Quote:
Originally Posted by 5150 Joker
I wouldnt trust rivaTuner.
My multimeter reads a hair under 1.4, so we can safely assume 1.4vGPU
2D mode, it ran 1.166 or something, I have the exact #'s posted in my first post.
Printable View
Quote:
Originally Posted by 5150 Joker
I wouldnt trust rivaTuner.
My multimeter reads a hair under 1.4, so we can safely assume 1.4vGPU
2D mode, it ran 1.166 or something, I have the exact #'s posted in my first post.
Right but you checked an X1900 XT correct? I have an XTX so I'm guessing it runs with a slightly higher voltage (1.45v) and that's what RivaTuner reports. For those of you wondering how to get it to work with X1900 (only hw monitoring works) go to RivaTuner's forums and check out the sticky.Quote:
Originally Posted by irev210
Anyone got more then 725Mhz on GPU stable? i set over ati tool 1.45V to GPU ... mems at 873, anything higher cause artefacts (in deep freeze its nicely visible, black dots), setting higher voltage dont help.
Using 1.55v I can get 760 mhz very stable using ATi Tool.Quote:
Originally Posted by spajdr
isnt that too high lol :p:Quote:
Originally Posted by 5150 Joker
what is the rest of your voltages?
Nah using water so temps never get above 48 C. When setting the memory to 870 mhz I use 2.150v/2.120v for the two memory voltages.Quote:
Originally Posted by spajdr
Ok gonna try it today later, you got Sapphire too? voltages for mems we got same :)Quote:
Originally Posted by 5150 Joker
I have a VF700 on my X1900 XT board. So i redused the stock voltage.
I'm running 600-750 @ 1.15v and 1.9v for 2D and 3D now. It uses a little bit more than the 500-600 @ 1.2-2.1 stock. Because of the high clocks. But its silent and quite cool. The VF700 cant handle Stock X1900 XT 3D clocks and voltages. it will run @ 80c or more with fan @ 100% (12v).
So i need A VF900 or Accelero X2 :D The Stock cooler is a bit to noisy for me. The plastics hood arround the fan is causing that noice by resonating at the fribrations of the fan. But the Stock cooler peforms realy well. A Accelero @ max fan speed wil have a higher temp than a X1900 Stock @ 100% but it will run more silent.
1.55 is much :| i would not date to use it unless i can run @ 60c max. But i well need WC cooling for that. Also take a look at the VDDIC Voltage in ATi Tool. It will help you run your ram more stable. Without i raising that one i could not run 800 MHz without iminate artifacting. If i set VDDIC @ 1.58 i can run it artifact @ 800 MHz free up to 80c core temp. After 80c is lockup.
Stock cooler is crap...i dunno how ati put a cooler like that on a vga with the performance of the x1900 series...
Well did some modifications...
http://img270.imageshack.us/img270/4...01837ot.th.jpghttp://img270.imageshack.us/img270/9...01853te.th.jpghttp://img100.imageshack.us/img100/6...02015bq.th.jpghttp://img270.imageshack.us/img270/7...01863ny.th.jpghttp://img100.imageshack.us/img100/4...01886af.th.jpghttp://img100.imageshack.us/img100/1...01933fv.th.jpghttp://img270.imageshack.us/img270/7...01965lt.th.jpg
http://img270.imageshack.us/img270/3...01959nc.th.jpghttp://img270.imageshack.us/img270/6...02038zd.th.jpghttp://img270.imageshack.us/img270/3...02088if.th.jpghttp://img270.imageshack.us/img270/6...02104id.th.jpghttp://img270.imageshack.us/img270/1...02113yl.th.jpghttp://img270.imageshack.us/img270/5...02126sm.th.jpghttp://img270.imageshack.us/img270/1...02139lg.th.jpg
http://img216.imageshack.us/img216/9...02157jz.th.jpghttp://img216.imageshack.us/img216/7...02172wx.th.jpghttp://img335.imageshack.us/img335/4...00014qr.th.jpg
Just started to see the max gpu speed...mem's default, cpu not maxed, benchs at 3345!
6k would be pice of cake with vga aircooled and single core!
http://img476.imageshack.us/img476/6766/7304dh.jpg
I will put 2tornados later on the card ;)
btw just for the record...
I made a run comparing with my old 7800gtx512mb with same cpu speed and vga's default
Score with 7800gtx512 - 5138
Score with x1900xtx - 5418
Well i have VDDIC at 1.5 and mems are running fine up to 873Mhz.Quote:
Originally Posted by Astennu
Get WC :toast:
Nope mine is Built by ATi brand but it's the same thing.Quote:
Originally Posted by spajdr
You have a XTX :D I got a XT. The XTX are binned for speed. So probaly will clock like 30-50 mhz higher on the core and like 50-100 mhz on the memory.Quote:
Originally Posted by spajdr
I don't like WC. I had WC years ago. Then whent to prmeteia for cpu rest all Air. That was the best for me. Now i'm back @ full air. But the X1900 get realy hot.
I hope the VF900 will do the trick otherwise i'll think of WC got a big case so u would easely fit. But its expecive and the gains are not gigantic.
For cpu u get like 5-10c lower temps Compaired to a good air cooler like Zalman 9500 or TT BT.
wow, 1.15V is real good for 3D stable clocks of 600/750. Makes me wonder why you need up to 1.4v just for 50mhz more on the core which is stock for the XTX. Card should run real cool with those low volts.
Quote:
Originally Posted by 5150 Joker
nope, I got an XTX
I think its the temperature. I I cant get 700 @ 1.45v and also not @ 1.35v. Anyway 1.35v works better than 1.45v. Temps are to high for my VF700 and the X1900 core so i get Artifacts if i get in the 80-90c temp zone.Quote:
Originally Posted by cantankerous
Current temp is like 64C load in ATi tool with zalman VF700 @ 12v. So not quite cool. Stock cooler douse a better job.
Ok, so if I understand this right:
1) Disable ATI hotkey poller
2) Reboot
3) Set core voltage to 1.4v (what about mem?)
4) Overclock
5) Run 3Dmark?
That's about right...you can keep mem voltages the same and you should be able to gain a significant amount on that clock, tho playing with the voltages (more or less, depending) may get you better results.Quote:
Originally Posted by LenniZ
how much mhz are you guys squeezing of yours x1900xt(x) aircooled ???
Gpu...
740 here by now!
I was able to do 760 (XT) on an air cooler I made myself out of an old Volcano 7+ CPU sink :) 800 on water, but it's worse scores than 790. Mem just blows though and won't go over 830 no matter what I do...although I haven't tried over 1.525 on VDDCI, but even that setting didn't seem to help one little bit...
i cant get more then 870 on mems without black dots .. anyone have higher Mhz for RAMs? if so, how much and what voltages set?
My XTX does 990 if I overclock with driveheaven.net's tool (2.006V) and 910 if I overclock with ATITOOL (2.225V / 2.130V).Quote:
Originally Posted by spajdr
Quote:
Originally Posted by D.D.7
wich cooling do you use at those speed?
Thanks
Those are memory speeds. Gpu on water and sinks on memory with a fan. I can bench 805/910 without artefacts.Quote:
Originally Posted by giorgioprimo
The Overlclocker tool uses other memory timings. How where ur 3Dmark socres ith the 990 and the 910 OC ? the gain should be small.Quote:
Originally Posted by D.D.7
What are ur max load temps ?
805Mhz on GPU? omg .. what voltages? anything over 760Mhz at GPU hangs for me, no matter if i set 1.55V on GPU or 1.575Mhz. I got heatsinks on RAMs (from Zalman Cu700) and fan on it, with these voltages you got on RAMs i got small black dots in deep freeze test, its nicely to test it with it, since its visible immediately :-)
Are u uning a Vf700 or a Zalman 7000 CU cpu cooler ? And what are ur temps. He is uning watercooling. And the chips get verry hot. So i u can hold the temp low enough u will be able to hit 800.Quote:
Originally Posted by spajdr
Hehe, i just use heatsinks from zalman Vf700, but on GPU, there is watercooling. Probably my piece is worse, since i cant imagine i could get 800Mhz on GPU, but lets wait on how he set the voltages for GPU :-) on 760Mhz temp is up to 47C under load.Quote:
Originally Posted by Astennu
Is that 47c with H2O ??Quote:
Originally Posted by spajdr
Because i have got a Vf700 Cu on the X1900 XT. And i f u run it @ XTX stock it its 89c !!!!. So i'm running it on 675-775 @ 1.35v ( Stock = 1.45v ). 1.35 is more stable than 1.45v because of the temps.
I'm running 600-750 @ 1.15-1.85 now because of the high temps. My temps are 64c stressed. @ VF700 CU @ 100% Speed.
Yes, its with H2O :-) 760Mhz, VGPU voltage is set to 1.55V, could be less maybe, if i raise Mhz to 770, it hangs in few seconds in tests, setting to 1.575V which is max in ati tool didnt help. But i see that thru overclocker you can set even 1.6V :D
Overcloking with AtitoolQuote:
Originally Posted by Astennu
http://img46.imageshack.us/img46/4707/atitool6pi.jpg
and with overclocker
http://img46.imageshack.us/img46/152...clocker6yt.jpg
I can't bench with 990 without artefacts at this time:mad:
DD7 can you post all voltages when you overclocking with ati tool? with 801/909 clocks, thanks :-)
80 mhz difference in mem speed but only 10 points in the total score. So u see that the overlcoker is using other timings. But will give u almost the same peformance.
spajdr: Wat is ur pwm temp ? i saw a guy @ a other forum that had h2o. and his pwm temp was 75C @load so he made a new heatink for the power regulators. Temp was 45c load after the mod and the whent from 730 > 780 Mhz on the core @ the same voltage:
http://www.ocforums.com/showthread.php?p=4305456
Astennu : got exactly the same temps .. 65-70C .. i will try to catch these heatsinks together lol, i dont want to spend 70 euro on new waterblock with part that cooldown regulators too :-(
http://obchod.nextcomp.cz/data/defau...al/AKA9051.jpg
something like this:)Quote:
Originally Posted by spajdr
http://img444.imageshack.us/img444/4...oltages7mn.jpg
Quote:
Originally Posted by spajdr
just put a fan blowing in power regulators.
thanks mate for info, tried same voltages, but hangs before some 3d scene even starts, ohh well i got worse piece then :slapass:
http://i3.photobucket.com/albums/y55...med-blokk1.jpg
:toast:
Will give this sucker something to chew on the next couple of weeks.
Quote:
Originally Posted by LenniZ
You didn't shave down one of the ramsinks? I have the same block and ramsinks but I had to shave down one of the sinks so the tubes could fit without hitting the sink.
http://i40.photobucket.com/albums/e2...1900XTX001.jpg
http://i40.photobucket.com/albums/e2...1900XTX002.jpg
have to love the getto mod
http://i3.photobucket.com/albums/y90...r/DSC07099.jpg
http://i3.photobucket.com/albums/y90...r/DSC07100.jpg
and some more to come
http://i3.photobucket.com/albums/y90...r/IMG_0790.jpg
It fitted well without any problems at all.
I would love to find out how well that ghetto mod is actually mounted. I would be kinda nervous about that one.
Also i'll try to post some pics of my watercooled X1900XTX tonight.
heres my watercooled XT. The MCW55 sits nice and high so there is no clearance problems even with these tall Swiftech ramsinks.
http://thecowsaysmoo.org/budwise/pic...900XT%20WC.jpg
Are you using the low profile Maze 4 or the regular one? The low profile one like the one I have has clearance issues with one of the sinks.Quote:
Originally Posted by LenniZ
Nicde cooling solutions :D But i whant to stick to air cooling. I will look into the PWM heatink mod. There could be a big gain by doing that mod.
12766 ^^
I'm #4 on the ORB with Sub 3Ghz CPU and X1900XT/XTX :)
i am hoping to get some nice scores on air done tongiht and attempt over 15k in 3D05 and 7k in 3D06.
My card loves the voltage!
Just a quick question regarding those who have disabled the 2 ati services and are using atitool to clock in 2D. Do you find some scores went up but others down? I noticed my 05, 06 and aquamark scores went up using the atitool method over max CCC even at lower clocks however my 01 and 03 scores went down using this method. They weren't down by much but none the less still down. I was hoping for an increase in scores right across the board. Not sure what to make of this any ideas?
13k done :D
http://service.futuremark.com/compare?3dm05=1806564
Currently I'm #3 with sub 3ghz CPU and X1900XT/XTX, the 2 above me is using X2 ;)
Quote:
Originally Posted by cantankerous
its cuz you have lower clock (gpu or mem) speeds with atitool and in 01/03...its more clock speed dependent (both cpu and gpu/mem) when its not gpu limited anymore
aquamark should be lower too...weird that its not
yea it is weird, I understand the clocks are lower but only by 25mhz total across the card, not much. I figured having the tighter timings would have made up for the slight loss in clock speeds much like it did in 05 and 06 which saw an increase. The natures especially. I guess I am not the only one to notice this though eh? I am still fine tuning my card to get more out of it but I want to keep noise and heat to a minimum or am willing to sacrifice some speed to do so. Card is plenty fast as it is now anyhow.
yep, you're not the only one and we're not the only two i bet ;)
i run mine at stock volts with 50% fan speed....beyond that speed it starts to drone/whine too much
yea I know. I have my fan at 27% but it jumps anywhere from 50-77% depending on speeds. I try and keep my core at mid 70's at max which is still in the late yellow area on the CCC overdrive tab temp monitor.
So chinkgai, opinion. Would you say your card is still performing better overall at lower speeds but tighter timings via atitool even though 01, 03 and aquamark are down yet 05 and 06 are up or would you find the card faster when all scores are up even with 05 and 06 not as high as when using atitool you follow?
well that depends on the game you're playing and at what resolutions...
a heavy 3d game at a high res will likely benefit more/less along with the correlation of 3dmark05/06 being up or down
while a less intensive 3d game at a lower res would benefit more correlating along with 01/03/am being up or down
im sure u get the general idea. looks like u got a 20inch lcd so you're at 1600ish resolution...that means whatever (atitool or octool) gets u the higher score in 05/06...then you'll most likely benefit accordingly
as i stated earlier...its nearly identical for me and i dont have to run a high voltage in 2d mode (less heat, longer life?, less power consumption)
if atitool yields you greater results than octool (though it didnt for me) then more power to you ;)
in the end...its much like VX vs TCCD...all depends on which has higher top speed and the results from those top speeds
Ya I figured what you were saying, just wanted a second opinion without feeding you the information you know?
I currently am using ATItool with the services disabled and at 1.35v in 2D mode I have the card set to 677/751 completely stable and crash free. I can loop the 3Dmarks for hours this way without a lockup or crash. I also ran the artifact detector in Atitool for over an hour with nothing. Temps never got past the late 70's in temperature. The card is also artifact free at this. This nets me higher 05 and 06 scores than a max CCC overdrive OC of 689/792. I am still fine tuning the card and trying to get more out of it at the same voltage but I think I am at the end. Anything higher than I have the card set to now nets in a lot more voltage being needed. 1.4-1.425v+ which of course runs the card hotter and the fan louder which I am trying to avoid. I have setup a profile in Atitool to only come on when 3D is initiated kicking the card up to above speeds of 677/751 at 1.35v. When 3D apps are exited or upon windows boot itself the card is left at default profile in Atitool with the card being set at its standard 1.175v 500/600 in clocks. I don't want to have to run 1.35v through the card when it is just browsing the web etc as temps get close to 60c idle this way. I hope I don't damage the card either sooner or later from the shift in both clocks and volts off and on depending on whether I am using the card for 3D or not however even through the ATI drivers themselves clocks and volts shift up and down under load or not so I think this should be fine. Yes? Just want to be sure.
I have not touched the new VDDCI voltage adjustment in Atitool as I still have no clue what it does nor have I read about too many others with a valid explanation on its useage. Do you or anyone know and perhaps I missed it? If raising or lowering this will net me better results please do share as I am in the dark on this one.
Thanks again for everything.
For those of you using watercooling and a maze 4 GPU block, what are your idle and load temps? I'm using a BIX 2 radiator (dual 120mm 79 cfm fans), maze 4 gpu block and a tdx cpu block. My idle temp is around 40-41 C and load is 50 C with the card clocked at 730/832. Another person I know has a similar setup except his XTX idles at 30 C and peaks at 40 C using the same gpu block.
@cantank, unfortunately i have not messed with the voltages at all since my cooling is still "inadequate"
a good person to ask is viperjohn at the atitool beta forums. very very knowledgeable guy as im sure you know.
For any wondering, i just got a HIS x1900xt and the ram is 1.1
The original HSF is stupid! It makes the card overheat and like a hair dryer. :D
And Zalman VF-700cu is not capable of efficiently spreading heat for X1900XT(X), I tried, playing games over 7X~8X deg.C :stick: :slapass:
I just modify the waterblock to suit my X1900XTX and using ATItools 0.25BETA13 to overclock, now, I can keep it around 40deg.C when full load (rm temp. ~ 25deg., but I think mine is not a good clocker.
By setting a 3D profile with Vgpu voltage saved to the profile, it works! ;)
3D06 - 6710marks
http://service.futuremark.com/compare?3dm06=132422
3D05 - 13105marks
http://service.futuremark.com/compare?3dm05=1809491
heres what im getting in 3d05 so far @ 670/774. I just got this card today so im very pleased. one thing that was odd is that my score went down almost 100points after I rebooted and increased settings to 675/800? any one know how this is possible? the only other thing I did different was slightly increase mem voltage a couple notches.
Quote:
Originally Posted by 5150 Joker
Mine idles 35 load 42. Setup in sig...
I got this problem too, the score went down without reboot ;)Quote:
Originally Posted by Daveb2012
BTW, your score is really high for this clock
thanks,Quote:
Originally Posted by TinTin
I actually did reboot between each run. the problem I think is that increasing volts on memory decreased the score slightly.:confused:
I didn't increase the voltages for RAM :DQuote:
Originally Posted by Daveb2012
Yeah this decreased my score overall? Now I have left it alone when I ran a test at 700/800 w/ stock mem volts I got 13379pts. when I raised to 702/823 and increased mem volts to 2.091 My score went down to 13269. I have actually seen in this thread one of the guys who got around 13.5k had his mem volts around 1.8?? drecreased?Quote:
Originally Posted by TinTin
Idle atm is 32 and under load the max is around 45. I have a dual heatercore, maze 4 gpu, and tdx cpu block. The voltage on the gpu core is maxed.Quote:
Originally Posted by 5150 Joker
How hot does the voltage regulator get for you guys? I'm stressing my card out with HDRIBL right now and the voltage regulator is at 77 C right now and seems to be climbing. :explode2: Kinda worried that it's getting too hot, have any of you removed the tape that's on the voltage regulator sink and put AS 5 on them?
Are the HS mounting holes for the x1900 the same as 68/7800 geforces? I've got a water block that i made a custom mount for, for my 7800 and wondering if it will fit on my soon to be x1900xt.
Is that person me? Well, my XT idles at 30c and loads @ 38-40c (depends on roomtemperature)Quote:
Originally Posted by 5150 Joker
really hot, I used a 12cm fan to blow on it and one more 12cm for the back of the display card ;)Quote:
Originally Posted by 5150 Joker
A littlebit benching today :)
39795 3DMark01se
5990 3DMark06
Allright score for a singlecore @ ~3ghz eh?
Yes, same mounting holes as 6800/7800 nvidia cards.Quote:
Originally Posted by menlatin
any one know what the Ideal voltage is for memory on this card? I searched all 7 pages of this thread and cannot find a lot of info. I do see a good bench @ 13.5 with mem volts at only 1.8 which suprised me, decreasing volts? does it work? Im not sure what to do with them but I think this is one factor holding me back.
got me ready to do some action on prommy but , i dont have mobo right now im gone wayt for it to come . hope see likes te cold , here are some pics op the card mounted en ready to use :D
http://i3.photobucket.com/albums/y90...r/DSC07135.jpg
http://i3.photobucket.com/albums/y90...r/DSC07136.jpg
hope thate te mobo comes in today ;)
I didn't check through the whole thread for that particular pic, but if it's a screenshot of the overclocker program then the reason it says 1.8v is because if you change from stock voltage in ATiTool and then open overclocker it will read 1.8. However, some people have been getting 1.9v and around there to work well. I myself am having trouble stabilizing my 840 on the ram atm, i'm trying to set the VDDQ .2v lower than VDDC and it's working better but not stable yet...Quote:
Originally Posted by Daveb2012
The BJ11 on my XT seems to like the volts. It scales up to 2.2V pretty well. Haven't tried any higher since i don't know hom much these modules can take. 2.2V is good for 872MHz using ATI Tool without artifacts.
Quote:
Originally Posted by 5150 Joker
running 2x x1900 cards watercooled with a fx60 watercooled.
cards using dangerden blocks they r 31 idle 40 load m8. and this includes cpu cooling on same loop and 2x cards.
I'm beginning to wonder if the temperature diode on my X1900 is defective or not. My X2 4400+@2.75 GHz (same loop) never exceeds 35 C under load yet my video card peaks at 50 C which doesn't make sense.Quote:
Originally Posted by dazboots
bad mount?Quote:
Originally Posted by 5150 Joker
I remounted it 3 times so it can't be that. I even have 2 80 mm fans blowing on the XTX + OCZ ramsinks so you'd think that would help a bit with overall temps.Quote:
Originally Posted by slayer899
What are the stock 2D and 3D core voltages on the XT?
I know it does on the core, but does the RAM voltage change as well when the card switches to 3D mode?
slayer899:
can u tell me all your voltage settings in ATItools?
Got some problems OC my XT card.
Think some of the problems is caused by my powersupply but not all.
Someone asked for temps on Maze4 GPU block to. Mine is ~38 idle and 48 max
god hates me i think , put the mach2 on the card and cold bug @ -12°c and it get wild :(
Guys how do I extend the clocking ranges available in ccc I have reached the top it will allow me 690,800mhz at stock voltages and on stock cooler no problems at all and want to go further.
Thnaks
Go get ATi Tool from http://www.techpowerup.comQuote:
Originally Posted by pazza316
http://techpowerup.com/atitool to be exact :D
Hey, been messing with ati tool and have found that when i mess with the ram settings itll cause my screen to freeze/artifact ~775mhz, but using the CCC it detected the full 690/800 and was 3d06 stable/artifact free. Has this happened to anyone else?
probably ati tool is setting more aggressive timing on RAMs compared to CCC overclocking tool. Just run your favorite benchie and you should see difference btw overclocking with ati tool or CCC.Quote:
Originally Posted by kemist
Thats possible, but i also forgot to mention that, before i had even flashed to xtx, i had been able to clock it to 780 at least once and it didnt freeze/artifact at all. Ive also had it freeze when adjusting the gpu speed to a speed it had done before same voltages. I might mess with overclocker tonight to see if it produces the same behavior, even tho OC has looser timings its probably better to be able to clock it.
core voltage is 1.575, mem is 2.130/2.110v and VDDCl is stock...speakin of which, do you guys think 1.575v is too high for 24/7 volts if i have WCing with max core temp of 45C?Quote:
Originally Posted by licken
Ok, I think 1.575v on core is little to high for 24/7. Try give the VDDCI more volts and lower the core volts.Quote:
Originally Posted by slayer899
One more question, i cant get memory stable over 801MHz. But in Overclocker i can real high on stock volt but i get lower and lower scores. (Powersupply)
So if i get a new powersupply do u people think i can go higher in ATItools?
Think the volts is very unstable and goes up and down.
I don't think it will hurt the GPU if you peak at 45 C with those voltage settings. I peak at 48 C now using 1.55v on vgpu for 24/7 settings and I haven't had any issues.Quote:
Originally Posted by slayer899
Got a new PSU today. Starting ATItools to se if i could get higher.
But not. Trying higher volts on ram but not a single MHZ higher. Cant even go for 809 in highest setable voltage in ATI tools. :/
Stuck @ 801MHz
Can it be the memory cooling? got som AS5 and "super-glue" on it.
So are the XT's clocking consistantly less than the XTX's, even with XTX bios? I' saw somewhere that the XT's are overclocking about 50-75mhz less on the core, and 100mhz on the ram. But it didn't say if they were XT's with XTX bios. I'm still waiting for my XT to ship (why's monarch so slow?!?!?) and i'm getting more and more anxious about what to expect.
I personally have nothing on the ram, just the waterblock on my gpu and a fan from my heatercore going in the card's directionQuote:
Originally Posted by licken
can we please have more people start posting their overclocks and what voltages & cooling they used to achieve them - i've seen maybe 3 or 4 actual overclock + voltage reports in this 5-page thread, and its not helping me much
Quote:
Originally Posted by licken
Overclocker loosens the mem timings, which is why your score goes down.
yeah, but i get higher with lower freqs. Testing OC now. Think all depends on the VDDIC. i set it to 1.550v and can get 801MHz on memory with standard volts. :SQuote:
Originally Posted by Plywood99
I still have no clue exactly what VDDCI is and how it affects clocks. I wonder why it is only on the X1900 and not the X1800 too.
Quote:
Originally Posted by Sneaky
Yah i will post in the first post if more people start doing it
just
VGPU/MVDDC/MVDDQ/VDDCI
and then your reported overclocks and cooling methods
thank youQuote:
Originally Posted by irev210
PEOPLE!!! PLEASE CONTRIBUTE TO THE x1900XT/XTX VOLTAGE/OVERCLOCKING DATABASE
-Thanks :)