Intel Core i7 - DO NOT REMOVE IHS!

Printable View

Show 100 post(s) from this thread on one page

11-29-2008, 03:44 PM
JoeBar

We need pics of the cpu and the person who did it... :D
11-29-2008, 04:42 PM
ColonelCain

Can you show us pics please? I am really intriuged to see that first obligatory picture of Nehalem naked. :yepp:
11-29-2008, 04:43 PM
Vatos_locos

WE WANT :banana::banana::banana::banana: :D
11-29-2008, 05:01 PM
Glow9

Did intel tell you this or was this one of the hand picked ones they wanted you to OC?
11-29-2008, 08:14 PM
Duniek

no possbile???
as my friend says: "EVERYTHING, yes EVERYTHING! is possible but all depends of your wallet thickness" :lol:

I want to see naked i7 too, so pics pls :D
11-29-2008, 08:35 PM
systemviper

1 Attachment(s)

I found a image of the naked i7 :shocked:
\\

Also you can also see die shots and higher resolution shots
HERE
11-29-2008, 08:51 PM
003

shopped. i can tell from some of the pixels and from seeing a lot of shops in my time.
11-30-2008, 01:14 AM
Josifek

I dont think it is worth the 1*C in lower temps to risk such a expensive chip anyway....
11-30-2008, 01:24 AM
jasonelmore

Quote:

Originally Posted by Josifek

I dont think it is worth the 1*C in lower temps to risk such a expensive chip anyway....

I'd say you'd get more than 1C.. probably 10-15C without the IHS. I remember getting at least a 6C temp improvement just by lapping my Q6600.
11-30-2008, 01:27 AM
Josifek

Quote:

Originally Posted by jasonelmore

I'd say you'd get more than 1C.. probably 10-15C without the IHS. I remember getting at least a 6C temp improvement just by lapping my Q6600.

Yeah, the IHS lapping is more benefitial than removing IHS. Especially when solder instead of low quality thermal paste is used...
11-30-2008, 01:30 AM
jasonelmore

Solder?? why would you put solder in between your heatsink/pot and chip? maybe i mis interpreted ya. but the post i got the pic from on page one is a Q6600 with the IHS sanded completely off.. he got over a 10C improvement then stock.
11-30-2008, 01:37 AM
Josifek

Quote:

Originally Posted by jasonelmore

Solder?? why would you put solder in between your heatsink/pot and chip? maybe i mis interpreted ya. but the post i got the pic from on page one is a Q6600 with the IHS sanded completely off.. he got over a 10C improvement then stock.

Yep you got me wrong.... i ment the chip and the IHS. Not the IHS and the Heat sink. Some processors have some kind of a thermal paste between IHS and the chip and some are soldered. The soldered ones are not worth removing...
11-30-2008, 04:52 AM
Hoboclese

how was this discovered? did someone kill a chip or did intel say so? if one was killed pics please
11-30-2008, 06:30 AM
berk

The solder will melt at 166-172°C,set the oven but measure with an accurate thermometer and just pop it off,aluminium foil wrap if necessary.Goes well with Duck. :rolleyes:
11-30-2008, 10:09 AM
chispy

Post a couple of pics of the dead :) cpu.
11-30-2008, 04:08 PM
safan80

1 Attachment(s)

charles
11-30-2008, 05:41 PM
003

It's quite obvious he's not going to post again in this thread. This is hit and run posting at its finest. :D
11-30-2008, 07:11 PM
Fuzzy_3D

Quote:

Originally Posted by FUGGER

The core is soldered onto the IHS and trying to remove will destroy the cpu when it separates the layers. There is also small resistor packs around the core that would get broken on razor insert.

Confirmed.

That's what they said about the Core 2 :D

But how else are you gonna do direct die water cooling?
11-30-2008, 07:30 PM
Vienna

Instead of all this sanding or poping ihs off, I wonder how well a water block milled into the ihs would work? Ha ha, theres an idea for someone!
11-30-2008, 07:48 PM
jasonelmore

Quote:

Originally Posted by Vienna

Instead of all this sanding or poping ihs off, I wonder how well a water block milled into the ihs would work? Ha ha, theres an idea for someone!

Or a water Block Molded or milled to the Direct Die dimensions with the IHS off
11-30-2008, 10:33 PM
clayton

Needs sticky quick! Who knows how many poor souls are attempting this.
11-30-2008, 11:35 PM
eleeter

Quote:

Originally Posted by berk

The solder will melt at 166-172°C,set the oven but measure with an accurate thermometer and just pop it off,aluminium foil wrap if necessary.Goes well with Duck. :rolleyes:

haha, well great idea expect if there is any part of the package that uses solder, goodbye connection. :ROTF:
12-01-2008, 06:24 AM
boblemagnifique

it's true , for Help Charles , i have make the test on my 965XE dead :up:

Don't Remove IHS of your Nehalem Chip

http://www.ixtremtek.com/ixtek/Hardw...A447/test1.jpg

http://www.ixtremtek.com/ixtek/Hardw...A447/test2.jpg

Thank for your Information Charles :clap: , you can put the pics in the first post :up:
12-01-2008, 06:42 AM
eva2000

ouch... nasty indeed!
12-01-2008, 06:45 AM
Movieman

Quote:

Originally Posted by boblemagnifique

it's true , for Help Charles , i have make the test on my 965XE dead :up:

Thank for your Information Charles :clap: , you can put the pics in the first post :up:

just out of curiousity, how did you kill that chip?

Show 100 post(s) from this thread on one page