Printable View
I got mine from ewiz and is also U7150xxxx. I might be in the clear though. I'm using my different sticks of gkx in the blue slots now instead of white, and while these sticks are requiring 2.2v which I'm giving them, I seem to be having the longest streak of stability ever. I'm on large going on 12 hours now. This beats my old record of large/blend for 6.5hrs by about double. I hope I'm in the clear and that by tomorrow, when I wake up, it'll still be going strong :). Wooo
I'm not testing as thoroughly, but serial's U71200731 from William @ DFI. This thread needs more hardware pics. :D
ahhh, probably the best from william ;)
Thank you The Nemesis,Quote:
Originally Posted by The Nemesis
but I don't think my problem is tRFC because when I change vdimm to higher values my system is more unstable. If I put vdimm to 2.0 or 2.1 Orthos runs 15-20 min without any problem, but when I put 2.2 or 2.3, in two or three seconds my system stops. Sometimes with this vdimm windows don't start.
I think RMA the motheboard, but my problem is the blackplate of TR ULTRA 120 that seems to be impossible to unhook from the motheboard.
Does anyone know how do it ?
you have prometheus or elpida chips, stay 1.9 to 2v, most of this ram tops out @ ddr990 to 1000, however it gives good bandwidth despite the looser timings..
Genie BIOS Setting
NB Strap Select 266
Exit Setup Shutdown Mode2
CPU Clock Ration 8 X
CPU Clock 463
Boot Up Clock Auto
DRAM Speed 533
PCI Clock 100
Auto Detect PCI Clk Disable
Spread Spectrum Disable
CPU Feature
Thermal Management Control Disable
Limit CPUID Maxval Disable
PPM Function Disable
C1E Function Disable
Execute Disable Bit disable
Virtualization Technology disable
Frequency Nolimit Disable
Voltage Setting
CPU Voltage Setting +225.0mV (1.5v)
DRAM Voltage Setting 2.200V
VTT Voltage Setting 1.19 V
NB 1.25V Setting 1.40V
SB 1.5V Setting 1.5V
SB 1.05 Voltage Setting 1.05V
DRAM Timing
DDR Configuration Mode Auto
GTL+ Driving Strength Mode2
Enhance Data Transmitting Fast
Enhance Addressing Fast
DQ Calibration 5
Channel 1 CLK fine delay Auto
Channel 2 CLK fine delay Auto
CAS Latency Time (tCL) 4
DRAM RAS# to CAS# Delay (tRCD) 4
Precharge dealy (tRAS) 12
All precharge to Act Auto
REF to ACT Delay (tRFC) Auto
MCH ODT Latency Auto
Write to PRE Delay (tWR) Auto
Rank Write to Read (tWTR) Auto
ACT to ACT Delay (tRRD) Auto
Read to Write delay (tRDWR) 8
Ranks Write to Write (tWRWR) 6
Ranks Read to Read (tRDRD) 6
Ranks Write to Read (tWRRD 5
Read CAS# Precharge (tRTP) Auto
All PRE to Refresh Auto
i dont really recommend 1.6 for 24/7, but 1.55v is fine.
@yenclas
As raju has already stated, the chips used for your memory are Elpida. Above 2.1V is definitely going to cause stability problems.
My board reaches 500FSB pretty easily. Over 500 I have to increase voltages slightly, but still no real problems.
Got it from eWiz. SN: U71200700
If you would, write down your BIOS settings and post them here like the others have so we can continue to compare settings with different memory modules. I'll post mine once I have a chance to find max clocks with 4x1GB.Quote:
Originally Posted by Dark79
Genie BIOS Setting
NB Strap Select Default
Exit Setup Shutdown Mode2
CPU Clock Ration 7 X
CPU Clock 515
Boot Up Clock Auto
DRAM Speed 533
PCI Clock 100
Auto Detect PCI Clk Enable
Spread Spectrum Disable
CPU Feature
Thermal Management Control Disable
Limit CPUID Maxval Disable
PPM Function Disable
C1E Function Disable
Execute Disable Bit Disable
Virtualization Technology Disable
Frequency Nolimit Disable
Voltages
CPU: +100.0mV (1.425v)
RAM: 2.10V
VTT: 1.20 V
NB: 1.35V
SB: 1.5V
SB: 1.05V
DRAM Timings
A-Mode2-Fast-A-A-A-A-5-5-5-12-5-25-2-11-10-3-8-6-6-5-4-5
Lol, this board is so friggin weird its not funny.... I finally got it going at ~540fsb ( 7x) with fast settings and I thought I had it all figured out but then when I move to 8X I couldnt do :banana::banana::banana::banana::banana:...... Using 2 stix or ram is ok but Ive tried all possible combo and I cant run all 4 stix together at 500fsb...... Couple of things Ive noticed, this board dont like 5-5-5 timings and also its really picky with how much voltage you give it..... Also it loves corrupting my hd lol......
This board is as good as everyones said BUT it needs to be tweak properly and the margin of error in the settings is very small.....
raju,Quote:
Originally Posted by raju
are you sure that GSKILL DDR800 HZ's don't have Micron D9 chips ?
I thought that this memory always have had this chips.
Well this board just killed one stick of the best ram I own:mad:
Yeah they do have D9GMH or possibly D9GCT, but thats unlikely.Quote:
Originally Posted by yenclas
ouch :(Quote:
Originally Posted by The Nemesis
How much voltage when it died?Quote:
Originally Posted by The Nemesis
it should be d9, but the fact it does not like more than 2.1vdimm points to other chips, I don't know personally as the behaviour of more voltage than 2.1 = less stability is definitely prom/elpida behaviour....Quote:
Originally Posted by yenclas
I guess you will have to find out from gskill..
or you might have dying ram, that would explain the problem....
regards
raja
Only 2.3, I was switching from the crucial anniversary to my high binned G. Skill 6400 HZ's. These sticks did DDR2-1200 5-5-5-12 2.3v on Abit IN9 32-Max so I've never put more than 2.3 on them. Though I had powered off the board, removerd power to psu, & press the power button on the board to dissapte any remaining current I can only assume there must've been some left. I was already being very careful with this board as it seemed to stay powered longer than others. Guess I wasn't carefull enough. First time I've ever killed ram exchanging modules. I'll try the freezer I guess.Quote:
Originally Posted by burningrave101
Nemesis, did u perhaps change the GTL (drive strenght)?
will promos ram run well on this board? (g.skill white heatspreaders)
What is command in the bios to put the memory on 1T?
Also, im not using any IDE devices. Where in the bios can you disable the IDE controller so it will not effect my overclock ?
Quote:
Originally Posted by The Nemesis
welcome to the club 1 corsairs stick also dead :slapass:
don't think it's possible to use 1tQuote:
Originally Posted by rfisher983
man...sorry to know the memory stick is dead from a couple of you.
This is really scary...I hope this mobo is not overvolting the ram modules than what we actually set.
Can anyone please explain what's the true purpose for setting GTL+ driving strength?! I read the info on this is related to quad-cores but yet I still some of you change it to mode 2 with a C2D. Is it absolutely necessary to gain stability at for higher CPU or RAM clock speed?? Any performance gain from Auto to mode 2??
I have my OCZ PC6400 OC'ed to about ~930 on 1:1 but even at this clock speed, I absolutely need to set MODE 3 for DDR configuration. According to the OC guidelines from FCG and DFI club, Mode 2 is needed for +1000 and Mode 3 is needed for +1200...and in my case it's totally different. So the overclocking guide specific configuration explanation is probably not the standardized guideline for all.
I did. Did that kill it? Or are you saying change it back for the stick to boot because I cleared the cmos after the sticks wouldn't boot. Tried both and the screen turns on, stays black. Tried each stick by itself, one boots the other gives dreaded 3 beeps.Quote:
Originally Posted by RealTelstar