It is Thermalright getting ready with the bracket for this card?
Printable View
It is Thermalright getting ready with the bracket for this card?
Further to my previous post, I did try the Scythe Musashi heatsink. To fit on the GTX460 Sonic Platinum six of the fins needed their middles removed to make way for the DVI connectors, and the (glued-on) heatpipe ends needed removal, followed by the grating of the PCI bracket, so they could just peep through.
Verdict? I found the Musashi disappointing. Its temps weren't really better than stock and could even creep higher, it did cool the VRMs better though.
So, as I'd mentioned I'd try to, I succeeded in fitting a CoolIT ECO ALC to my Palit card instead. :D
http://www.xtremesystems.org/forums/...1&d=1283631668
The 53mm square mounting points actually sit directly on the plastic surround of the ALC's waterblock, so not only do you need to make the brackets (hastily dremeled from an old baking tray, here) but you must sand down the plastic corners of the waterblock so they're not in the way of the bolts.
After that though, the large, flat square base fully covers the GTX 460 chip and its lid. The Musashi did not, though I'm fairly certain it covered most of the silicon itself (haven't delidded to check).
Because of the square nature of the mount the water block can be mounted in any orientation. I found it best with the piping facing the VRMs, then I was able to mount the radiator on the back of the case just like one would normally.
http://www.xtremesystems.org/forums/...1&d=1283631668
Temps? Idles between 27-30 degrees.
Load tips out at 60 degrees, 900/1800/4000MHz @ 1.125V! Yes, 1.125V... my chip wasn't a good one :( games tend to run slightly cooler than Kombustor, perhaps 55ish?
60c under water, this isnt that good ...
:eek: I'm only at 67°C in SLI (F@H 840 core). Lowest card is 7°C cooler. Damn Gigabyte :rolleyes:Quote:
Originally Posted by bhavv
I think that this guy just has terrible case cooling or something:Quote:
Originally Posted by ctgilles
http://forums.hexus.net/graphics-car...ml#post1966034
They really shouldnt be that bad.
Me thinks that this thing will be just as effective as the Cyclone cooler plus a side fan :pQuote:
Originally Posted by Drewlander
Its better to just get the cyclones if you arent planning to watercool them.
Yeah, but it's not really water, is it? Look at the size of the radiator, too. The CoolIT ECO is not designed to compete with proper watercooling kits.Quote:
Originally Posted by Boulard83
Having said that, it's nearly thirty degrees cooler than all my air-cooling attempts with this card, and I can finally hit 900MHz (crap chip, remember), and it's silent. I am, for now, content :D
Here some reply's from manufactures that are developing a GTX460 kit;
AC
"Hi there,
Thank you for your email.
We are about to release an adapter of MK-13 for the GTX460 cards which follow the nVidia's reference design.
It will be released within 2-3 weeks.
We would like to inform you via email once it's released."
"Dear Sir,
Yes,you can try our Accelero XTREME Plus,the compatible set for GTX 460 will be release within one month,please check our website regularly for latest update.Please check the following webpage for information.
http://www.arctic-cooling.com/catalo...ath=2_&mID=619
Have a nice day"
Scythe
Thank you very much for your inquiry and interest in Scythe items.
"We indeed have more than just plans to support the mentioned
VGA Card. As it is complaint to Nvidia GeForce GTX460 mounting
holes and even has its own heatsink for the Voltage Regulators,
means it should be possible to use the upcoming Setsugen 2 VGA
Cooler. You can get details about Setsugen 2 from our latest product
catalog(Page 12 & 13), which you can see/download from our ftp server:
ftp://ftp.scythe-eu.com/Scythe-Katalog-2010-Q3-4.pdf
http://www.overclock.net/nvidia-cool...l#post10663134
Is the MCW80 stock fit with the GTX460 or i need a mounting kit ?Quote:
Originally Posted by azureoval
Just ordered for my 2 GTX460
3x Swiftech MC14 BGA Memory Heatsinks (8 Pack) $41.31
3x Swiftech MC21 Aluminum Heatsinks $21.66
2x Swiftech MCW80 GPU Water Block $87.82
170$ shipped
http://img.directcanada.com/images/S.../MC21/MC21.jpg
http://img.directcanada.com/images/S.../MC14/MC14.jpg
http://img.directcanada.com/images/S...CW80/MCW80.jpg
I assume your Asus cards are reference? If so that won't work. Gabe (Swiftech CEO) says that the MCW80 GTX460 brackets are still a couple of weeks away.Quote:
Originally Posted by Boulard83
You could also get two full cover XSPC blocks for about the same money. Although you wouldn't be able to use them on a videocard later on.
http://www.performance-pcs.com/catal...ducts_id=29167
They are DirectCU.
Ill make it work. With a little thinkering, everything can work together !
Edit : I wrote to swiftech to have any input about this.
Im lazy, this is about as far as I will go trying to cool my cards.
this is some good VRM sink :)
GPU @ 925mhz/1.087v (this one wont go really far above 925, not that good binned)
Room : 29°c
Idle : 32°c
Load Kombustor : 41°c
http://www.infodupat.com/MiscPics/DSCF2186.JPG
http://www.infodupat.com/MiscPics/DSCF2190.JPG
Ummm ! Why didn't you bought 2 x 470gtx and simply OC them at stock cooling ?..... perf wise it would be better.Quote:
Originally Posted by Boulard83
Cause GF100 never interested me. The efficiency is just to bad. YES it would be better with 2 GTX470 (performance wise)..... but WCing the GTX470/480 is just not an option, its NEEDED. 2 GTX470 + waterblocks ... its never ending !
Im mostly waiting for the GTX475/485 to see if they worth selling 2 of my cards and keep a GTX460 as PhysX.
Nice 'case' :p:Quote:
Originally Posted by Boulard83
http://hostthenpost.org/uploads/b7ad...837c80878c.jpg
And 925MHZ, 1.087 isn't all that bad. Flash the bios and take the Vgpu a bit higher.
Thanks alot lowfat, i know the guy that tempted you for this case ;)
Im very pleased with it. Added the top 120mm for better airflow on the mobo/gpu/ram
http://www.infodupat.com/MiscPics/DSCF2186.JPG
I hated mine until I took the dremel to it. Couldn't install my RAID card, soundcard. And couldn't use the top DVI port on any video card I installed pretty much. :down:Quote:
Originally Posted by Boulard83
I agree that some modding can be needed in some case, but i really love the Bench type of case. So usefull.Quote:
Originally Posted by lowfat
Yeah, seems kinda incomplete. Best go back to the drawing board.. :clap:Quote:
Originally Posted by OC Nub
^^ Actually the gpu's run cool but the vrm area of the card felt rather hot, so I thought I would give this a try. If that didnt fix it I would just sell them and go back to my crossfire setup. Spending a small fortune to cool a mid level gpu makes no sense to me, would be better off to spend the money on a higher end card, unless you are benching for boints at hardwarebot or something like that.
I've noticed that too, my Asus GTX460s are burning up at the VRM area and I've even lapped the VRM heatsink and used some AS Ceramique instead of the crappy thermal pad. Beyond that would be better lapping and keeping just the VRM heatsink and using screws instead of the rather odd backplate with pushpins Asus have chosen to use. On the plus side I can do 855MHz @ 1.05v.
^ Does your board have the large space between the cards like on some other Asus boards? I went back to the Gigabyte UD7 from the R3E, slots 1&3 are very close on the UD7 and the cards are almost touching each other. I can see a 10c difference between the top and bottom card. I will probably put them back in the R3E, temps are more even and cooler.
Yep all 3 PCIE slots are spread pretty well. Really starting to erk me though trying to figure out why the VRMs are getting so hot.
Seems Thermalright are on the case. shame it's so huge!
http://www.techpowerup.com/img/10-09-15/105b.jpg
Thermalright Readies Shaman 140 mm VGA Cooler
If would be great if you could mount the fan on the underside of the heatsink, blow air away from the card it would only be a 3 slot cooler then. Which would make SLI possible on some boards.
Thermalright coolers is so good , but too big , taking up 3 slots its quite possible .
Forget about Crossfire / SLI user .
Really can run SLI / Crossfire on some boards ?Quote:
Originally Posted by HackJoe
Not as it currently is, If you replaced the 140mm fan with a slimline 120mm then maybe but you'd lose the CFM and as a result the great temps.Quote:
Originally Posted by vern
Thermalright just need to make a slimmer version. Many motherboards have Crossfire/Xfire layouts allowing for 3 slot coolers. So I'd imagine they'd sell enough.
Come on Thermalright, slim it down.
Take it theres still no joy on the aftermarket cooler front for the palit sonic 1gb cards ?
seem so, but I'm waiting water block from EK
Quote:
"New full cover block for non reference Geforce 460GTX cards - 14/10/2010
We are developing new full cover block for Palit and Gainward GeForce 460GTX series.
Blocks will be available on 5th of November."
The ZEROtherm COOLMAXX 3000 might fit this card?
If you want to make a good performance , you must pay for it .:DQuote:
Originally Posted by HackJoe
Wow. I wouldn't have thought EK would make a block specifically for just 1 manufacturer.Quote:
Originally Posted by Nage
I hope they will do that
btw the news from their site
http://www.ekwaterblocks.com/index.p...t01returnid=17
ok ... one question
on a refrence pcb which all coolerz can b mounted? ... or we shud wait 4 new co
ive a sparkle coolerz
Is Thermalright going to release the bracket for this Video card?
October supposed to be the ETA
Hey peeps, I have 2 palit sonic platinum 460s and I was wondering if there is some other kind of fan I can install on the original heatsink they have by removing the whole factory plastic cover+fan. Any suggestions? What fans have the same pins as those of graphics cards?
I used something like this to the card direct.
http://www.newegg.com/Product/Produc...82E16835186034
but later i just got a faster 4pin molex fan with controller and strapped it on.
Hi all, just to say that i bought the mk-13, it works amazing on my gigabyte gtx 460 768, but i had to use the stock cooler retention system to tighten the screws but only 2 of them were possible.I overclocked it to 870 core and 2000 mem and my temperatures in furmark are amazing and just with one 120mm 1000rpm NB xl1. :shocked
max temperature was 74ºC after 5min.
Gigabyte GTX-460 768 MB (GV-N460DS-768I-B)
http://www.bjorn3d.com/read.php?cID=1900
I only hear the PSU! lol
http://img705.imageshack.us/img705/6339/img1185j.th.jpg
http://img846.imageshack.us/img846/3316/img1188b.th.jpg
http://img651.imageshack.us/img651/5803/img1189m.th.jpg
edit: http://img198.imageshack.us/img198/6858/img1194g.jpg
and the solution is:
http://img816.imageshack.us/img816/3...3153730223.jpg
:shocked:
I think the http://www.zerotherm.net/eng/product/CM4000.asp]ZEROtherm COOLMAXX 4000 will fit. There is a couple of reviews at the bottom of the pagen in Korean.Quote:
Originally Posted by Parad0x
To bad I cant seem to get it here in Sweden :down: