Have you tried LLC disabled?Quote:
Originally Posted by angelreaper
Also, what were the load temps on that 4200Mhz overclock you showed?
Printable View
Have you tried LLC disabled?Quote:
Originally Posted by angelreaper
Also, what were the load temps on that 4200Mhz overclock you showed?
cod4 and cod5 work fine for me with PB ....
With Win 7 RC 64bit? Doubt it unless you're going to servers with a very lenient PB setup, which I tend to stay away from.Quote:
Originally Posted by Rattle
Just played around 3hours of COD4, across 3 different servers and no PB issues at all. Perhaps the lazy ****ers have decided to acknowledge W7 early, who knows, but at the mo, it seems to work ok :D
On topic, got my UD5 running BIOS f8b with my i7 920 D0 at 3.6 (18*200) @ 1.2v (1.17v in windows).....is that considered a 'normal'-ish voltage for 3.6??
Anyone?Quote:
Originally Posted by roadtonowhere08
Yes bud drob becomes huge:shocked:Quote:
Originally Posted by devsk
Temps:
http://img30.imageshack.us/img30/2076/linx4200.jpg
Nothing new there with the vdrop. I think the vreg nearly the same as the ep45 even the vdrop mod is the same. Either enable LLC , vdrop mod 5k ohm with LLC off or the pencil mod.Quote:
Originally Posted by angelreaper
only had i950 for half hour, and 5th boot, but so far loving it...4.6 ghz 1m spi stable at 1.376 vcore.
Edit: holy crap this chip is hot. I think I could run 4.5ghz 24/7 if could control temps. I started linx 5gb, came back it was on the 4th pass, temps were already 95C. Tried prime, 5 mins into it 88C...not running that o/n on my new cpu. So much for 25C ambients, 6 scythe push/pull at 1500rpms on dedicated cpu loop with PA 120.3, my i7 is laughing at it.
http://img198.imageshack.us/img198/1...6001376spi.jpg
nice temps with 1.376 vcore :rofl:
http://img177.imageshack.us/img177/9...5001376pst.jpg
Thanks for the info. My ambient is also same and my cooler is also same. So is the CPU (W3520). So, I can expect similar results. Barring, my chip is a dud! Which it is not because I had it at 4.32 on the Asus P6T dluxe. I am just waiting for UD5.Quote:
Originally Posted by angelreaper
I'm considering getting a Core i7 950 with the UD5, and I got a question. Whats the stock volts for the 950 and whats the max multiplier you can use? Also I'm aiming for 4Ghz on air if I get it and what kind of volts do I need to stabilize the 950?
Its okey...but i think you can get it highet without much more volt, i run my 920 D0 on 4ghz-1,2v prime stabil:DQuote:
Originally Posted by Jonny Manc
Have you tried 4ghz with 1,2v under load in win.?
rge what stepping man?
My batch # 3847B005, got it from newegg.
Thanks for that :DQuote:
Originally Posted by The Water Dog
Not tried any higher yet, waiting for some new fans to be delivered (Monday I think) and need to reseat my TRUE with the washer mod (unexplicably forgot to do it when I got my i7 :shocked:). Once its all re-done, I will try for more.
Snipped in case Gigabyte would get upset, I will ask and then add back if they do not mind.
I like the EX58-UD5 , its very easy to OC and rock solid stable mobo
I'm running my CPU @3.8 v1.12 and my memory @1900 v1.64 Only :)
I also reached 4.0 very easy ( 20 X 200 ) and its very stable , but 3.8 its just fine for my games :D
Was changing the paste on my cpu the other day when i accidently bent a few pins in the socket :shakes: so i've ordered a replacement. Is it a problem to take out the bios chip from the old board and put it in the new one?
what QPI and IOH volts?Quote:
Originally Posted by koc
Those temps might be fixed with a better block/rad combo. Nice clocks man!!Quote:
Originally Posted by rge
Thanks, yeah my delta from air intake 26.2 C to water 32.1 C = 5.9C. I would need a Quad rad or 140x3 to get maybe another 2-3C or delta down to 4C is about the best I could do with fan speed I am willing to use, 1400 rpm 6/push/pull, and maybe another 1-2C with heatkiller, but they are out of stock everywhere. About 4-5C I could gain which would definitely help, 83 would make me much happier than 88 load. I have reseated 4x all within 1C of each other. Biggest issue is 50C delta between water temps and core temps vs 40C delta I had with my i940, not sure if all that is just hot cpu or some of it is IHS/block contact non-ideal.
So far I am settling for 4.4 prime 13hrs stable with vcore 1.34, at least temps are reasonable.
http://img41.imageshack.us/img41/297...primeposta.jpg
a little game on the air
EX58-EXTREME
i7 950@4738MHz air
295GTX@761/1640/1208 air
3Dmark 03 ...105433 :)
http://img244.imageshack.us/img244/5...ure7custom.jpg
EX58-EXTREME
7 950@4738MHz air
295GTX@761/1640/1208 air
3Dmark 05 ...40648 :)
http://img195.imageshack.us/img195/1...ure2custom.jpg
EX58-EXTREME
i7 950@4537MHz air
295GTX@715/1541/1215 air
3Dmark 06 ...29186 :)
http://img132.imageshack.us/img132/2...186customa.jpg
EX58-EXTREME
i7 950@4531MHz air
295GTX@763/1645/1216 air
3Dmark VANTAGE ...24909 :)
http://img198.imageshack.us/img198/2...ure8custom.jpg
I only changed the CPU and Ram volts , all author volts set to AutoQuote:
Originally Posted by Rattle
Quote:
Originally Posted by roadtonowhere08
Okay, I got them to be detected by setting the BIOS to RAID instead of AHCI. If I do this, will I still be using AHCI even if I am still using a JBOD configuration? I NEED to be using AHCI according to Intel for my X25-E.
Anyone knows when the beta bios (F9x) referred in this thread: http://www.xtremesystems.org/forums/...d.php?t=225264
will be released?
My rig is waiting for such a boost :D
http://img5.imageshack.us/img5/8102/w35204400.jpg
http://img5.imageshack.us/img5/7482/w35204600.jpg
Bclk is almost @ "the wall" (without PCIe tweaking, which I will test in a few hours)
Btw, I also tested the F8bmod bios (with the new AHCI rom) but I lost some options so I reverted to F8b normal.
Those 4Ghz+ benchmarks on air, are they stable? To reach that high on air is quite impressive even if it wasn't stable.
Those temps are way better!!!Quote:
Originally Posted by rge
I'm glad I bought my HK and the TFC x360 when I did :D
If the heat continues to be a problem, feell free to send me that 950 and I will keep it cool for you :rofl:
Hi mate. New to this and could use some help.Quote:
Originally Posted by koc
Tried following giga's guide to 4Ghz found here (vcore 1,4v) and couldnt post.
I just want to reach 3,8-3,6 and be ok for now. (Summer being really hot in Greece.I have like 31-33 C ambient right now :) )
If you could spare me some time, could you post the exact changes you made in your bios to reach that nice overclock?
I have the F7 bios, which one do you use?
Any suggestions on xmp profiles when OCing? should it be disabled?
And what are the stock MHz for your memory; 1900 sound hard for me to reach with the 1600MHz sticks I ve got which btw reach 1600MHz only with xmp enabled, otherwise they run at 1066...
Thanks in advance mate.
Memory run 1066 if you have everything on stock:)
But 1600 its enough for 4ghz, but what did you sett on the vtt-volt?
I running UD4P with F8 bios and running 4ghz on 1,2v vcore and 1,27vtt. The same settings on F7.
Did you remember to sett qpi link speed to X36 and sett Uncore to 2+1 ( if you have choose 6 on the memory you have to set 13 on uncore)
I did exactly as suggested by gigabyte's guide.
vcore 1,4v , vtt 1,5-1,52v .
C1E, xmp, intel turbo, all disabled.
Memory x6, uncore 13, qpi x36.
:(
Their guide is bunk dude. That VTT voltage is unnecessary and that vcore is for C0 920's not D0's.
yeah, the voltage in that guide is to high, If you have a D0 that need 1,4vcore under load , i will say you are a realy unlucky dude.
ORLY?Quote:
Originally Posted by ReverendMaynard
when u try last? gimme a server for either and i'll go there now
:rolleyes:
LOL...yeah, I actually am planning a new case just to cool my i7 better...not to mention in future when 16 core versions/32nm comes out...cant wait to see how hot those will be, regardless of what intel states about increased power efficiency, which obviously goes out the window with OCing.Quote:
Originally Posted by hlonipha
I will try the HK as soon as one comes in stock somewhere, and getting one of these cases (link below) if they ever get built...and put a quad rad up top just for i7, and video cards will do fine with 360.
http://www.xtremesystems.org/forums/...d.php?t=219974
yea that case is very nice hopefully he goes to production with it. I will get one as well. I want a monsta quad rad and the x360 to cool my GTX 295's as well. Until then, my HAF 932 will have to do.Quote:
Originally Posted by rge
I've modded the Extreme F8x BIOS and updated the Intel AHCI ROM to 1.20E and Intel RAID ROM to v8.5.0.1030
I tested it by flashing it to my UD5, and AHCI is working great.
If anyone would like to try it:
http://wright-pc.com/pyr0/UD5/EX58_Mod/EX58EXm.F8x
I need to learn what AHCI means :confused:
4.0 and rock solid
http://www12.0zz0.com/2009/06/09/19/358781536.jpg
:up:
That is some nice low volts for 4ghz koc...I'm at 3.6ghz on the same volts (1.5v in BIOS??), wonder if it'll get me to 4ghz??
wow 1.5v for 3.6 :eek:Quote:
That is some nice low volts for 4ghz koc...I'm at 3.6ghz on the same volts (1.5v in BIOS??), wonder if it'll get me to 4ghz??
i run 3.8 with 1.1v only and 4.0 with 1.2 only in the bios and its very stable
you dont need more than 1.2-1.3v for 4ghz
Hi nikolas61;
I notes that your CPU @4537 and score 24141 in 3Dmark VANTAGE
And my CPU @4.0 and score 53185 in 3Dmark VANTAGE
http://www5.0zz0.com/2009/06/09/21/483297783.jpg
am i wrong or what ?
That's because you have physx enabled, he doesn't. People who disable it, usually submit their scores to hwbot where it is an illegal setting.Quote:
Originally Posted by koc
I was wondering if I could get some help in the right direction with my Extreme board. My system specs are listed in my sig, but to start off, using my old DFI UT x58 and ASUS P6T6 I was able to get my rig to post at 20x192(with turbo mode on, so I guess 21x) no problem. For that setting I used 1.325v vCore, 1.3v VTT, 1.8v PLL, 1.8v DRAM, and about 1.26v for the IOH (not ICH). Ram I would leave on Auto timings and start at the lowest multi/speed listed in bios (generally under 1200MHz). Now using these settings with bot the DFI and ASUS I got the board to post up to 21x216 with out a problem, but now, those settings don't even post. My D0 I got second hand from someone who using a Gigabyte Extreme was able to get this chip to do 4.62GHz, so I know the problem most likely is a BIOS setting, but since I am unfamiliar with some of the new terms and general layout of Gigabyte, I'm not sure where to start, so any help would be greatly appreciated. Thanks in advance.
Where did you get F8x bios? :eek:Quote:
Originally Posted by Pyr0
Is this the one with improved bclk ?
I've tried the mod version of F8b but i've lost some dividers therefore I returned to the regular F8b. With this F8x mod happens the same?
Thanx
Would help if I could type...should have read 1.15v :rofl:.Quote:
Originally Posted by koc
well , i disable the physx and i score 24921 for the CPUQuote:
That's because you have physx enabled, he doesn't. People who disable it, usually submit their scores to hwbot where it is an illegal setting.
i think this is fair result :)
Pyr0, you rock!! :p:Quote:
Originally Posted by Pyr0
Saved me some time doing that myself (was still waiting to get F8X mailed to me) :D
Yeah Pyr0 you do rockQuote:
Originally Posted by Arcanum
aka "THE MAN"
Day :p:
your result is ok.Quote:
Originally Posted by koc
i disable the physx and i score 27534 for the CPU @4531MHz.
:wave:
You're result is average at best for those clocks :up:Quote:
Originally Posted by nikolas61
wow... so I tried to work with bios f8b and then f7 with nothing but horribleness. I would get the bioses loaded and start fresh from a clean slate then trying to get my old OC settings stable was a disaster... f8b went into a boot post loop every time I would even get half way through my bios configs... I would have to full power the mobo down (power out of the psu) to get it to stop. f7 made it through all the configs but windows would not load... after several hours of this I gave up and went back to f5e. Also, 7f was going the same damn multi-post thing making my areca raid card beeping like a smoke alarm in forest fire... the whole reason I wanted to get a new bios was to avoid that... so I guess all of these gigabyte bioses do this when the board is overclocked?? I am thinking about soldering the buzzer off the raid card at this point. sheesh!
what are you comparing this run to?Quote:
Originally Posted by ReverendMaynard
sorry mate i didn't notes your post :)Quote:
Originally Posted by javaneze
speaking about summer , we are Toast here in Kuwait , but Swimming helps a lot, to bear the summer heat :surf:
Any way back to the topic , i also followed giga's guide to 4Ghz , but i changed some settings for more stability
My first OC @3.6 with these settings
Advanced CPU Features:
CPU Clock Ratio ................................ [20x]
Intel(R) Turbo Boost Tech ...................... [DISABLED]
CPU Cores Enabled .............................. [All]
CPU Multi Threading .............................[Enabled]
CPU Enhanced Halt (C1E) ........................ [DISABLED]
C3/C6/C7 State Support ......................... [DISABLED]
CPU Thermal Monitor ............................ [DISABLED]
CPU EIST Function .............................. [DISABLED]
Virtualization Technology ...................... [DISABLED]
Bi-Directional PROCHOT ......................... [DISABLED]
Uncore & QPI Features:
QPI Link Speed .............................. X36
Uncore Frequency ............................(20x)
Isonchronous Frequency ......................[Enabled]
Standard Clock Control:
Base Clock (BCLK) Control .......................... [Enabled]
BCLK Frequency (MHz) ................................[180]
PCI Express Frequency (MHz) ........................ [Auto]
C.I.A.2........................................... .. [Disabled]
Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [700mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]
Advanced DRAM Features:
Performance Enhance ...................... [TURBO]
Extreme Memory Profile (X.M.P) ........... [Disabled]
System Memory Multiplier (SPD) ........... [10.0x]
DRAM Timing Selectable (SPD) ............. [Auto]
and the last thing the volts :
set all the volts to Auto except Vcore , set it to 1.125
and Dram voltage as same your memory spec.
With these setting your memory will OC@1800 , So. you need to rise the volt to 1.66 or 1.7 and keep the timing at auto for more stability and change the timing after you successfully post to the window
my memory stock speed 1600 with timing 7-8-7-20 , and i reached 2000 with timing 8-8-8-24 at 1.68v
Also i used F8b bios
Hope these setting help :up:
Thank you for your time and answer.
I will give the settings a try and get back for some feedback.
Again, thanks! :)
any one running G.skill F3-16000CL8T-6GBPS ? Perfect Storm or w/e its called
2 question!!!
cpu auto fan regulation works with 3 pin fan? or only with 4 pwm pin?
dominator 3*2gb 1600mhz works good on UD5?
tank's to all people!
1.YES/cpu auto fan regulation works with 3 pin fan and 4 pwm pin/Quote:
Originally Posted by Andrea deluxe
2.YES
Hi,
Rig Set up:
Intel Core i7 920 D0 Stepping (SLBEJ) 2.66Ghz
OCZ Gold 6GB (3x2GB) DDR3 PC3-12800C8 (1600MHz) Tri-Channel
System is water cooled and shows as around 27c in bios idle.
OC settings are as per the pics below for a 4GhZ OC.
I purchased this set up as a pre OC'd bundle from overclockers.co.uk.
I wanted to ask if these settings was the best and should I be concerned about anything set. It is more curiosity since the OC has not been done by myself.
Feed back please?
http://farm4.static.flickr.com/3543/...6312436803.jpg
http://farm4.static.flickr.com/3405/...69c21b9711.jpg
http://farm4.static.flickr.com/3649/...749c124625.jpg
Thanks
Whats the RAM specs cos those timings look loose for the frequency (1528)!?
Also, you might get lower vcore for 4ghz (some D0's are as low as 1.15v :O)
I get a BIOS ID error. How do you manage to flash the UD5 with this?Quote:
Originally Posted by Pyr0
Thanks for replying...Quote:
Originally Posted by Jonny Manc
Specs are...
- 1600MHz DDR3
- CL 8-8-8-24 (CAS-TRCD-TRP-TRAS)
- Gold Z3 XTC Heatspreader**
- Lifetime Warranty
- 1.65 Volts
- 240 Pin DIMM
http://www.ocztechnology.com/product...triple_channel
Heyz so whats new on the new bios? i havent updated since F7c :)
it is better to set the uncore speed to 4x the memory speed?
Hi All
Finally got my i7 to 4ghz and passed 1hr 15min in prime max temp 72c.
On the mobo there are loads of LED's which i have looked in the manual and all are explained except one near the CPU on top of the bored manual says it cpu temp and green is 60c and red is 80c (or something close) Mine are on Green with an amber(no mention of amber anywhere) one next to it these are on all the time even on idle which is 50 max. idea please?
Guys, it is ok to leave all settings on AUTO, just changed the CPU vCORE, DDR3 Voltage and QPI/VTT?
I see the IOH voltage scale up with the QPI/VTT from QPI/VTT=1.28v and up. You might want to fix it. Othwerwise it ok to leave on Auto except the one you mention.Quote:
Originally Posted by phsinc1
Quote:
Originally Posted by MonsterDK
Thanks for replying...Quote:
Originally Posted by Jonny Manc
Specs are...
- 1600MHz DDR3
- CL 8-8-8-24 (CAS-TRCD-TRP-TRAS)
- Gold Z3 XTC Heatspreader**
- Lifetime Warranty
- 1.65 Volts
- 240 Pin DIMM
http://www.ocztechnology.com/product...triple_channel
So are the screenies loose then like mentioned?
Thanks.
QPI/VTT is set manually to 1.335vQuote:
Originally Posted by Sparda
I check with ET6 and IOH Voltage reads 1.100
Yeah, they do seem a bit loose.Quote:
Originally Posted by MonsterDK
They are set to 9-9-9-28 CR2 at 1528, yet the timings (from OCZ) are 8-8-8-24 CR1 @ 1600.
If you change your BCLK to 200 and alter your clocks via your mutli, this will allow your ram to be run at 1600 (stock) and change the latencies to match the stock, but ensure you put your RAM volts to 1.6v (you may even need 1.65v...but my GSkill run well at stock 1.6v :D)
WHat bios do you guys recommend? im using the F7c for my UD5
Thanks
On f8b and working well so far (I am not using RAID or AHCI though ;))
Yep you set 9-9-9-28, change those to 8-8-8-24, then command rate to 1T instead of 2T. Memtest thoroughly plz. Next up is to tweak the uncore it's prolly at sub 3200, try to go as high as possible there...Quote:
Originally Posted by MonsterDK
Nice CPU mate, hope she runs flawlessly
Hello, having problems with my OC....
The below is 'stable' (9hrs prime), but im not happy with the voltages especially considering this is also a D0, and of course if i could go faster, obv a bonus, any things to try?
Multi.................... 20
Turbo .................... Enabled
Speed.................... 4011
CPU Multi Threading.................... Enabled
CPU Enhanced Halt (C1E).................... Enabled
C3/C6/C7 State Support.................... Disabled
CPU Thermal Monitor.................... Enabled
CPU EIST Function.................... Enabled
Virtualization Technology.................... Enabled
Bi-Directional PROCHOT.................... Enabled
QPI Link Speed*.................... 36
QPI Link Speed (MHz).................... 6876
Uncore Frequency.................... 17
Uncore Frequency (Mhz).................... 3247
Isochronous Support.................... Enabled
Base Clock (BCLK) Control.................... Enabled
BCLK Frequency (Mhz).................... 191
PCI Express Frequency (Mhz).................... 100
C.I.A.2.................... Disabled
CPU Clock Drive (mV).................... 800
PCI Express Clock Drive (mV).................... 900
CPU Clock Skew (ps).................... 0
IOH Clock Skew (ps).................... 0
Performance Enhance.................... Turbo
Extreme Memory Profile (X.M.P.).................... Profile1
System Memory Multiplier (SPD).................... 8
Memory Frequency (Mhz).................... 1528
DRAM Timing Selectable (sPD).................... Auto
CL.................... 8
tRCD.................... 8
tRP.................... 8
tRAS.................... 24
CMD.................... 1
Round Trip Latency.................... 60/62/62
tRC.................... 41
tRFC.................... 88
tRRD.................... 6
tWR.................... 12
tWTR.................... 6
tRTP.................... 6
LoadLine Calibration.................... Enabled
CPU Vcore.................... 1.36875
With vdroop.................... 1.312
QPI/VTT Voltage.................... 1.375
CPU PLL.................... 1.8
PCIE.................... 1.5
QPI PLL.................... 1.1
IOH Core.................... 1.1
ICH I/O.................... 1.5
ICH Core.................... 1.1
DRAM Voltage.................... 1.68
BIOS.................... F8b
CPU.................... D0 3850A795
RAM.................... Corsair Dominator 1600
PSU.................... HX1000
Thanks ahead
That wierd.Mine is at 1.28v in ET6 when i set it on Auto with QPI/Vtt 1.475v and speed at 21x217. Will check again if any other setting might effect it.Quote:
Originally Posted by phsinc1
I see your QPI/VTT is set to Auto, check with ET6 the correct valueQuote:
Originally Posted by MonsterDK
Should i use the latest bios for my UD5 or stay with the F7c? im using a 920 C0
my current settings, Uncore 17x / memory 8x / vcore 1.23v / qpi/vtt 1.335 / memory 1.62v / HT ON / turbo boost disabled .... all other settings set to auto:
http://i41.tinypic.com/2a9blv8.jpg
coretemp 75/75/70/70, any comments?
is that a normal behavior? only happen after shutdown and power on
when I power on my PC, I could hear like 3 resets happen (the blue led behind the ram which show your OC level turn off and on like 3 times) it doesn't shutdown and power on again, it just doing like 3 reset in the row without any shutdown, I entered the bios after, but it doesn't say anything about reverting from bad OC, and every stress test passed fine.
Can someone help me on my OC im using bios F7c and i got it up to 3800 i have a C0 920, i would appreciate some help thank you.
This is normal behavior for this board.Quote:
Originally Posted by boldenc
I'm not sure what you mean by this exactly.Quote:
Originally Posted by phsinc1
But this is what I looked at (??) Easy Tune 6 Clicked Advanced under the Tuner option, then Voltage 1.
Then looked up QPI/Vtt Voltage. Under 'Power On' it shows 1.53500V
Is this the value I was looking for or am I way out?
That's too much, try to manually set it to 1.335v or 1.355vQuote:
Originally Posted by MonsterDK
here is my settings for 3.82GHz
http://www.xtremesystems.org/FORUMS/...postcount=2876
"Target" are the Values currently used
Anybody?
what do you need exactly bro ? please let us see your bios setting so we can help youQuote:
Originally Posted by Godmyster
Ive started again working up the BLCK with the belowQuote:
Originally Posted by sunn
Multi.................... 14
Turbo .................... Disabled
Speed.................... 2800
CPU Multi Threading.................... Enabled
CPU Enhanced Halt (C1E).................... Enabled
C3/C6/C7 State Support.................... Disabled
CPU Thermal Monitor.................... Enabled
CPU EIST Function.................... Enabled
Virtualization Technology.................... Enabled
Bi-Directional PROCHOT.................... Enabled
QPI Link Speed*.................... 36
QPI Link Speed (MHz).................... 7200
Uncore Frequency.................... 17
Uncore Frequency (Mhz).................... 3400
Isochronous Support.................... Enabled
Base Clock (BCLK) Control.................... Enabled
BCLK Frequency (Mhz).................... 200
PCI Express Frequency (Mhz).................... 100
C.I.A.2.................... Disabled
CPU Clock Drive (mV).................... 800
PCI Express Clock Drive (mV).................... 900
CPU Clock Skew (ps).................... 0
IOH Clock Skew (ps).................... 0
Performance Enhance.................... Turbo
Extreme Memory Profile (X.M.P.).................... Profile1
System Memory Multiplier (SPD).................... 8
Memory Frequency (Mhz).................... 1600
DRAM Timing Selectable (sPD).................... Quick
CL.................... 8
tRCD.................... 8
tRP.................... 8
tRAS.................... 24
CMD.................... 1
Round Trip Latency.................... Auto
tRC.................... 41
tRFC.................... 88
tRRD.................... 6
tWR.................... 12
tWTR.................... 6
tRTP.................... 6
LoadLine Calibration.................... Disabled
CPU Vcore.................... 1.26875
With vdroop.................... 1.2
QPI/VTT Voltage.................... 1.315
CPU PLL.................... 1.8
PCIE.................... 1.5
QPI PLL.................... 1.1
IOH Core.................... 1.1
ICH I/O.................... 1.5
ICH Core.................... 1.1
DRAM Voltage.................... 1.64
But when raise the multi to the dizzy heights of 15 (3GHz) it will just lock up, ive tried uping each voltage one by one but it still lock in the first 17s of LinX.
????????
Your UNCORE frequency should be double your RAM speed (3200 whereas your is 3400), this might be a problem !?
any chance of speeding up the boot up time on jmicron raid for the ex58 extreme? i was able to borrow my old msi eclipse and did try to setup the HW raid on both eclipse and extreme and i clocked that the eclipse is around 3-5 secs faster than the extreme :( Also I attached the silent pipe and my IOH cooling is pretty good but i am not happy with the build in sound of the giga board so i am planning to buy xfi platinum pcie. I can put that in the last x16 slot ( configure as x8 ) right ? or is there another driver aside from realtek ( of there are any 3rd party driver that works with vista 64 please ) that can improve the sound quality of this board ( well to save some cost on my part ).
my setup
ex58 extreme - f8b
i7 920 cooled by hr01+
g skill 3 x 2 gig ddr3 1600 8-8-8-21 1.6v
MSI gtx275
2 x 74gb WD raptor 10k rpm 16mb cache -- raid 0 via HW raid
1 tb + 640 gb WD black for data and games :)
700W PSU
What bios settings do you want exactly?Quote:
Originally Posted by hlonipha
Thanks for your response
Prime95 'ing the rig and getting lock ups and reboots after about 10 mins of Torture testing....
Hardware
UD5
Intel Core i7 920 D0 Stepping (SLBEJ) 2.66Ghz (Socket LGA1366)
OCZ Gold 6GB (3x2GB) DDR3 PC3-12800C8 (1600MHz) Tri-Channel
- 1600MHz DDR3
- CL 8-8-8-24 (CAS-TRCD-TRP-TRAS)
- 1.65 Volts
Water Cooled on a Quad Rad (temps don't go above 60)
CPU Clock: 20 x
Uncore: x 16 (3200) (tried 3400)
BLCK: 200
RAM:
8
8
8
24
1
Load Line: Enabled
CPU VCore: 1.3V
QPI/Vtt: 1.335V (also tried AUTO)
Dram Volt: 1.64V
Any suggestions please?
anyone know what "Round Trip Latency" exactly do?
mine are Auto set to /55/57/60
Can I tweak them?
try to change "CPU Clock Skew" 900mV and "PCI Express Clock Skew" to 800mV, you can find them in advanced voltage controlQuote:
Originally Posted by MonsterDK
I went with the rule that its double or double +1, but no difference, still locksQuote:
Originally Posted by Jonny Manc
With a jump of vcore and vtt i could do 3GHz :rofl: surly i cant have the worst D0?
guys, running a D0 @ 4GHz with 1.28v is considered good?
Thanks for your reply,,,, but hmm,Quote:
Originally Posted by boldenc
I can't find them at all in the Advanced Voltage Control.
In advanced Clock Control I have...
CPU Clock Drive 900mV
PCI Express Clock Drive: 900mV
CPU Clock Skew: 0ps (nothing as mV)
IOH Clock Skew: 0ps (nothing as mV)
Yes, it is the "CPU Clock Drive" . "PCI Express Clock Drive", are yours defaulted to 900mV? mine was 800mVQuote:
Originally Posted by MonsterDK
Updated version:
EasyTune 6 B09.0421.1
boldenc,Lower is better, and you may freely tweak it.Quote:
Originally Posted by tweakers.fr
The worst C0 too.Quote:
Originally Posted by sunn
Any word on how to get that modded BIOS F8x flashed?
Is it just me or is ET6 a no-no on Windows 7!?
It installs ok, and the GUI process is running but I see nothing after clicking.
Tried a variety of compatability options and still nothing.......HELP!!
Exactly the same thing here Jonny.. tried to fix it without luck so far.Quote:
Originally Posted by Jonny Manc
Hows the stability going??Quote:
Originally Posted by MonsterDK