Guide Thread

Printable View

Show 100 post(s) from this thread on one page

08-08-2008, 03:25 PM
Big Lar

Quote:

Originally Posted by Praz

Big Lar

Please see this post I just put up at the club.

http://csd.dficlub.org/forum/showthread.php?t=7645

Just read it, Thank you again Kind Sir. you are a wealth of information and I am always happy when you reply.

Larry
Edit; I always run with VDroop enabled, I figure the board knows more than I.
08-08-2008, 03:36 PM
Praz

Quote:

Originally Posted by Big Lar

Edit; I always run with VDroop enabled, I figure the board knows more than I.

Under load the voltage should be dropping close to the value you have set.
08-08-2008, 04:58 PM
nfm

Quote:

Originally Posted by Big Lar

Got a question, running a Q9XX0 chip and when I set Vtt and Vcore in bios 05/21/08 my settings always read a bit higher than the actual set voltage in bios, ie; if I set 1.2650v for the cpu I get 1.29v bios and 1.31v SG. Vtt, 1.26v set, 1.29v bios. Anyone having thrown a meter on the board running this bios that confirm or give any insight into this?

I am getting a bit too old to be trying to take measurements on the board with a dmm, as I would between my bad eyes and not so steady hands blow the darn thing up.
Thanks.

Larry

+1 to what Praz said. I believe that 5/21 overvolted Vcore by 0.04v but don't take my words, I think it was do to my crappy multimeter. I checked Vcore on 3/17 BIOS using a good DMM.

BIOS, CPU-Z Idle, CPU-Z Load, DMM Idle, DMM Load
1.36250v | 1.376v |1.360v | 1.379v| 1.359v
08-08-2008, 06:25 PM
Big Lar

Quote:

Originally Posted by nfm

+1 to what Praz said. I believe that 5/21 overvolted Vcore by 0.04v but don't take my words, I think it was do to my crappy multimeter. I checked Vcore on 3/17 BIOS using a good DMM.

BIOS, CPU-Z Idle, CPU-Z Load, DMM Idle, DMM Load
1.36250v | 1.376v |1.360v | 1.379v| 1.359v

How close was it on 03/17? Having a problem ironing out GTL's is why I ask...NM didn't see the voltages in the bottom.
Larry
08-08-2008, 11:40 PM
OnDborder

Anyone try an e8600 on this board yet?
08-09-2008, 04:55 AM
mad_skills

What's the difference between 05/02 and 05/21 bios?
08-09-2008, 05:12 AM
Praz

Quote:

Originally Posted by OnDborder

Anyone try an e8600 on this board yet?

Works fine.
08-10-2008, 05:35 AM
Big Lar

Quote:

Originally Posted by mad_skills

What's the difference between 05/02 and 05/21 bios?

Nothing besides reported voltages that I can see. 05/02 seems to reports volts a tad lower than 05/21. They clock the same for me on the quad I am testing.

Larry
08-10-2008, 06:02 AM
kitfit1

Quote:

Originally Posted by Big Lar

Nothing besides reported voltages that I can see. 05/02 seems to reports volts a tad lower than 05/21. They clock the same for me on the quad I am testing.

Larry

For my E8500 05/02 is rock solid. But 05/21 does seem to be a bit hit and miss, and in fact i have never been able to get it to run more than 9hrs in Prime blend. 05/02 runs all day long no problem, go figure.
08-10-2008, 06:29 AM
mad_skills

Tnx ppl, i think i'll stay on 05/02 for the time being.
08-13-2008, 01:56 PM
RNeon

Hello,

where i can buy this Mobo in europe?? or in a US Shop who ships to Germany?
08-13-2008, 04:26 PM
deadman'sclick

Quote:

Originally Posted by RNeon

Hello,

where i can buy this Mobo in europe?? or in a US Shop who ships to Germany?

ebay if ur lucky
08-13-2008, 04:28 PM
ether.real

Quote:

Originally Posted by RNeon

Hello,

where i can buy this Mobo in europe?? or in a US Shop who ships to Germany?

I have a used one I can sell you. PM me if you are interested.
08-13-2008, 06:39 PM
Apache0c

Does anyone have the little silver rectangular plate and the 4 screws that go with it for mounting the transpiper?
08-14-2008, 10:07 PM
nfm

My memory hurts, this mobo did not came with CPU backplate right? :yawn2:
08-14-2008, 10:21 PM
zsamz_

Quote:

Originally Posted by Apache0c

Does anyone have the little silver rectangular plate and the 4 screws that go with it for mounting the transpiper?

just make 1 you can even make it outa copper for real cheap
08-15-2008, 12:33 AM
kitfit1

Quote:

Originally Posted by Apache0c

Does anyone have the little silver rectangular plate and the 4 screws that go with it for mounting the transpiper?

I would'nt bother with it if i were you. It dos'nt lower temps, and more than likely blocks the flow of air through the case.
08-15-2008, 03:44 AM
C-N

Anyone had the privilege of running a 4870x2 on this board yet?

I take it there are no weird compatibility issues.

CN :)
08-15-2008, 05:30 AM
cantankerous

Good question C-N. I hope not as I am sure many are going to go this route. If there is an issue I hope Oskar will sort it soon with a bios update. Haven't had one in a few months now, probably won't have anymore unless issues arise. I think we are seeing all we are going to see for options and performance from this board.
08-15-2008, 10:13 PM
-Zork-

Are there anyone who use USB KEYBOARD or USB MOUSE to POWER ON???,

I configured like the manual said and don´t work on LT P35 with bios 502
08-15-2008, 10:37 PM
Apache0c

Quote:

Originally Posted by kitfit1

I would'nt bother with it if i were you. It dos'nt lower temps, and more than likely blocks the flow of air through the case.

I was thinking about mounting it to my southbridge. I'm sure one of you has it laying around since it seems like hardly anybody uses it. Will someone please send/sell it to me?

Thanks
08-15-2008, 11:34 PM
zsamz_

2 Attachment(s)

i swapped my x38 for the p35 n :) for my e8600
some quick runs:D
i'll test max fsb later
08-16-2008, 03:01 AM
zsamz_

how to put cpu multiplier to 8.5 is it possible?
08-16-2008, 03:10 AM
mad_skills

Nice E8600 man, real sweet cpu.:up:
08-16-2008, 03:27 AM
zsamz_

Quote:

Originally Posted by mad_skills

Nice E8600 man, real sweet cpu.:up:

tks i likin the cpu so far i think a p45 mighta been more easy but no fun
load temps a bit high on air after 1.4v need to bump ac up
need 1.46v on nb to be stable @4.6 1.39v
i been away from p35 for a while what is safe max nb voltage i load @ 36c@1.46v

Show 100 post(s) from this thread on one page

**Official DFI LanParty UT P35-T2R Review/Overclock/Guide Thread**

Official DFI LanParty UT P35-T2R Review/Overclock/Guide Thread