Guide Thread

Printable View

Show 100 post(s) from this thread on one page

03-05-2009, 08:43 PM
radaja

the real7,hey try this for 450x9.set vcore to 1.381 in bios leave special add on auto.if it boots and you can run prime95 for at least 15 minutes then try lowering vcore.if it just primes for a few min,then try adjusting the gtl's one at a time and write down how much longer it primes until you find what your board and cpu like.this is just a starting point.let me know how it goes
CPU VID Control........................... - 1.381
CPU VID Special Add....................... - Auto
DRAM Voltage Control...................... - 2.07V
SB 1.05V Voltage.......................... - 1.15V
SB Core/CPU PLL Voltage................... - 1.55V
NB Core Voltage........................... - 1.57V
CPU VTT Voltage........................... - 1.36V
Vcore Droop Control....................... - Enabled-keep this enabled
Clockgen Voltage Control.................. - 3.45V
GTL+ Buffers Strenght..................... - Strong
Host Slew Rate............................ - Weak
GTL REF Voltage Control................... - Enabled
CPU GTL 1/3 REF Volt..................... - 110
CPU GTL 0/2 REF Volt..................... - 112
North Bridge GTL REF Volt................. - 108
also make sure you cool your nb with a fan to keep the temps down.
03-06-2009, 04:24 AM
simone18

Quote:

thanks for the bios settings at i4memory.

you're welcome ;)
anyway to push high fsb i'd give 1.75 pll and 1.40 vtt ;)
just a try, dunno if could work, but voltages are not risky
03-06-2009, 06:22 AM
radaja

thanks will give it a go
03-06-2009, 08:14 AM
eva2000
Well it's been around >1yr since I packed away my DFI UT P35-T2R. But now I have dusted it off, flashed to 09/19/08 bios and plucked in my first of five E8600 Q820A599 cpus with 0537 serial number. Too lazy to do fresh WinXP install, so grabbed my DFI DK X48-T2RSB Plus WinXP install SATA drive and just used that :)

Haven't tried 32M stability, but started off with max FSB testing for 1M and cpuz validation. Ended up around 585FSB easy 1M, 590FSB finished but BSOD before I could save screenshot and 606FSB was best I could do for validation.

Using DFI MegaHalem air heatsink with 120x25mm Thermaltake 81cfm fan and Corsair AIRFLOW assisted PWM cooling :D

http://nx.i4memory.com/reviewimages/..._megahalem.jpg

http://fileshosts.com/intel/DFI/DFI_...m_11s281ms.png

http://valid.canardpc.com/cache/banner/521499.png

http://fileshosts.com/intel/DFI/DFI_...cpuz_valid.png

System
- Intel Core 2 Duo E8600 Q820A599 0537
- DFI MegaHalem Heatsink + 120x25mm Thermaltake 81cfm fan
- DFI LP UT P35-T2R 9/19/08 bios
- 128MB Gainward FX5200 PCI
- 2GB Crucial Ballistix PC2-8500 in Green dimm slots
- 1TB Samsung SATAII
- Pioneer 216 DVD-Burner
- Corsair HX1000
- WinXP Pro SP2 (old DFI DK X48-T2RSB Plus OS drive)
Bios settings used

Code:

CPU Feature - Thermal Management Control: Disabled - PPM(EIST) Mode: Disabled - Limit CPUID MaxVal: Disabled - CIE Function: Disabled - Execute Disable Bit: Disabled - Virtualization Technology: Disabled - Core Multi-Processing: Enabled Exist Setup Shutdown: Mode 2 CLOCK VC0 divider: AUTO CPU Clock Ratio Unlock: Enabled CPU Clock Ratio: 7x CPU N/2 Ratio: Disabled - Target CPU Clock: CPU Clock: 570 boot setFSB up Boot Up Clock: AUTO DRAM Speed: 333/667 - Target DRAM Speed: 1140 PCIE Clock: 109mhz Voltage Settings CPU VID Control: AUTO CPU VID Special Add: 104.27% DRAM Voltage Control: 2.27v SB 1.05V Voltage: 1.217v SB Core/CPU PLL Voltage: 1.5v NB Core Voltage: 1.65-1.70-1.74v CPU VTT Voltage: 1.41-1.42v Vcore Droop Control: Enabled Clockgen Voltage Control: 3.45v GTL+ Buffers Strength: Strong Host Slew Rate: Weak GTL REF Voltage Control: Enabled x CPU GTL1/3 REF Volt: 74 x CPU GTL 0/2 REF Volt: 74 x North Bridge GTL REF Volt: 75 DRAM Timing - Enhance Data transmitting: AUTO - Enhance Addressing: AUTO - T2 Dispatch: Disabled Clock Setting Fine Delay Tfine Item Value Degree: 70ps (10ps to 160ps range) Ch1 Clock Crossing Setting: AUTO - DIMM 1 CLK fine delay: Current - DIMM 2 CLK fine delay: Current - Ch 1 Command fine delay: Current - Ch 1 Control fine delay: Curent Ch2 Clock Crossing Setting: AUTO - DIMM 3 CLK fine delay: Current - DIMM 4 CLK fine delay: Current - Ch 2 Command fine delay: Current - Ch 2 Control fine delay: Curent Ch1Ch2 CommonClock Setting: Auto Ch1 RDCAS GNT-Chip Delay: Auto Ch1 WRCAS GNT-Chip Delay: Auto Ch1 Command to CS Delay: Auto Ch2 RDCAS GNT-Chip Delay: Auto Ch2 WRCAS GNT-Chip Delay: Auto Ch2 Command to CS Delay: Auto (where cpuz sees 1T or 2T SETTING) CAS Latency Time (tCL): 5 RAS# to CAS# Delay (tRCD): 5 RAS# Precharge (tRP): 5 Precharge Delay (tRAS): 15 All Precharge to Act: AUTO REF to ACT Delay (tRFC): 48 Performance LVL (Read Delay) (tRD): AUTO Read delay phase adjust: Enter - Channel 1 Phase 0 Pull-In: Auto (each Phase when enabled = (Common tRD - 1) - Channel 1 Phase 1 Pull-In: Auto - Channel 1 Phase 2 Pull-In: Auto - Channel 1 Phase 3 Pull-In: Auto - Channel 1 Phase 4 Pull-In: Auto - Channel 2 Phase 0 Pull-In: Auto - Channel 2 Phase 1 Pull-In: Auto - Channel 2 Phase 2 Pull-In: Auto - Channel 2 Phase 3 Pull-In: Auto - Channel 2 Phase 4 Pull-In: Auto MCH ODT Latency: AUTO Write to PRE Delay (tWR): AUTO Rank Write to Read (tWTR): AUTO ACT to ACT Delay (tRRD): 5 Read to Write Delay (tRDWR): AUTO Ranks Write to Write (tWRWR): AUTO Ranks Read to Read (tRDRD): AUTO Ranks Write to Read (tWRRD): AUTO Read CAS# Precharge (tRTP): AUTO ALL PRE to Refresh: AUTO PCIE Slot Config: 1X 1X CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled SATA Spread Spectrum: Disabled
03-06-2009, 08:30 AM
Shiranui Gen-An

So nice to see this old board still getting attention, and with the price drops on it (in the US at least) it's a great buy. I just wish I could get it stable@500x8 5:6 PL7 on my 24/7 box :(
03-06-2009, 08:36 AM
radaja

eva2000,its great to see you've brought you UT-P35 out of retirement.thanks for the bios settings.im curious as to how setfsb works?i have downloaded it and have the right clockgen code(i think)but not sure how it works.maybe you could post some steps? thanks
03-06-2009, 12:21 PM
zsamz_

Quote:

Originally Posted by Shiranui Gen-An

So nice to see this old board still getting attention, and with the price drops on it (in the US at least) it's a great buy. I just wish I could get it stable@500x8 5:6 PL7 on my 24/7 box :(

pl7 is nothin
i got mine @500x9 almost pl6
03-07-2009, 02:02 AM
carajean

Ok im not a noob but noob to my board with a Q6600 in it. I have overclocked my E7200@3.8ghz prime, occt, and orthos stable. I am totally lost with this quad. I want to take it to 3.6ghz or higher if possible. I will be cooling with the tuniq tower.

Any help would be aprreciated. I just looking for maybe some voltage or bios setting just to get me started. Whether or not too enable Vdroop or the what other cpu options in bios to enable.
03-07-2009, 02:33 AM
J0kke

I think this is my last post to this thread. I'm losing my nerves and thinking to throw entire rig out of the window. Did a fresh install on 64bit Vista Ultimate and still I am unstable with 1:1 divider. With 2:3 divider my memory can run memtest as long as I can wait. With 500fsb and 1:1 divider only couple % and I see errors. Here is my bios template. I'd be forever thankful if someone could find a solution for my problem.

Genie BIOS Setting:

Exit Setup shutdown....................... - Mode 2
CLOCK VCO divider......................... - Auto
CPU Clock Ratio........................... - 8 X
CPU-N2 Ratio.............................. - Disabled
- Target CPU Clock........................ - 5000 MHz
CPU Clock................................. - 500 MHz
Boot Up Clock............................. - Auto
DRAM Speed................................ - 333/667
- Target DRAM Speed....................... - DDR2 1001
PCIE Clock................................ - 100 MHz
PCIE Slot Config.......................... - 1X 1X

CPU Spread Spectrum....................... - Disabled
PCIE Spread Spectrum...................... - Disabled
SATA Spread Spectrum...................... - Disabled

CPU Feature:

Thermal Management Control................ - Enabled
PPM(EIST) Mode............................ - Enabled
Limit CPUID MaxVal........................ - Disabled
C1E Function.............................. - Auto
Execute Disable Bit....................... - Enabled
Virtualization Technology................. - Enabled
Core Multi-Processing..................... - Enabled

Voltage Setting:

CPU VID Control........................... - Auto
CPU VID Special Add....................... - 112.28%
DRAM Voltage Control...................... - 2.05V
SB 1.05V Voltage.......................... - 1.15V
SB Core/CPU PLL Voltage................... - 1.55V
NB Core Voltage........................... - 1.53V
CPU VTT Voltage........................... - 1.260V
Vcore Droop Control....................... - Enabled
Clockgen Voltage Control.................. - 3.45V
GTL+ Buffers Strenght..................... - Strong
Host Slew Rate............................ - Weak
GTL REF Voltage Control................... - Enabled
CPU GTL 1/3 REF Volt..................... - 58
CPU GTL 0/2 REF Volt..................... - 60
North Bridge GTL REF Volt................. - 64

DRAM Timing:

Enhance Data transmitting................. - Fast
Enhance Addressing........................ - Fast
T2 Dispatch............................... - Auto

CAS Latency Time (tCL).................... - 5
RAS# to CAS# Delay (tRCD)................. - 5
RAS# Precharge (tRP)...................... - 5
Precharge delay (tRAS).................... - 15
All Precharge to ACT...................... - 5
REF to ACT Delay (tRFC)................... - 54
Preformance LVL (Read delay).............. - 9

MCH ODT Latencey.......................... - 4
Write to PRE Delay (tWR).................. - 12
Rank Write to Read (tWTR)................. - 12
ACT to ACT Delay (tRRD)................... - 4
Read to Write Delay (tRDWR)............... - 8
Ranks Write to Write (tWRWR).............. - AUTO
Ranks Read to Read (tRDRD)................ - AUTO
Ranks Write to Read (tWRRD)............... - AUTO
Read CAS# Precharge (tRTP)................ - 4
All PRE to Refresh........................ - 4

Clock Setting Fine Delay:

Ch1 Clock Crossing Setting................ - More Aggressive
DIMM 1 Clock fine delay................... - Current[89]
DIMM 2 Clock fine delay................... - Current[489]
Ch1 Command fine delay.................... - Current[801]
Ch1 Control fine delay.................... - Current[545]

Ch2 Clock Crossing Setting................ - More Aggressive
DIMM 3 Clock fine delay................... - Current[89]
DIMM 4 Clock fine delay................... - Current[545]
Ch2 Command fine delay.................... - Current[801]
Ch2 Control fine delay.................... - Current[489]

Ch1Ch2 CommonClock Setting................ - More Aggressive

Ch1 RDCAS GNT-Chip Delay.................. - Auto
Ch1 WRCAS GNT-Chip Delay.................. - Auto
Ch1 Command to CS Delay................... - Auto

Ch2 RDCAS GNT-Chip Delay.................. - Auto
Ch2 WRCAS GNT-Chip Delay.................. - Auto
Ch2 Command to CS Delay................... - Auto

Read delay phase adjust:

Channel 1 Phase 0 Pull-In................. - Enabled
Channel 1 Phase 1 Pull-In................. - Enabled
Channel 1 Phase 2 Pull-In................. - Enabled
Channel 1 Phase 3 Pull-In................. - Enabled
Channel 1 Phase 4 Pull-In................. - Enabled

Channel 2 Phase 0 Pull-In................. - Enabled
Channel 2 Phase 1 Pull-In................. - Enabled
Channel 2 Phase 2 Pull-In................. - Enabled
Channel 2 Phase 3 Pull-In................. - Enabled
Channel 2 Phase 4 Pull-In................. - Enabled

I have tried as high as 1.65V for NB and it only slightly makes it more stable. Im out of ideas, but as this problem has been with me quite long and I've had time to think it. Could it be the NB as the memory controller is there and it doesn't want to run my memory with 1:1 divider and with 2:3 it works great. Should I change mobo to something else because my goal was to get my E8200 @ 4ghz 24/7 and with this board I cant do it. ANY ADVICE AND HELPING WILL BE GREATLY APPRECIATED! I HAVE FAITH IN YOU PROS!!!!
03-07-2009, 02:39 AM
simone18

Quote:

Originally Posted by zsamz_

pl7 is nothin
i got mine @500x9 almost pl6

quote. when i started to clock towards 600fsb pl6 could work over 500fsb. then i went pl7 and pl8 over 580-590 ;)
03-07-2009, 09:57 AM
radaja

yep at 540fsb for me i could use pl7 with e/a/e/e/e and e/a/a/e/e but one i went to 542 i had trouble with stability but once i went to pl8 with the same pull ins it was better
03-07-2009, 12:42 PM
lucasweir

hey everyone i currently have a E6300 at 3ghz 7X430

heres some screenies

http://img.techpowerup.org/090307/Capture.jpg

any advice how to maximize my overclock/make more efficent
03-07-2009, 01:12 PM
zsamz_

Quote:

Originally Posted by simone18

you're welcome ;)
anyway to push high fsb i'd give 1.75 pll and 1.40 vtt ;)
just a try, dunno if could work, but voltages are not risky

you wrong i already degraded my e685o with 1.65pll
vtt volts not risky but pll volts above 1.7v is

lucas dont be scared to go 500x7 you should be able to do it under 1.45v
i got my e6400 to 3.9 easy
03-07-2009, 03:01 PM
the9093

Quote:

Originally Posted by lucasweir

hey everyone i currently have a E6300 at 3ghz 7X430

i too have a e6300 and running @ 480x7=3360MHz

CPU=1.33125v
RAM= in my sig
cpu vtt=1.28v
NB=1.45v

try those volts and see how you do. i have to warn you with my advice, i'm no pro when it comes to OCing.
03-07-2009, 03:14 PM
Shiranui Gen-An

Some E6300s won't hit 500FSB, I know mine won't no matter what board I slap it in. 490 is about its wall.
03-09-2009, 02:15 AM
lucasweir

i tried 500X7 that didnt even boot at 1.46V with NB core at 1.50V and 1.43 cpu Vtt

any other sugestions?

my chipset and VRM are around 30 C if thats good with my current overclock from above
03-09-2009, 04:40 AM
simone18

Quote:

you wrong i already degraded my e685o with 1.65pll

strange...a made lots of try with e8400 + 1,75v PLL and no problem...my cpu still rock hard reaching 655mhz fsb @ air on giga ud3r :D
03-09-2009, 07:45 AM
J0kke

Quote:

Originally Posted by J0kke

I think this is my last post to this thread. I'm losing my nerves and thinking to throw entire rig out of the window. Did a fresh install on 64bit Vista Ultimate and still I am unstable with 1:1 divider. With 2:3 divider my memory can run memtest as long as I can wait. With 500fsb and 1:1 divider only couple % and I see errors. Here is my bios template. I'd be forever thankful if someone could find a solution for my problem.

Genie BIOS Setting:

Exit Setup shutdown....................... - Mode 2
CLOCK VCO divider......................... - Auto
CPU Clock Ratio........................... - 8 X
CPU-N2 Ratio.............................. - Disabled
- Target CPU Clock........................ - 4000 MHz
CPU Clock................................. - 500 MHz
Boot Up Clock............................. - Auto
DRAM Speed................................ - 333/667
- Target DRAM Speed....................... - DDR2 1001
PCIE Clock................................ - 100 MHz
PCIE Slot Config.......................... - 1X 1X

CPU Spread Spectrum....................... - Disabled
PCIE Spread Spectrum...................... - Disabled
SATA Spread Spectrum...................... - Disabled

CPU Feature:

Thermal Management Control................ - Enabled
PPM(EIST) Mode............................ - Enabled
Limit CPUID MaxVal........................ - Disabled
C1E Function.............................. - Auto
Execute Disable Bit....................... - Enabled
Virtualization Technology................. - Enabled
Core Multi-Processing..................... - Enabled

Voltage Setting:

CPU VID Control........................... - Auto
CPU VID Special Add....................... - 112.51%
DRAM Voltage Control...................... - 2.1V
SB 1.05V Voltage.......................... - 1.15V
SB Core/CPU PLL Voltage................... - 1.55V
NB Core Voltage........................... - 1.53V
CPU VTT Voltage........................... - 1.150V
Vcore Droop Control....................... - Enabled
Clockgen Voltage Control.................. - 3.60V
GTL+ Buffers Strenght..................... - Strong
Host Slew Rate............................ - Weak
GTL REF Voltage Control................... - Enabled
CPU GTL 1/3 REF Volt..................... - 68
CPU GTL 0/2 REF Volt..................... - 67
North Bridge GTL REF Volt................. - 67

DRAM Timing:

Enhance Data transmitting................. - Auto
Enhance Addressing........................ - Auto
T2 Dispatch............................... - Auto

CAS Latency Time (tCL).................... - Auto
RAS# to CAS# Delay (tRCD)................. - Auto
RAS# Precharge (tRP)...................... - Auto
Precharge delay (tRAS).................... - Auto
All Precharge to ACT...................... - Auto
REF to ACT Delay (tRFC)................... - Auto
Preformance LVL (Read delay).............. - 10

MCH ODT Latencey.......................... - Auto
Write to PRE Delay (tWR).................. - Auto
Rank Write to Read (tWTR)................. - Auto
ACT to ACT Delay (tRRD)................... - Auto
Read to Write Delay (tRDWR)............... - Auto
Ranks Write to Write (tWRWR).............. - AUTO
Ranks Read to Read (tRDRD)................ - AUTO
Ranks Write to Read (tWRRD)............... - AUTO
Read CAS# Precharge (tRTP)................ - Auto
All PRE to Refresh........................ - Auto

Clock Setting Fine Delay:

Ch1 Clock Crossing Setting................ - Auto
DIMM 1 Clock fine delay................... - Current[89]
DIMM 2 Clock fine delay................... - Current[489]
Ch1 Command fine delay.................... - Current[801]
Ch1 Control fine delay.................... - Current[545]

Ch2 Clock Crossing Setting................ - Auto
DIMM 3 Clock fine delay................... - Current[89]
DIMM 4 Clock fine delay................... - Current[545]
Ch2 Command fine delay.................... - Current[801]
Ch2 Control fine delay.................... - Current[489]

Ch1Ch2 CommonClock Setting................ - Auto

Ch1 RDCAS GNT-Chip Delay.................. - Auto
Ch1 WRCAS GNT-Chip Delay.................. - Auto
Ch1 Command to CS Delay................... - Auto

Ch2 RDCAS GNT-Chip Delay.................. - Auto
Ch2 WRCAS GNT-Chip Delay.................. - Auto
Ch2 Command to CS Delay................... - Auto

Read delay phase adjust:

Channel 1 Phase 0 Pull-In................. - Enabled
Channel 1 Phase 1 Pull-In................. - Enabled
Channel 1 Phase 2 Pull-In................. - Enabled
Channel 1 Phase 3 Pull-In................. - Enabled
Channel 1 Phase 4 Pull-In................. - Enabled

Channel 2 Phase 0 Pull-In................. - Enabled
Channel 2 Phase 1 Pull-In................. - Enabled
Channel 2 Phase 2 Pull-In................. - Enabled
Channel 2 Phase 3 Pull-In................. - Enabled
Channel 2 Phase 4 Pull-In................. - Enabled

I have tried as high as 1.65V for NB and it only slightly makes it more stable. Im out of ideas, but as this problem has been with me quite long and I've had time to think it. Could it be the NB as the memory controller is there and it doesn't want to run my memory with 1:1 divider and with 2:3 it works great. Should I change mobo to something else because my goal was to get my E8200 @ 4ghz 24/7 and with this board I cant do it. ANY ADVICE AND HELPING WILL BE GREATLY APPRECIATED! I HAVE FAITH IN YOU PROS!!!!

I did some changes to my template, suggested on DFI forums. Still im not able to get this stable.... Why is it with 2:3 divider Performance level 5 on auto and with 1:1 it is 9 on auto? Also memset shows difference in tREF with 2:3 it is 3120 and with 1:1 it is 2500. Thanks!
03-09-2009, 10:27 AM
lucasweir

try turning off all cpu features off except for multi-processing
03-09-2009, 10:52 AM
zsamz_

yup lucas is right
you cant overclock with all them options enabled

Thermal Management Control................ - Enabled "dissable"
PPM(EIST) Mode............................ - Enabled "dissable"
Limit CPUID MaxVal........................ - Disabled
C1E Function.............................. - Auto "dissable" you can enable for slight overclock
Execute Disable Bit....................... - Enabled
Virtualization Technology................. - Enabled "dissable" verry important to dissable
Core Multi-Processing..................... - Enabled
03-09-2009, 10:53 AM
zsamz_

Quote:

Originally Posted by simone18

strange...a made lots of try with e8400 + 1,75v PLL and no problem...my cpu still rock hard reaching 655mhz fsb @ air on giga ud3r :D

for a short time ok
if you feel lucky keep it there:rofl:
03-10-2009, 04:58 AM
simone18

obviously i keep it only thetime necessary to boot, s-pi 1m ;)
03-11-2009, 09:47 AM
radaja

hey if anyone is interested im thinking of selling my DFI UT-P35-T2R that i bought three weeks ago.its in perfect condition,i only used for two weeks, none of the accessories were ever used(still sealed in original packaging).im trying to get some money together to buy another 9650.let me know if your interested
03-11-2009, 11:36 AM
zsamz_

radaja i suggest u keep it as a backup
those gigabut boards not reliable in my book
03-11-2009, 09:36 PM
patrickadizzle

Anyone here ever gotten post code 88?

I can't seem to get out of it, I did a 6 hour CMOS clear and still nothing.

Thanks

Show 100 post(s) from this thread on one page

**Official DFI LanParty UT P35-T2R Review/Overclock/Guide Thread**

Official DFI LanParty UT P35-T2R Review/Overclock/Guide Thread