"ASUS P5Q Deluxe discussion".

Printable View

Show 100 post(s) from this thread on one page

06-19-2008, 02:51 PM
Leeghoofd

Quote:

Originally Posted by jVIDIA

Everest mem bench please ;)

http://users.pandora.be/OAP/P5QDlx/600-1200E.JPG
06-19-2008, 02:54 PM
jVIDIA

Very nice results men. Any skews or other refined setting changed ?
06-19-2008, 02:58 PM
Leeghoofd

Skew advanced on the ram 50, TRFC from 46 to 55 at the moment but not enough to do 32MB stable at 600FSB/1200... with Skew delay I get a BSOD before entering winblows... Hope to make 600/1200 but this will take time...
06-19-2008, 03:23 PM
chispy

Lee have you tried the 0704 bios?
06-19-2008, 03:24 PM
Dr_BenD_over

OMG is the 0506 BIOS ever crappy... A nice safe 400FSB and it goes into recovery mode...
06-19-2008, 03:35 PM
chispy

Quote:

Originally Posted by Dr_BenD_over

OMG is the 0506 BIOS ever crappy... A nice safe 400FSB and it goes into recovery mode...

Try 0702 ,its way better ;)
06-19-2008, 03:36 PM
iboomalot

any suggestions on a nice Raid 0 card???

Since Iam only using one GPU ATM and thinking of doing a RAID 0 on two Velociraptors what has worked with this mobo for a fast raid card??
06-19-2008, 04:05 PM
Cob

The on-board RAID is grand for RAID0.
06-19-2008, 04:46 PM
zuess

I'm very interested in the P5Q Deluxe, I've spent a few hours trying to find out whether this board supports the Xeon E3110 cpu.

Anyone have any information on the support for E3110.

Thanks

zuess
06-19-2008, 05:05 PM
Cob

It certainly will support it.
06-19-2008, 05:20 PM
hellcamino

Quote:

Originally Posted by zuess

I'm very interested in the P5Q Deluxe, I've spent a few hours trying to find out whether this board supports the Xeon E3110 cpu.

Anyone have any information on the support for E3110.

Thanks

zuess

I am using an X3360 with it and it works well .
06-19-2008, 05:21 PM
Fitseries3

Quote:

Originally Posted by Cob

Which CPU?

400mhz FSB should be possible on the lowest FSB Term, PLL and NB voltages.

i've tried a few different chips and settings. the board goes into recovery mode when anything is set to to anything other than auto. i have e7200, e8500, q6600, q9450, e6750.

i have tried the 0702 bios as well and it always goes into recovery mode.
06-19-2008, 07:45 PM
plion

hey guys, just ordered a p5q pro, had a few questions on stability checking: any specific settings for memtest? and after testing in memtest which prime test should I run? large ffts since memtest has tested the ram?
06-19-2008, 08:34 PM
hellcamino

Run small fft's for a minimum of one hour ( preferrably two ) and if it's passing there run blend for a minimum of 4 hours but preferrably eight .
06-19-2008, 10:57 PM
Leeghoofd

Quote:

Originally Posted by chispy

Lee have you tried the 0704 bios?

Nope mate still on 0702... Seems Pmp pulled 0704 from his FTP so not worth for me to try... will mess tonite some more with the Skew settings to try to get 600/1200 done...

Quote:

Originally Posted by fitseries3

i've tried a few different chips and settings. the board goes into recovery mode when anything is set to to anything other than auto. i have e7200, e8500, q6600, q9450, e6750.

i have tried the 0702 bios as well and it always goes into recovery mode.

That's weird did you flash wiht EZ flash ? prolly better reflash and pop the battery to have a complete Cmos reset... you sure the Dimms are fine ? Plz list all ya hardware here...
06-19-2008, 11:11 PM
Chri$ch

Quote:

Originally Posted by Leeghoofd

Nope mate still on 0702... Seems Pmp pulled 0704 from his FTP so not worth for me to try... will mess tonite some more with the Skew settings to try to get 600/1200 done...

:shrug:

http://kielbaski.com/pmp/MB/ASUS_P45...ELUXE-0704.zip
06-20-2008, 12:06 AM
Leeghoofd

Thx mein Deutschen freund :) Chrisch you on 600/1200 stable yet mate ? (his previous Strony aster link wasn't giving 0704 anymore, only 0702)
06-20-2008, 12:33 AM
Chri$ch

no, not stable :(

i wait for other mem (ballistix pc2-8500 / d9gmh).
06-20-2008, 12:46 AM
71proste

Quote:

Originally Posted by Leeghoofd

K did some tests, reverted to 6 multi and started off with 550FSB/1100 ram... I left Perf levels to be decided by the bios aswell as subtimings...

DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO (is PL 13)

I ran into trouble at 590FSB... upped Ram voltage to 2.35 (max I want to give my Gskills as they worked fab at 1200mhz at 2.3v on the P35)... went a bit further, dropped PL to 15 almost completeds it's run ( see screenie ) so it could be my ram that needs some more juice ( will try later with a fan over them )... Then I tried to mess with Read Trainer and OC Charger and set them to have more clocking headroom... seemed to have inversed effect as it crashed now at ineration 8...

Will let things cool down and try again to see if I can make 590 complete ( will mess too with the Skews...and TRFC)

I tried same settings,but doesn't work on my board even with 1.6 vNB.
I don't know what to do yet.I think that's memory fault,because cpu seem to be stable(Orthos FFT's prio 9,wprime 565Mhz),but spi 16/32m as I said only 545Mhz x6 :(
Will try later with other memory's and other settings.
What about GTL settings,did you change GTL(NB,CPU) or left auto?
06-20-2008, 03:40 AM
LUCI5R

Cob, you were right. It's SpeedStep that was causing the lower Multi. As soon as I hit the 'Encode' button on TMPGEnc Xpress, Multi jumped to 8x and PC was running at 2667Mhz.

During the encode last night, when CPU Utilization was fluctuating around 90%+, CPU temperature hovered around 49. That's not bad, right? That's around full load.

A bit off this thread - I put in a little review of Q9450/P5Q at Stock from my operations last night, and I have to say I'm a bit disappointed. If anyone's interested, you can read up here: http://www.xtremesystems.org/forums/...&postcount=638 (Especially video encoders).
06-20-2008, 03:58 AM
hellcamino

That is too bad that you were so disappointed , I have found my X3360 ( Q9550 ) to hands down beat my Q6600 in any given benchmark clock for clock . The only other change there is that the new cpu runs as fast 24/7 as the Q6600 would for benches only giving it even more of an edge .
06-20-2008, 04:10 AM
Cob

Well clock for clock the Q9450 is only about 10% faster than the Q6600. But it comes into its own in software with SSE4.
06-20-2008, 04:12 AM
LUCI5R

Quote:

Originally Posted by hellcamino

That is too bad that you were so disappointed , I have found my X3360 ( Q9550 ) to hands down beat my Q6600 in any given benchmark clock for clock . The only other change there is that the new cpu runs as fast 24/7 as the Q6600 would for benches only giving it even more of an edge .

I guess, thing is - the PC is definately, no-contest, running a LOT faster & smoother then it ever did. In fact I was blown away with the Start Up, especially with the ton of 'Start Up' applications that load in the system tray - that used to take forever - now it was like all within 30 - 50 seconds, which is tremendous.

And like I said, while Unraring a huge 8 GiG file, I'd have to wait before even hitting the Start button cause it would at times, inadvertently hang! So all those things are real pretty now.

But what I really upgraded for was Video Encoding, Editing and such audio/video related jobs. (I do website design/development as well, thus Adobe CS3 will come into picture - but I didn't really test it out yet. Judging by how fast Applications were opening & closing, I'm assuming it'll be blitz!). And at stock speeds I really wasn't thrilled.

I'm not sure if you compared at Stock, and not sure if you did any video encoding jobs, so that could be the difference. I saw a lot of review at Newegg by Video Encoders who were satisfied - but again, they didn't go into details - and there's a huge difference encoding a mid-res xvid to divx or dvd and encoding an HD h.264 to WMV-HD (VC-1) or Blu-ray Remux.

I'm not disheartened yet. OC'ing is on it's way. With my E6420/P5W/2GB PC2-5400, I hit a wall very early on around 350-360FSB, getting up to 2.8Ghz only. I'm expecting better results with PC2-8000/P5Q (P45) & Q9450.

Quote:

Originally Posted by Cob

Well clock for clock the Q9450 is only about 10% faster than the Q6600. But it comes into its own in software with SSE4.

Honestly, SSE4 was the primary reason I spent 75% more on Q9450 (over Q6600). From whatever I had read, SSE4 was supposed to bring this drastic difference in Video Encoding. Both software I use primarily for Video Encoding/Editing (TMPGEnc Xpress Mar.08 release, MS Expression Encoder) have full SSE4 Support - and some others that don't (Vegas Pro, ProCoder) are set for new releases shortly with SSE4 support. You're right about clock-for-clock, that's what most people say. But I put my money on SSE4.
06-20-2008, 04:28 AM
Cob

Remember also that your hard drive is the slowest part of your system, and will stiffle some of the gains when working with large files. Going to RAID0 may give a bigger boost than SSE4.

Have you run the WinRAR benchmark on both chips to see the differences between the 2 chips?
06-20-2008, 04:31 AM
LUCI5R

Quote:

Originally Posted by Cob

Remember also that your hard drive is the slowest part of your system, and will stiffle some of the gains when working with large files. Going to RAID0 may give a bigger boost than SSE4.

How do you setup RAID0? Do you need two hard drives for that? Can you point me in the right direction to reading a bit more about this - something for a somewhat n00b. I've never experimented with RAID0 before.

Quote:

Originally Posted by Cob

Have you run the WinRAR benchmark on both chips to see the differences between the 2 chips?

That's a mistake I did make. I should have saved benchmarks from my previous chip. I don't have any actual numbers from my system to do an actual comparison. I'm just going off my physical memory/experience.

Show 100 post(s) from this thread on one page