dumb question but Is that after setting RAID up in Matrix manager and Winxp install F6 or VISTA load of RAID drivers during install of operating system.Quote:
Originally Posted by nicepun
dumb question but Is that after setting RAID up in Matrix manager and Winxp install F6 or VISTA load of RAID drivers during install of operating system.Quote:
Originally Posted by nicepun
been awhile since I droped in here (i dont post much lol), but ive come away from this thread with some ideas about how to push some more outa my P5K prem.
All in all, its been a awesome board. I had the P5B D, then P5K D in different computers and even tho its only small steps, this board is diffinately the best.
Running just over 4Ghz quite easily. 35c idle / 50c load. My other setups both ran 3.4ghz 24/7, but this ones looking like 4GHZ+ 24/7.
I have seen alot of asus bashing resently, vista and intel have really put some pressure on the MB makers. good job asus, this is a quality board :)
Do you need the two little fans if your water cooling?
I put them on as they are not particularly noisey and it helps with the mosfet cooling!:DQuote:
Originally Posted by foodfightr
No dumb question at all. But your raid bios (you know know when you're able to see the HDDs on the intel RAID where you can set up different types of RAID like 1, 0, 5, 10, etc) the HDDs appear and then disappear and YES I tried it with different SATA cables.Quote:
Originally Posted by sesdave
Just got a p5k premium with my e6850.. However i cannot overclock.
During startup it starts with:
CPU fan error (cause i'm using water)
Then it says: New cpu bla bla bla. Please setup bios.
Every single time it says new cpu, i'm using bios 0404 (came with the board).
Standard clock reported 3.00 ghz, whenever i clock(no matter what speed, voltage, timings, ram etc. etc.) it display 3.01 ghz.
I've tried to reset bios using the cmos jumper, hard for me to get to the battery, it did say cmos cleared however.
HELP
Disable the CPU fan detection in the bios mate, that will get rid off that error message or hook up a case fan or such to the CPU fan connector... it might be that it just boots at stock again due to that malfunction the baords detects...
Don't worry about the 3.01ghz see it as a gift from Asus as their 333FSB prolly is 334 or such in reality
How do i disable that? Can't seem to find it anywhere..
And is there a way for me to go to bios 0402? It seems as the best for overclocking
One more thing, i had a maximus before.. The asus probe thingy showed alot more info(all voltages etc.) is it possbile to get this displayed for the p5k premium ?
Still no luck. Disabled the fan, downgraded to bios 0402.
Every single time i reboot no matter what i change it says: New CPU installed go to setup bla bla bla.
I can skip this and load default settings..
Sometimes this happens when the system is unstable. Try go stock everything and then go slowly. Also, make sure you set it to "Halt no errors" or something similar. If you don't know where certain stuff is, go READ THE MANUAL!
Situman it does this with everything standard.. Even when i just reboot from windows it says new cpu installed.
I gotta be honest, I've been lucky enough to get my hands on a sorted one of these boards.
I had 2 dodgy maximus's and no good.
Wait for it, wait for it...
just to rub it in, I run PRIME stable at 4.1ghz on my Q6600! and run my memory at 1388 at 4-4-4-8 timings.
Memory is a new batch of the OCZ flex 9200 memory...
watercooled the whole rig from mosfets to chipsets to gpu to memory.
loving it!
now this pc stays closed period. no upgrading this mother, will sell her on when its time to upgrade next xmas.
Quote:
Originally Posted by SXS
Any screenshots of this ?
be generous - its nearly christmas-lol!Quote:
Originally Posted by Devious
+2 694Mhz CL4 on the Mem I'm dying to see.Quote:
Originally Posted by Devious
[QUOTE=dikki;2627511]Situman it does this with everything standard.. Even when i just reboot from windows it says new cpu installed.[/QUOT
Update to the newest bios and see what happens. If it doesnt fix it, u need a new board.
[QUOTE=situman;2629028]Good advice - reflash using ezflash and a USB stick. Before you do that though I would check the CPU seating- You may not be getting proper contact. You may have inadvertantly got some paste on the contacts. I remebered reading this thread http://www.techsupportforum.com/hard...y-boot-up.html were the person encountered the same problem and it turned out to be a bent pin on his AMD setup. Clean you CPU contacts with some CPU cleaner and reseat. Check the MB contacts.Quote:
Originally Posted by dikki
For reading temp sensor etc and diplaying on screen try PCWIZARD 2008. http://www.cpuid.com/pcwizard.php Neat little tool and displays on screen when you minimise it.
New BIOS available - 0504
ftp://ftp.asus.com.tw/pub/ASUS/mb/so...m/P5KP0504.zip
Not tested myself yet :)
Will the P5K P bios work on P5K vanilla ?
I doubt it.
I just got this board and my PC now refuses to boot. No post, no beeps.....nothing on screen. Did you guys encounter this on your first boot up?
I have a Q6700, and 2 x X1900 XT/XTX, 150GB Raptor. CPU cooled by Mach 2 GT.
Help......
Make sure that you have the TWO 4 pin power connectors connected at top left of board (you will have to remove a cover on one of them). Your PSU will have to be good also ;)Quote:
Originally Posted by kcnyc
Anything to report on the new bios? Has anybody flashed to it yet?
Thanks for the advice, just found out my OPB Edition DDRs died......got to go find OPB for an RMA.Quote:
Originally Posted by scaramonga