Asus BD FX Support for Crosshair IV/890 boards

Printable View

Show 100 post(s) from this thread on one page

10-24-2011, 01:04 PM
zoomee

Quote:

Originally Posted by Raja@ASUS

Should have updated BIOSes for the CIVE/F by next week. HQ are workin' on it. Sorry for the delay!!

Aww man, cudda told us that earlier this week!. Oh well, i just got me a 2600k and an asrock x4 g3 yesterday to replace my chiv n thuban.

Sent from my GT-I9100 using Tapatalk
10-26-2011, 11:58 AM
eagle101

Bios question:

I have a crosshair IV Extreme.I have 0502 Bios now
im going 1100T cpu Saturday this bios 0502 should be ok right

Thanks
10-26-2011, 06:23 PM
wez

Quote:

Originally Posted by eagle101

Bios question:

I have a crosshair IV Extreme.I have 0502 Bios now
im going 1100T cpu Saturday this bios 0502 should be ok right

Thanks

Yea the 0502 is fine for the 1100t. I ran that bios most of the time on my 1090t

Got myself a 8120 now, so eagerly waiting for a update now :)
10-26-2011, 09:17 PM
eagle101

Quote:

Originally Posted by wez

Yea the 0502 is fine for the 1100t. I ran that bios most of the time on my 1090t

Got myself a 8120 now, so eagerly waiting for a update now :)

you mean the bd cpu will work with the bios update in the ch4 extreme board?
thanks for the bios check for me, had to double check
10-26-2011, 10:43 PM
FlanK3r

no....u must waiting for new BIOS.
10-27-2011, 10:15 AM
Zeus

Come on Asus, i really want to play with BD. I really hope this bios will be available before BD hit the stores here in Europe.
10-31-2011, 12:56 AM
wez

Quote:

Originally Posted by Zeus

Come on Asus, i really want to play with BD. I really hope this bios will be available before BD hit the stores here in Europe.

Seen a couple stores with the 8120 in stock starting today, so hopefully you'll get one soon :)
10-31-2011, 03:19 AM
Raja@ASUS

Enable retail stepping BD support

CIVE BIOS 3027:

http://www.mediafire.com/file/v87k8e...-ASUS-3027.zip

CIVF BIOS 3027:

http://www.mediafire.com/file/vduzeb...-ASUS-3027.zip
10-31-2011, 03:37 AM
wez

Quote:

Originally Posted by Raja@ASUS

CIVE BIOS 3027:

http://www.mediafire.com/file/v87k8e...-ASUS-3027.zip

CIVF BIOS 3027:

http://www.mediafire.com/file/vduzeb...-ASUS-3027.zip

Now this is a pleasant surprise! Didn't expect anything until the end of the week. Big thanks Raja :)

Will report my first impression later tonight
10-31-2011, 04:20 AM
erek

Quote:

Originally Posted by Raja@ASUS

CIVE BIOS 3027:

http://www.mediafire.com/file/v87k8e...-ASUS-3027.zip

CIVF BIOS 3027:

http://www.mediafire.com/file/vduzeb...-ASUS-3027.zip

will there be a M4A89GTD Pro/USB3 bios update soon?
10-31-2011, 04:30 AM
Zeus

Are those Bulldozer supporting bios' Raja?
10-31-2011, 04:48 AM
BeepBeep2

Quote:

Originally Posted by Zeus

Are those Bulldozer supporting bios' Raja?

Yes.
10-31-2011, 09:13 AM
eagle101

just to tripple check myself the CIVE BIOS 3027 Raja's saying will work with bulldoser cpu in a crosshair IV 890 chipset boards?
thanks
10-31-2011, 09:41 AM
erek

Quote:

Originally Posted by eagle101

just to tripple check myself the CIVE BIOS 3027 Raja's saying will work with bulldoser cpu in a crosshair IV 890 chipset boards?
thanks

yes
10-31-2011, 10:45 AM
wez

Works on my extreme with a 8120, need to enable/disable turbo core in AOD to get rid of the core freq jumping under load but after that it seem solid. Only played with it for a few hours, but so far so good. These things sure clock ram better than thuban on 890's as well :)
10-31-2011, 11:02 AM
Zeus

Cool!! Thanks Asus and thanks Raja.

Now the million dollar question: Does a mobo flashed with this bios still work with Thuban or Deneb cpu?
10-31-2011, 11:12 AM
The Stilt

Quote:

Originally Posted by Zeus

Now the million dollar question: Does a mobo flashed with this bios still work with Thuban or Deneb cpu?

It does, however it is now optimized for Bulldozer so K10 gear might do worse than before.
10-31-2011, 12:24 PM
wez

Be careful pushing too high, I'm not joking when I say the 8pin power connector are now fused to my board.. Primed at 4750mhz 1.45v, testing out some imc scaling when things started to smell funkeh ^^
10-31-2011, 01:16 PM
erek

Quote:

Originally Posted by wez

Be careful pushing too high, I'm not joking when I say the 8pin power connector are now fused to my board.. Primed at 4750mhz 1.45v, testing out some imc scaling when things started to smell funkeh ^^

does the setup still fire on?
10-31-2011, 01:24 PM
Zeus

Ouch! That usually happens when contact is not firm enough. Perhaps the pins in the 8 pin connector were a tiny bit too wide/loose? Priming at 4750 sounds good though! Low VID is high powerdraw and loads of heat output. What temps did you see?
10-31-2011, 01:44 PM
wez

Quote:

Originally Posted by erek

does the setup still fire on?

Yea, still runs fine :) Testing 4600mhz as we speak at ~1.36v, 80w less drawn from the wall compared to 4750/1.45v

Quote:

Originally Posted by Zeus

Ouch! That usually happens when contact is not firm enough. Perhaps the pins in the 8 pin connector were a tiny bit too wide/loose? Priming at 4750 sounds good though! Low VID is high powerdraw and loads of heat output. What temps did you see?

Connector was plugged in all the way, and now its stuck there extra good lol.
Temps where 60+, didn't pay too much attention to it
10-31-2011, 09:21 PM
eagle101

Quote:

Originally Posted by wez

Yea, still runs fine :) Testing 4600mhz as we speak at ~1.36v, 80w less drawn from the wall compared to 4750/1.45v

Connector was plugged in all the way, and now its stuck there extra good lol.
Temps where 60+, didn't pay too much attention to it

wez....your the 1st i see with the CH IV Extreme with the 8120 very cool......
do you need lots of bios adjustments to get it going or is it simple like 1100Ts and phenoms....just wondering
10-31-2011, 10:16 PM
Daveburt714

Quote:

Originally Posted by Raja@ASUS

Enable retail stepping BD support

CIVE BIOS 3027:

http://www.mediafire.com/file/v87k8e...-ASUS-3027.zip

CIVF BIOS 3027:

http://www.mediafire.com/file/vduzeb...-ASUS-3027.zip

Great Raja!.... Now I'm temped to go buy a 6100 to try in my C4F. :shakes:
Even though I have absolutely no need for one other than to play with... :ROTF:

J/K man, glad to see you guys kept your word and supplied a functioning BD bios for the older Crosshairs!

wez: Really sorry to hear about your board problems, that Sucks!
I noticed in the other thread you said your chip had a 1.25 VID and you weren't too happy with it.
I'm not suggesting you didn't go slow with v's, and it may just be that the older boards don't do real well with FX.
Reguardless, now that you're 8pin is burnt could you see how far it goes with low v's?

Thanks,
Dave
11-01-2011, 01:04 AM
wez

Quote:

Originally Posted by Daveburt714

Great Raja!.... Now I'm temped to go buy a 6100 to try in my C4F. :shakes:
Even though I have absolutely no need for one other than to play with... :ROTF:

J/K man, glad to see you guys kept your word and supplied a functioning BD bios for the older Crosshairs!

wez: Really sorry to hear about your board problems, that Sucks!
I noticed in the other thread you said your chip had a 1.25 VID and you weren't too happy with it.
I'm not suggesting you didn't go slow with v's, and it may just be that the older boards don't do real well with FX.
Reguardless, now that you're 8pin is burnt could you see how far it goes with low v's?

Thanks,
Dave

Priming at 4.75ghz 1.45v the rig pulled 600W from the socket, so no doubt these chips draw a lot oc'ed. And perhaps there are a reason the formula V got an extra 4pin power connector ^^
Working with lower volts atm. I keep pushing until it start to smell, then take it down a notch or two :D
RAM clocks much better than agena/thuban so having some fun with that, 2000 7-7-7 was a breeze, IMC doesnt clock that well, around 2700 seem to be the limit.
11-01-2011, 09:04 PM
lizardmech

Works on my crosshair IV formula. Bulldozer performance seems dismal though, at 4.6ghz my fx 8120 10-30% slower than my 3.8ghz 1100t is in multithreaded rendering programs.

Show 100 post(s) from this thread on one page