial(and sometimes serious) problems.
12-12-2005, 06:51 PM
cronic

Quote:

Originally Posted by smurfmods

I sent the following to the ASUS Engineering team. Lets see what kind of response we get back. I have there email address if anyone wants to PM me. (only for serious issues and broken features, they don't want run of the mill "where does the floppy drive plug into" type stuff)

*****I have the AN832-SLI version 901 bios. What has changed or been fixed in this version bios? Is this still beta?

Has the voltage reporting been fixed? No matter what you set the voltage to over 1.4 volts it doesn't go up. ~1.4v is basically the max unless you use the overvoltage feature (+0.200 mv) then it does work. You can verify this with a multimeter on the board itself.

Thank you very much. The community loves this board!!! Check this website out... (it also list some of the issues guys are having with it if your interested.)

http://www.xtremesystems.org/forums/...ad.php?t=80491

Thanks for making such an awesome motherboard. There are some bugs to work out but I know you guys can fix em.*****

why don't you just try it. well i will i will report back shrtly.
12-12-2005, 06:52 PM
pcdoc1

Quote:

Originally Posted by MFM

Can anyone please tell me if this mobo had already kill some cpu @ default settings (Without any kind of OC) ????

My DFI Expert kill my FX-55, 2GB Patriot mems, and of course the mobo itself, and i'm thinking to buy this one until DFI resolve my prob.

Regards,

You can't be serious..........
12-12-2005, 07:06 PM
cronic

well i just flashed to 901 and the memory still reports .5v higher with ai booster and the cpu voltage reports .035v higher. i don't know wher to check the vcore wih a dmm so i can't test, but the vcore and vdimm report the same as 703. the hypertransportt is now a multiplier which is nice. as for overclocking i won't be able to do any testing until my g skill gets here tommorow.
12-12-2005, 07:39 PM
jasonh1234

Quote:

Originally Posted by MrBean

@ Jasonh1234: Make sure you have latest FEAR patch...

...This temp is fine as read within BIOS, when your system is in Bios, cpu is loaded around 90%. YOu will see this drop by a good 5-8 deg C when in OS. Nothing wrong with 45-50 Deg C temp on that cpu.

Thanks for the info. I feel much better now. Well after dinner I'm gonna try that. Load up some other games see if I have any similiar problems.

I'm just glad it's not the spacing on the motherboard causing my GPUs to overheat. The soundcard is pretty snug in there.
I forget if I mentioned this but I also have a 120mm fan blowing down on
the expansion slots.
12-12-2005, 08:05 PM
NISCO PT

Quote:

Originally Posted by MFM

Can anyone please tell me if this mobo had already kill some cpu @ default settings (Without any kind of OC) ????

My DFI Expert kill my FX-55, 2GB Patriot mems, and of course the mobo itself, and i'm thinking to buy this one until DFI resolve my prob.

Regards,

compra carago!!:stick:
i think there are dead cpus but not dead like in your DFI mobo( foi por conice)lol
cumps falorca man:toast:
12-12-2005, 08:55 PM
mhorgel

Hello all.

I am new to this board, and I have read much of this thread, but not all of it. I have enjoyed computers for many years (I can still remember my Commodore-64), but I have just built my first PC completely from scratch with the A8N32-Sli Deluxe. I have an AMD Athlon 64 X2 4400+, 2 GB of Corsair 3500LL Pro, an ATI All In Wonder X1800XL, Creative X-Fi Xtreme Music, and a bunch of Seagate 250 GB SATA-2 Hard Drives and 2 NEC DVD burners.

I have been doing a lot of reading on overclocking, but I am still somewhat unsure of how to proceed. I got my system up to 2.62 GHz (238 MHz X 11), but it was extremely unstable, and started to ignore my PS-2 Keyboard.

Right now (after clearing CMOS), my keyboard is functional, and I am running SuperPi without any errors at BIOS defaults. My approach the other day (that resulted in an unstable system) was to lower the memory clock to 100 MHz, and gradually increase the CPU clock. Once I got it to 238, I increased the memory clock to 183 MHz, as prior experience told me that the system would not boot with a CPU clock of 238 MHz and memory clock of 200 MHz. This is when I ran into trouble.

I realize that the MB is new, and experience is limited, but can anyone out there suggest some settings for this CPU/MB/memory combo that have been successful?

Thanks a lot, any help will be greatly appreciated.

Mark
12-12-2005, 09:25 PM
smurfmods

Quote:

Originally Posted by cronic

why don't you just try it. well i will i will report back shrtly.

I'm on a mach II phase change.. Kinda don't want to mess things up until I know what's different.
12-12-2005, 10:57 PM
Marios

Quote:

Originally Posted by sirkuz

hmmm your superpi 32M seems quite slow for those speeds doesn't it?

Oh I wasn't trying to get a good score here.
I was just checking stability.
So I had all sorts of background programs runing like Avast anti-virus ...
I turned on the screen saver and then I entered the Internet to write some posts...
Though it shouldn't make a big difference on a dual core CPU...

Quote:

Originally Posted by Zeus...

I am getting 31.781 secs at 2700MHz with htt 270 and mem at 180Mhz (133MHz limit in bios) so whats your limit at 'Marios'?

Yours isn't 1Mb? Mine is 32Mb.
12-13-2005, 01:36 AM
PuNiShEr

Quote:

Originally Posted by cronic

well i just flashed to 901 and the memory still reports .5v higher with ai booster and the cpu voltage reports .035v higher. i don't know wher to check the vcore wih a dmm so i can't test, but the vcore and vdimm report the same as 703. the hypertransportt is now a multiplier which is nice. as for overclocking i won't be able to do any testing until my g skill gets here tommorow.

Where can i find this new Bios for download?
I've been to ASUS website and to ASUS FTP, and i can't find that bios :(
12-13-2005, 02:29 AM
gandalf027

Anyone using this board with a lian-li 1000 or 1200?
I'm thinking of buying one, but since is atx inverted i would like to know if the heatpipe solution will work ok.

TIA
12-13-2005, 05:33 AM
Ic3man

Quote:

Originally Posted by gandalf027

Anyone using this board with a lian-li 1000 or 1200?
I'm thinking of buying one, but since is atx inverted i would like to know if the heatpipe solution will work ok.

TIA

From what I've read the heatpipe wont work as well if it is inverted so overclocking will be restricted unless you remove the heatpipe and use individual chipset fans/heatsink.
12-13-2005, 05:45 AM
Ic3man

Quote:

Originally Posted by mhorgel

Hello all.

I am new to this board, and I have read much of this thread, but not all of it. I have enjoyed computers for many years (I can still remember my Commodore-64), but I have just built my first PC completely from scratch with the A8N32-Sli Deluxe. I have an AMD Athlon 64 X2 4400+, 2 GB of Corsair 3500LL Pro, an ATI All In Wonder X1800XL, Creative X-Fi Xtreme Music, and a bunch of Seagate 250 GB SATA-2 Hard Drives and 2 NEC DVD burners.

I have been doing a lot of reading on overclocking, but I am still somewhat unsure of how to proceed. I got my system up to 2.62 GHz (238 MHz X 11), but it was extremely unstable, and started to ignore my PS-2 Keyboard.

Right now (after clearing CMOS), my keyboard is functional, and I am running SuperPi without any errors at BIOS defaults. My approach the other day (that resulted in an unstable system) was to lower the memory clock to 100 MHz, and gradually increase the CPU clock. Once I got it to 238, I increased the memory clock to 183 MHz, as prior experience told me that the system would not boot with a CPU clock of 238 MHz and memory clock of 200 MHz. This is when I ran into trouble.

I realize that the MB is new, and experience is limited, but can anyone out there suggest some settings for this CPU/MB/memory combo that have been successful?

Thanks a lot, any help will be greatly appreciated.

Mark

Welcome to XS!

I have almost the same spec (see sig) and found that the memory divider works alot better when set to 166 or 133. 183 caused instabilty for me too and wasn't recognised in the bios post.
My system runs fine @
Memory 2.8v
2.5-2-3-6 1T on a 166 divider

CPU
opty 165 at 1.3v(+0.2v)
290x9(2.610ghz).

Chipset
K8 to NB 600mhz - all others auto.

This is with all the overvolt options enabled and EEC disabled.

Hope this helps.
12-13-2005, 06:53 AM
protocold_roid

Quote:

Originally Posted by cronic

well i just flashed to 901 and the memory still reports .5v higher with ai booster and the cpu voltage reports .035v higher. i don't know wher to check the vcore wih a dmm so i can't test, but the vcore and vdimm report the same as 703. the hypertransportt is now a multiplier which is nice. as for overclocking i won't be able to do any testing until my g skill gets here tommorow.

Howdy all, I'm new to this board and have just purchased this board as well.

What kind of G skill are you getting?
12-13-2005, 07:15 AM
cronic

Quote:

Originally Posted by protocold_roid

Howdy all, I'm new to this board and have just purchased this board as well.

What kind of G skill are you getting?

Model #: F1-4000USU2-2GBHZ
should be here in about an hour.
http://www.newegg.com/Product/Produc...82E16820231021
12-13-2005, 08:23 AM
protocold_roid

Quote:

Originally Posted by cronic

Model #: F1-4000USU2-2GBHZ
should be here in about an hour.
http://www.newegg.com/Product/Produc...82E16820231021

Nice, that's on of the non tccd sets that ben recommended. I've got that same one in my newegg basket.:toast:
12-13-2005, 09:38 AM
mhorgel

Quote:

Originally Posted by Ic3man

Welcome to XS!

I have almost the same spec (see sig) and found that the memory divider works alot better when set to 166 or 133. 183 caused instabilty for me too and wasn't recognised in the bios post.
My system runs fine @
Memory 2.8v
2.5-2-3-6 1T on a 166 divider

CPU
opty 165 at 1.3v(+0.2v)
290x9(2.610ghz).

Chipset
K8 to NB 600mhz - all others auto.

This is with all the overvolt options enabled and EEC disabled.

Hope this helps.

Thanks...this is just the kind of help I was hoping for! What is the default multiplier for your Opty? For my chip, it is 200 MHz x 11. Should I lower the multiplier and increase the FSB? Or just leave it at 11 and try to get the FSB back up to 238? Or should I play with both approaches? Will I have to do anything to my PCI-E clock?

Thanks again,

Mark

Show 100 post(s) from this thread on one page