Printable View
i dont understand this my temperature..where is problem?...
http://img218.imageshack.us/my.php?image=hhhhko1.jpg
my temperature is 11C i don t understand this...why...?..please help me..where is problem?..cant be 11 C
Mb has 38C
NB has 50C
SB has 47C
and processor has still 11C
showing in bios...core temp..asus probe..everest...:mad:
You're so lucky :p: use coretemp 0.96.1Quote:
Originally Posted by UnSeenSVK
can be problem with cpu?..
yes that showing me...in windows about 22C..is it ok?
Only 1 core displaying in Core temp you better check thatQuote:
Originally Posted by UnSeenSVK
CN :)
you right .. now is displaying Core 0 and Core 1 core one has 22C and core 0 has 14C...
Got a Q750A too.Quote:
Originally Posted by karateo
Karateo can you post your bios settings for your 4Ghz and up clocks.
read upto page 11 so if asked since then sorry :P
nice results Bail :up:
Anyone got one of these from zipzoomfly, good batch?
Of course, i'll be ordering in the morning and newegg goes out of stock today :down:
used same everest..shows 11C...
core temp 0.96.1 showing core 0 12C core 2 16 ....
when i running 3dmark06 core 0 shows... 17C and core 2... 16C
look
http://img85.imageshack.us/my.php?image=ddddui7.jpg
how is his possible?
heh guys whats the most desired week E8400 so far? 45 or 46
Weird, I reset all the settings the same as I saved it all in CMOS reloaded.Quote:
Originally Posted by eva2000
I ended up flashing the BIOS to 1/11/2008 and then dropping GTL settings VERY low compared to what I have for my QX9650.
VID @ 1.1 (or 1.2? I forget) and GTL settings @ 40/50/60... now it's Priming like fun.
WEIRD!!!!!!!!!!!!!
check this outQuote:
Originally Posted by WiTcHkInG
http://csd.dficlub.org/forum/showthread.php?t=5467
:up:
I got one from zzf yesterday, Q743A756. I've seen 3 Q743's posted. 2 were at 4G and the other at 4.5G. All were on air. I'll probably try this one out tomorrow.Quote:
Originally Posted by ThatGuy16
nice, i have always ordered from newegg. So it will be my first ZZF purchase, assuming they will still have them in stock in the morning :p:Quote:
Originally Posted by PhilDoc
i use Aircooling core idle 49/51 change over to water still 49/51 i don't really know what is going on, unless my water cooling is :banana::banana::banana::banana:. I touch the water block base it not even warm.
I like the egg a little better, but they charge me tax, so I've ordered from zzf quite a bit over the years and they've for the most part been excellent. Their prices are usually very good and I like the free shipping. It was even better when they were shipping free 2nd day air.Quote:
Originally Posted by ThatGuy16
Almost every board is giving wrong temps for the E8xxx
Don't worry about it for the time being until a new BIOS or software to get a correct reading.
It just does not want to go 500 on the FSB. LOL. Will do 499 but not 500. Anyway, here is my SuperPi
Merc/10.312s/P5K Deluxe/Core 2 e8400 @ 4491MHz/5-5-5-10 2T (624MHz)/Water/01-31-08
SUPERPI TO 1M 10.312s
http://img231.imageshack.us/img231/2...0312kp5.th.jpg
Vcore is 1.4625v in BIOS and 1.44 during Pi. I'm at that wall where you have to throw voltage at it so I'll go there tomorrow.
Did you try 501? Maybe it just doesn't like 500.
Yeah. It will boot and everything but I get "SuperPi encountered an error and must shut down" and then it hangs there and will not close. My buddy hit the same wall with the same board so possibly it is the board but he is throwing 1.6v+ at it and got Pi to run. Not sure i want to go there with this 45nm chip but we'll see. The temps are fine as far as I can tell.
If it's just for a quick bench, I don't think there'll be an issue throwing more voltages - doesn't do much harm unless you're putting 2V, lol.
Ahhh, this is more like it Q745A576 - 1.16875 v set in bios
http://img98.imageshack.us/img98/650...lowvha4.th.jpg
more -
http://img168.imageshack.us/img168/5...lowvmz6.th.jpg
Also 3dm06 and 05 run fine. Here is just after running 05 -
http://img232.imageshack.us/img232/6...wv05nj4.th.jpg
I have older 8800gts 320
I hear ya and I know I'll be pushing the Vcore tomorrow. :DQuote:
Originally Posted by aoch88
45nm dies and degrades quick. 1.45V is the limit air without definitive damage and you have no way to verify temps, but they will be very high with >1.4 on air as stock is around 50C loaded at 3GHz 1.1V. I've already returned the first batch we had at work since they all read completely wrong temps, now waiting for the 2nd one.
My temp readings are bad as well. The chips seems to be running cool, though, as i feel almost no heat coming from my rad ( I am on water). Not having a good indication of temps is disturbing though. I hate to RMA such a good clocker but it is worthless on the resale market as is.Quote:
Originally Posted by KTE