G.Skill Trident triple channel kit - DDR3 @ 2000 MHz in test

Printable View

Show 100 post(s) from this thread on one page

08-11-2009, 02:07 PM
aver

Quote:

Originally Posted by mk_dir

Exactly, it's not necesary remove the heatspreader to know your Trident chips.... just check how long they can go on CL7-8-7-20 timings (1,65V), 1.9Ghz or above, means BBSE for me.
No name chips can't reach configs like these.

I can't get mine to boot at 2Ghz on my DX58SO.. Definitely cannot run CL7 at 900 on 1.65Vram and 1.45QPI... Even using the XMP settings mine won't boot at 2000...
08-11-2009, 03:40 PM
zoqiet

I had my Trident's run through 32M superPI atm @ 1532 6-7-6-20 @ 1.5v/1.16vtt.
But after the run i noticed only 4gig of ram was detected, one of the sticks failed to work :/.
Edit: Even 1.65v won't work. Although, 7-7-6-20 seems to be working , @ 1.5v. But, with either tCL or tRCD at 6, regardless of vdimm and vtt it seems to be failing, but only on one of the sticks. I smell bad egg :<
http://bildr.no/thumb/466609.jpeg
08-11-2009, 03:58 PM
aver

Quote:

Originally Posted by zoqiet

I had mine run through 32M superPI atm @ 1532 6-7-6-20 @ 1.5v/1.16vtt.
But after the run i noticed only 4gig of ram was detected, one of the sticks failed to work :/.
Edit: Even 1.65v won't work. Although, 7-7-6-20 seems to be working , @ 1.5v.

Would CPU Voltage effect my ability to run the RAM at higher speeds? I cannot boot 180x10 1.65Vram 1.3QPI at 7-8-7-24 ? I can boot 8-8-8-24 at 1.62V 1.3QPI and 1.1 IOH (Do I need to up IOH at all?)

My CPU is stable at 3.78Ghz (180*21) @ 1.184 Vcore

But I cannot boot this ram @ 2000 even with default timings on my board..
08-11-2009, 10:14 PM
hiwa

that's your mainboard problem :up: Smackover
is not a good mobo for testing ram
08-11-2009, 10:16 PM
hiwa

Quote:

Originally Posted by aver

HyperPi or SuperPi?

1 X 32m ;)
08-11-2009, 10:25 PM
mk_dir

Quote:

Originally Posted by aver

HyperPi or SuperPi?

For stability test, I prefer Prime on blend test.

Quote:

Originally Posted by aver

I can't get mine to boot at 2Ghz on my DX58SO.. Definitely cannot run CL7 at 900 on 1.65Vram and 1.45QPI... Even using the XMP settings mine won't boot at 2000...

That was bad news, BBSE Tridents can reach 1.9Ghz CL7 easily.

Quote:

Originally Posted by aver

Would CPU Voltage effect my ability to run the RAM at higher speeds? I cannot boot 180x10 1.65Vram 1.3QPI at 7-8-7-24 ? I can boot 8-8-8-24 at 1.62V 1.3QPI and 1.1 IOH (Do I need to up IOH at all?)
But I cannot boot this ram @ 2000 even with default timings on my board..

To run @ 2Ghz with that Tridents maybe you would need more QPI voltage. Set your memory at that speed it's harder when you system is overclocked, the increase of BCLCK makes the uncore (and the IMC) run at higher clocks.

Try tu use high multiplier for you CPU, set your memory at 9-9-9-24, and give the VTT more voltage.
08-12-2009, 05:11 AM
aver

Quote:

Originally Posted by mk_dir

That was bad news, BBSE Tridents can reach 1.9Ghz CL7 easily.

:(

Quote:

Originally Posted by mk_dir

To run @ 2Ghz with that Tridents maybe you would need more QPI voltage. Set your memory at that speed it's harder when you system is overclocked, the increase of BCLCK makes the uncore (and the IMC) run at higher clocks.

Try tu use high multiplier for you CPU, set your memory at 9-9-9-24, and give the VTT more voltage.

What is a safe limit on the QPI Voltage ?

Right now I am running 9-9-9-24 (XMP Profile) but @ 900 Mhz instead of 1000. I have been running prime for approx 12 hours CPU @ 3.7 Ram @ 900 and no errors. CPU is set at 1.25Vcore (CPU-z Shows 1.18) ram is still at 1.65v and QPI was at 1.45 but I lowered it to 1.3. I ran memtest on the ram last night to ensure there were no errors and it can back clean.

I am starting to suspect that my motherboard may be the issue. Is the Gigabyte UD5 a good board to use? I don't want to spend all that much money and its really the only somewhat afford one of the group.

Edit:

I got them to post at 1000Mhz but I had to up QPI to 1.5 nothing below that would post.. What does that indicate?

Here is what mine look like from the side. I can't tell which ones I have but I doubt its the BBSE unless my MOBO hates tight timings..

http://imgur.com/r0pfU.jpg
08-13-2009, 07:04 AM
mk_dir

Definitely 1.5V VTT voltage it's too much for a 24/7 config. Whats your uncore frequency??
08-13-2009, 07:34 AM
aver

Quote:

Originally Posted by mk_dir

Definitely 1.5V VTT voltage it's too much for a 24/7 config. Whats your uncore frequency??

The only config I could get these to boot in was 10xRam Multiplier and 20xUncore with 200Mhz FSB 1.65Vram and 1.5QPI ..

But same settings 10x180 would not post.. I am going to RMA the set and pick up the Mushkin XP3-12800 Redline which are supposed to have the BBSe's in (keep my fingers crossed).

Also when switching Mobo's I am looking between the DFI, UD5, or P6T Deluxe V2? Any opinions on which one would be the best?
08-13-2009, 01:54 PM
zoqiet

Quote:

Originally Posted by aver

The only config I could get these to boot in was 10xRam Multiplier and 20xUncore with 200Mhz FSB 1.65Vram and 1.5QPI ..

But same settings 10x180 would not post.. I am going to RMA the set and pick up the Mushkin XP3-12800 Redline which are supposed to have the BBSe's in (keep my fingers crossed).

Also when switching Mobo's I am looking between the DFI, UD5, or P6T Deluxe V2? Any opinions on which one would be the best?

Your problems are most likely with the Uncore and IMC, not the RAM.
For the motherboards I'd say DFI > P6T, UD5.

.....

Finally figured out what were wrong with my dimm channels as one dropped out on C6. And I blamed the poor sticks. :<
Trident's currently running at 1600mhz 6-7-6-20 @ 1.53volt linX stable. Not bad sticks for 120euro tbh!

http://bildr.no/thumb/467875.jpeg
08-17-2009, 09:09 AM
drakore

Quote:

Originally Posted by zoqiet

Your problems are most likely with the Uncore and IMC, not the RAM.
For the motherboards I'd say DFI > P6T, UD5.

.....

Finally figured out what were wrong with my dimm channels as one dropped out on C6. And I blamed the poor sticks. :<
Trident's currently running at 1600mhz 6-7-6-20 @ 1.53volt linX stable. Not bad sticks for 120euro tbh!

http://bildr.no/thumb/467875.jpeg

What was wrong? I am having the same issue
08-17-2009, 05:21 PM
namegt

Hello.
G. Skill Trident triple channel kit test
Over clocking a short easy to use

http://cfile2.uf.tistory.com/image/1...4A89551BBF0BF2

http://cfile1.uf.tistory.com/image/1...4A89551CC008CC

http://cfile22.uf.tistory.com/image/...4A89551DC14FE5

http://cfile3.uf.tistory.com/image/1...4A89551EC22BFA

http://cfile1.uf.tistory.com/image/1...4A89551FC3C5BA

http://www.playwares.com/xe/files/at...4/006/2000.jpg
2000MHz 8-9-8-24 1T 1.65v

http://www.playwares.com/xe/files/at...394/006/32.jpg
2100MHz 9-9-9-24 1T 1.65v
08-18-2009, 08:03 AM
drakore

ughh my 3rd channel keeps dropping out on this overclock, not sure why. It happened after i OC'd my CPU, when i had the CPU at stock, it passed 2 hours of memtest.

This is my OC:

CPU vCore 1.26875
QPI/Vtt 1.275
IOH Core 1.1
Dram 1.64
Load-line disabled
CPU PLL 1.8
PCIE 1.5
QPI PLL 1.1
IOH I/O 1.5
ICH Core 1.1
Dram Term 0.75
CH-A Data (all other channel voltages similar to this) 0.75
Performance Standard
QPI x36
Uncore x20 3200
Isochronous Enable
BCLK 160
Ram Multi 10
08-31-2009, 04:46 AM
Ragnarok

This stuff looks fantastic for the price (less than 1/2 the cost of corsair here), gonna pick up some tomorrow and see how it goes!
09-21-2009, 10:57 AM
..::G80::..

http://www.memoryc.com/products/desc...kit/index.html

Same memory? How much is max voltage for elpida chips?
09-24-2009, 07:13 AM
eva2000

First hour with Gskill Trident 2000mhz kit :)

http://nx.i4memory.com/reviewimages/...dent2000_2.jpg http://nx.i4memory.com/reviewimages/...dent2000_3.jpg http://nx.i4memory.com/reviewimages/...dent2000_4.jpg http://nx.i4memory.com/reviewimages/...dent2000_6.jpg

http://nx.i4memory.com/reviewimages/...dent2000_7.jpg http://nx.i4memory.com/reviewimages/...dent2000_8.jpg http://nx.i4memory.com/reviewimages/...ent2000_11.jpg http://nx.i4memory.com/reviewimages/...ent2000_12.jpg

First overclock on these and not bad for 8x 32M Pi @DDR3-2124Mhz 9-9-9-24 1T at 1.72v. Asus P6T6 WS Revolution bios sets latencies pretty tight so good pi performance even for Win7 OS :)

Both 8x 32M Pi and single 32M Pi runs done in same windows session.

http://fileshosts.com/intel/Asus/P6T.../hpi32m_x8.png

http://fileshosts.com/intel/Asus/P6T...9m10s213ms.png
09-24-2009, 08:41 AM
GSKILL TECH

If anyone has any questions or needs assistance with memory BIOS configuration, please feel free to PM me. Sometimes it is hard to browse through all the forums and catch all the questions.

Thank you
GSKILL SUPPORT
10-04-2009, 07:11 AM
eva2000
Wonderful memory these Tridents are. New personal best cpuz memory validation and first time breaking DDR3-2300Mhz for triple channel on X58 @DDR3-2305Mhz 9-10-9-24 1T at 1.78v. Previous best was @DDR3-2298Mhz 9-9-9-24 with 3GB Samsung HCF0 modules.

System:
- Intel Xeon W3540 3845B010
- EK Supreme LT 1366 / FESER 480 / MCP655
- Asus P6T6 WS Revolution
- Gskill Trident F3-16000CL9T-6GBTD
- 512MB Inno3D 8800GT OC Edition 190.62WHQL
- 750GB Samsung SATA
- Pioneer DVR-217 DVD-RW
- Corsair HX1000 PSU
- Dual Boot - WinXP Pro SP3 (nLite fully updated) with Vista Theme & Win7 Ultimate 64bit RTM
Max Validation @DDR3-2305Mhz 9-10-9-24 1T at 1.78v

QPI/DRAM = 1.65625v
VDIMM = 1.78v
Uncore frequency = 4608Mhz :)

http://valid.canardpc.com/cache/banner/747628.png

http://fileshosts.com/intel/Asus/P6T...cpuz_valid.png

Super Pi 2M @DDR3-2256Mhz 9-10-9-24 1T at 1.78v

http://fileshosts.com/intel/Asus/P6T...m_22s651ms.png

Show 100 post(s) from this thread on one page