Printable View
Another Brisbane 4000+ AM2...
Batch is CAASG ....... (forgot the last part)
Max stable on stock VCore about 2.8 GHz.
3 GHz is stable with additional voltage.
Max clock @ 1.53 V with phase change : 3440 MHz.
http://valid.x86-secret.com/show_oc.php?id=270219
DFI LP Ultra-SLI
4200+ X2 @250
G.Skill HZ F1 DDR500 3-4-4-8
One question i have is if i can boot into windows and run normal apps at 3.0Ghz (273x11) how do i make the computer stable at that number to run SP2004? i have went up to 1.55 volts but sooner or later it fails.
The answer may lie in the sub-timings of your RAM, Ultra-D is very sweet setting this with, I have one of my own :) Find out your optimal MAL, RP, DRIVE STRENGTH and DATA DRIVE STRENGTH. May be set somewhat weaker all of them, and may as a side-effect cause stability ;)Quote:
Originally Posted by on1yalad
Try one at a time, drive strength and data drive strength is important. But also setting TREF is very important, rather then leaving it at auto. Let it say auto and find out what refresh rate it's at from everest or some other software that reads it. Then check out what each TREF in bios means, and set it at the correct microsecond (us) refresh rate. This is a difficult setting on DFI boards, but nonetheless very important for getting the stability a and performance you want.
What can you say but HOLY TOLEDO! :rofl: :rofl: :rofl:Quote:
Originally Posted by Blademaster
Impressive clocks, I never got mine above 2800 on air and that thing would fry an egg for sure.
Hi Xtreme friends,
Chek my toledo:
Core: LCBQE
stepping: SPMW
week: 0721
and....my WR :D
http://www.ripping.org/database.php?cpuid=414
http://valid.x86-secret.com/show_oc.php?id=270840
max stable clock...
http://img251.imageshack.us/img251/4...2600mhzmj7.jpg
at 2670mhz it runs prime for 4 hours, at 2700mhz for 18 minutes, at 2800mhz less than a minute... all with stock vcore (1.25 - 1.30v)
ADO4000IAA5D0
NAARG0737GPMW
Boost up the vcore to 1.375~1.4v and it does 2.7 GHz easy :)Quote:
Originally Posted by Spectrobozo
It may be that the memcontroller needs just a little bit more voltage :)
2.7ghz or more?!Quote:
Originally Posted by freakBYnature
the problem is that my motherboard (asrock alivenf6g-dvi) doesn't let me to increase the vcore, only decrease :down:
there is a little modification to increase, but that will just make useless the cool n quite to (cool n quit will run with 1.3v or more), and since I let this PC downloading files for most of the time cool n quite is a good.
Look this Bios mod for your mb, http://www.box.net/shared/6bc15dlctcQuote:
Originally Posted by Spectrobozo
There is a big list with modded bios in this thread.
http://forums.mydigitallife.info/sho...p?t=3&page=312
cool & quiet aint useful when overclocking anyway, it can (and in most cases will) make your system unstable. So if you can mod it, or take up on the advice and test out an unlocked modded bios I would make the suggestion, just do it. These cpu's can handle 24/7 up to 1.45~1.5v for years in most cases, depending on your cooling :) Clock it till it rocks! ;)Quote:
Originally Posted by Spectrobozo
And yeah... 2.7 GHz is in most cases easy with these cpu's. I have still not found one that doesent do that.
Only valid at this time. Vcore limit to 1.55V ( mobo limit ), air cooling, ihs out :up:
http://valid.x86-secret.com/show_oc.php?id=273613
Martin
AMD X2 4000+
ADO4000 IAA5DD
CAAIG 0705 XPMW
Z134752B70093
2,812 GHz mit Standart vCore (1,2750 im Bios)
http://img252.imageshack.us/img252/6308/oc3wa6.jpg
my Toledo x2 4200 2.2 @ 2.4ghz is currently running around 39C in Bios
CoreTemp shows 24C Core 0 and 29C Core 2
which one to trust?
i know this thing can get up to 2.7 ghz
i have it on a dfi lanparty sli-d mobo with an arctic cooler 64 pro ... with AS5
I think Bios is correct
4600+ X2 manchester 939
Asus A8N-SLI 1014 bios
4x512 centon ddr400
EVGA 8800GT o'cd 730/1000
thermalright xp-90/92mm fan HSF
xion 600watt powereal PSU
http://<a href="http://img152.images...kyetlr6.th.png[/IMG]
I dont know how some are getting 3 ghz stable. I couldnt even boot at 2.99 and have only now been able to run prime 95 stable for 1.5 hours.
I didnt tweek ram at all... only set it to 333mhz.
How do I go about getting higher speeds?
How am I doing? : D
http://img.photobucket.com/albums/v1...cpuzcegras.png
I believe I can go higher. TRUE w/ S-Flex F, I load at just under 60 on Orthos.
I might get 2.8 on this.
"LCB9E 0633 BPMW" - not sure if it's BP or CD "revision"
I can get 2750MHz stable on my x2 3800+ and 2800 seems ok, for general usuage but my temperatures are not good - getting new h/s/f soon - probably the best I can find.
btw, cegras, thats a good clock is it on stock vcore? if it is then you should be onto a winner. Some that can do 2.7ghz on stock can do 3000 on 1.5v or so from what I have read (toledo x2s) and this one has done 3006 before on 1.55v for benchmarking and it didnt lock up at all, it just got too toasty.
cpu-z verification upto 3217MHz - ac cooling freezer pro w/ 80mm fan - and super pi at ~3050 - 1MB ~ 29s
http://valid.x86-secret.com/show_oc?id=202127
SiSoftware Sandra
Benchmark Results
Dhrystone ALU : 16109MIPS
Whetstone iSSE3 : 16568MFLOPS
Results Interpretation : Higher index values are better.
Performance vs. Speed
Dhrystone ALU : 5.86MIPS/MHz
Whetstone iSSE3 : 6.02MFLOPS/MHz
Results Interpretation : Higher index values are better.
Performance vs. Power
Processor(s) Power : 116.35W
Dhrystone ALU : 138.45MIPS/W
Whetstone iSSE3 : 142.40MFLOPS/W
Results Interpretation : Higher index values are better.
Performance Test Status
Run ID : 1x AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ (Dual-Core, 2.75GHz, 2x 512kB L2)
Platform Compliance : Win32 x86
NUMA Support : No
SMP (Multi-Processor) Benchmark : No
Total Test Threads : 2
Multi-Core Test : Yes
Cores per Processor : 2
SMT (Multi-Threaded) Benchmark : No
Processor Affinity : P0C0T0 P0C1T0
System Timer : 2.75GHz
Number of Runs : 64000 / 640
Processor
Model : 1x AMD Athlon(tm) 64 X2 Dual Core Processor 3800+
Speed : 2.75GHz
Model Number : 3800
Cores per Processor : 2 Unit(s)
Type : Dual-Core
L2 On-board Cache : 2x 512kB, ECC, Synchronous, Write-Back, 16-way, 64 byte line size
Features
SSE Technology : Yes
SSE2 Technology : Yes
SSE3 Technology : Yes
Supplemental SSE3 Technology : No
SSE4.1 Technology : No
SSE4.2 Technology : No
EMMX - Extended MMX Technology : Yes
SSE4A Technology : No
HTT - Hyper-Threading Technology : No
the above si soft sandra arithmetic benchmark was at 2806MHz - it says 2750 for a reason - because I boot the PC up at 2750 (BIOS) and set it to 2800 (Clockgen) as my mobo (EPOX 9nda) doesnt like 1t RAM CPC above 276 htt.
http://aycu29.webshots.com/image/395...1329487_rs.jpg
You do know I bought the Aerocool ExtremeEngine 3T, and with the Zalman 9700LED I got 2.8 GHz @ 1.425V instead of 2.75GHz... the temps are not even getting to 40c orthos load, and my mem is really weak when run on a divider, but I got it to DDR466 when set @ 3-4-4-10 1T... and I do know my timings aint the best, but it's UCCC for crying out loud... it's not that bad. I get DDR500 3-4-4-8 1T, but only when run 1:1 with the CPU.Quote:
Originally Posted by ben rogers
I told you that I believe you can clock your cpu more if you get a better cooler, but I also got 50mhz more without the biggest hazzle on mine only by swapping the case. The one I've mentioned was really sweet I tell you. Lots of headroom for clocking with a cool, noisefree case.
I HATE NOISE :mad:
BUT LOVE CLOCKING! :rofl:
http://valid.x86-secret.com/show_oc.php?id=300962
Just started pushing this 6400.
After work update:
http://i31.photobucket.com/albums/c3...Mcalc28967.jpg
my AMD X2 4000+ EE @ 3.44Ghz in aircooling :)
http://valid.x86-secret.com/show_oc.php?id=299719
Stable @2.9ghz vcore stock
http://images3.hiboox.com/vignettes/0308/huecfz6a.jpg
this is my x2 3800+ OC 2 2.5ghz vcore 1.400
my board is MSI k9n NEO v3
i can't go further to 2.6ghz up because my vcore is luck
http://s68.photobucket.com/albums/i1...nt=rapOCCT.jpg