I currently have my monitor set at 2560 x 1600 resolution. I set the bios to it's defaults and I installed another set of memory for a total 4x2GB. I booted into windows and the monitor resolution reset to the default; 800 x 600. Under 'Display Settings' the maximum resolution I could now set was 1920 x 1440. I have dual monitors, but the problem occurs with just one monitor also.
Does anyone have a solution/reason....Thanks
Hi, I just recently purchased the UT and have been looking through this thread and it seems to be a mixed bag of results regarding the transpiper, copper plate, and location to mount it (if mounted at all). Anandtech seems to suggest that it has a negative effect on cooling the CPU and suggest that it be mounted on the southbridge if one chooses to mount it. But it seems that there are a few out there that have had success with it. Is there a concensus to what is the better method?
Please let me know,
Thanks :)
(btw, this will be in an Antec 900 so the PSU is actually at the bottom of the case)
you dont need that copper plate it will tranfer heat to the pwmQuote:
Originally Posted by mk_ln
and a fan will cool the pwm alot better then the trandspiper
i removed all the original heatsinks n heapipes but lost warranty:eek:
you might wanna put the transpiper on the sb m put a fan on the pwm heatsink as you have a quad
I have this same board and I have been wondering if I can get a Q6600 up to 4.0ghz on air with this board????????????????
this is on aircooling :DQuote:
Originally Posted by carajean
http://img530.imageshack.us/img530/6...mark06est5.jpg
Quote:
Originally Posted by DJSUB
Hey I need to know what kind of air cooling and what ram ur using. PLEASE!!!
That's pretty darn impressive!!!
I installed a hardware RAID card and (I think) updated to the newest BIOS at the same time. Since then if I try to use 2 dimms windows doesn't load the graphics driver. I haven't experimented with it too much but I did quickly try bumping up the NB and RAM volts to no avail.Quote:
Originally Posted by doakh
What BIOS are you using? Any RAID card?
Saint-Francis.....
Yes I did. I installed ATI CAT 8.1 (driver only) from about a year ago, based on crusing the web and low and behold it works with 8GB and 2560 x 1600 resolution! I had tried several drivers ...8.6, 8.9, 8.11, and 8.12 with no luck, so I wonder what changed in subsequent updates?
I deleted the driver and rebooted in Safemode and used 'Drive Cleaner' to remove anything left over (about ten files).
I have not tried to install CCC 8.1. I stopped here after it worked. I was tired of messing around. May be CAT 8.12 (driver only) would work after using 'Drive Cleaner' in Safe Mode.
1.73 VCore on air cooling?Quote:
Originally Posted by DJSUB
Can you show us your Core temp too please? :)
Same MB and CPU here but 4GHz is very difficult (I don't want that insane voltage for a daily use :D )
i think another factor would be DJSUB's chip...i think it's a good batchQuote:
Originally Posted by Eisenheim
In my case I think that I have to give up and keep a 3.6 GHz @ 1.4000V for the daily use...
why my E8400 so hot in this board but not in DK P35 T2RS?....
i sett de clock at 4ghz (multi 9) n vcore at 1,255v.......
idle at 50c but when i test orthos only 78c.....
can somebody tell me the solution?....
System:
Intel C2D E8200
DFI UT P35 T2R
G-Skill PI PC2-8000 1000mhz 5-5-5-15
GTX 260
Mushkin EP-500ap
2 Samsung sata HDDs
Sata S-223hf dvd
Xigmatek HDT-1283s
Problem is I can't get my system stable @ 8x500 mem is at 1:1 and at their specsed settings. Memtest gives errors. when I set everything default it seems to run fine. Vcore 1.34, Vmem 2.1v, Vnb 1.57v VTT 1.310v VTT default and I dont now what to do. Please help I'm using the latest bios. Should I downgrade it? I think the older one worked better. My board has killed one Crucial BallistiX set and I got one A-Data 800mhz cl4 kit and it DOA. Then I bought this G-Skill set and at the beginning it worked out good. Thanks for replies.
E: Did more research and found out that 1:1 divider is making me crazy, at 2:3 divider @ same settings no errors in memtest. Any Ideas? Should I change bios?
E2: What do you think is the best bios for this model, at the moment I have latest.
Anyone?Quote:
Originally Posted by J0kke
copy your bios template n maybe then we can helpQuote:
Originally Posted by J0kke
remount your heatsinkQuote:
Originally Posted by AnaMan
I'm having trouble setting up three cards on my p35. It won't register the 3rd card. I ran it with gfx cards in the first and third pic-e slot and first and second slot no issues. No matter what slot third card goes in no dice. BTW I'm running xp32.
i dont know about ur mobo, but if it does really support 3 cards u could try..Quote:
Originally Posted by =[PULSAR]=
putting all the gpu's into the mobo, re-moving all power from chipset etc by clicking the power button a few times with the psu off.
then remove psu power cable, move cmos pin over to clear & take the battary out the mobo for 5mins.
after that put the batt back in & move the jumper pin back over.
if that dont work try leaving the battary out longer.
obvously its not gonna do nothing if the mobo just dont support 3 cards :shrug:
CPU FeatureQuote:
Originally Posted by zsamz_
- Thermal Management Control: Enabled
- PPM(EIST) Mode: Enabled
- Limit CPUID MaxVal: Disabled
- CIE Function: Enabled
- Execute Disable Bit: Enabled
- Virtualization Technology: Enabled
- Core Multi-Processing: Enabled
Exist Setup Shutdown: Mode 2
CLOCK VC0 divider: AUTO
CPU Clock Ratio Unlock: Enabled
CPU Clock Ratio: AUTO
- Target CPU Clock: 4000
CPU Clock: 500
Boot Up Clock: AUTO
DRAM Speed: 333/667
- Target DRAM Speed: 1001
PCIE Clock: 100mhz
Voltage Settings
CPU VID Control: AUTO
CPU VID Special Add: 111.81%
DRAM Voltage Control: 2.1
SB 1.05V Voltage: 1.050
SB Core/CPU PLL Voltage: default
NB Core Voltage: 1.57
CPU VTT Voltage: 1.310
Vcore Droop Control: Enabled
Clockgen Voltage Control: 3.60v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
GTL REF Voltage Control: Enabled
x CPU GTL1/3 REF Volt: 65
x CPU GTL 0/2 REF Volt: 67
x North Bridge GTL REF Volt: 66
DRAM Timing
- Enhance Data transmitting: AUTO
- Enhance Addressing: AUTO
- Channel 1 CLK fine delay: AUTO
- Channel 2 CLK fine delay: AUTO
CAS Latency Time (tCL): 5
RAS# to CAS# Delay (tRCD):5
RAS# Precharge (tRP):5
Precharge Delay (tRAS):15
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance Level: AUTO
MCH ODT Latency: AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO
PCIE Slot Config: 1X 1X
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled
Im using those settings. Thanks for help.
E: Tried again, no luck, BSODS etc. Memtest errors. Can't understand what makes my system so unstable. Tested memory yesterday when everything was default, and memory at its rated 5-5-5-15 2.1v 1000mhz. It ran 280% MemTest WITHOUT ERRORS. All temps are good. PSU gives good looking voltages and is quite new. Should I change my bios to older one? I remember the older was better, was it 5/21 or something like that? BTW whats the best bios for 45nm C2D overclocking?
E2: OK, bios downgraded to 521, lets see what happens this time...
^^^
Have a look at the link next to the UT-P35 in my sig. It will give you a good idea of the sort of settings you need at 500 FSB. Have a look at Memset as well to see what the Auto setting is for tRFC. More often than not the auto setting is too relaxed, and can cause Bsod's and memory errors.
Thanks mate, ill try that out and report back what happens.Quote:
Originally Posted by kitfit1
Have a look at Memset as well to see what the Auto setting is for tRFC. More often than not the auto setting is too relaxed, and can cause Bsod's and memory errors, can you explain what I need to do here, never used memset before. Thanks. Heres a photo of my memset:
http://i40.tinypic.com/1huzyh.jpg
Memset is telling you that the Auto setting for tRFC is 52, which sounds about right for a 2x2g set of ram. Only sometimes it may set it to 62, which is a bit too relaxed for a 2x2g set.
You don't need to do anything, your only using Memset to see what the auto settings are.
Ok, I set TRFC to 45 and had 3 errors in 30min memtest run. Last time when it ran couple % it had way more errors. What does this mean? You seem to know alot of this mobo, can u give any more advice of what to do? In Dram Timing sub menu all else is auto except timings which are 5-5-5-15 and TRFC 45. Thanks:clap:Quote:
Originally Posted by kitfit1
Edit: What does this TRFC affect, id like to know so could understand more than just values ;) Lowest possible tRFC Im able to boot is 43. Now its set to that and enchance settings to fast and data transmitting to more aggressive. Ill test again.
dont set trfc lower than 48Quote:
Originally Posted by J0kke
and set performance lever to 8 set pulls to eaeee eaaee set memory to more aggressive