Printable View
^^
i've seen that too and wondered about it but never really thought much about it.
----------------------------------------------------------------------------
new daily settings: 4.4ghz @ 1.40625 vcore, 68*c average temp. w/HT off.
http://i3.photobucket.com/albums/y71...lus/daily2.jpg
Ya, it's not gona stop me from using a high multi if that's the setting that works best for what I'm trying to do, but I would like to know why it does it and how to fix it.Quote:
Originally Posted by skuldarin
Windows assumes stock multi is being used and goes off BCLK only so it will calculate BCLK x stock multi and give you the speed in sys info.
Aren't you taking a big performance hit with 2t cammand rate and ht off. :sofa:
^^^
not really actually. tested with both T2 and T1 on the same timings and it seems to come out the same every time on what programs i have to test it. i DON'T have everest though which would show in detail what i'm missing out on but nothing else seems to be noticing a difference.
I just finished reading this whole thread. Took me about a week and I don't think I retained
half of the information, but thanks to all of you guys I have learned a lot.
I need some help with linx and any suggestions at all with my settings.
I can pass prime95 but linx stops with error after first loop. My average temp is below 70c.
I can drop my vcore if I go to 4500MHz but stops linx after two loops. Here's my settings:
Code:Target CPU Frequency 4600MHz
Target DRAM Frequency 2005MHz
LN2 Mode [Disabled]***
QPI Loadline Calibration [Enabled]***
Sync Mode []
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
2D Performance Booster [Disabled]
CPU Ratio Setting [23.0]
CPU Turbo Power Limit [Disabled]
>CPU Configuration----------------------------
CPU Ratio Setting [23.0]
C1E Support [Disabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetch [Enabled]
MPS and ACPI MADT ordering [Modern ordering]
Intel(R) Virtualization Tech [Enabled]
CPU TM Function [Disabled]
Execute Disable Bit [Enabled]
Intel(R) HT Technology [Enabled]
*Active Processor Cores [All]
A20M [Disabled]
*Intel(R) SpeedStep(TM) Tech [Disabled]
Intel(R) C-STATE Tech [Disabled]
C State package limit setting []
C1 Auto Demotion []
C3 Auto Demotion []
----------------------------------------------
BCLK Frequency [200]
PCIE Frequency [100]
DRAM Frequency [DDR3-2005MHz]
UCLK Frequency [3008MHz]
QPI Link Data Rate [Auto]
Memory Configuration Protect [Disabled]
>DRAM Timing Control--------------------------
CAS# Latency [ 8 DRAM Clock]
RAS# to CAS# Delay [ 8 DRAM Clock]
RAS# PRE Time [ 8 DRAM Clock]
RAS# ACT Time [24 DRAM Clock]
RAS# to RAS# Delay [Auto]
REF Cycle Time [Auto]
WRITE Recovery Time [Auto]
READ to PRE Time [Auto]
FOUR ACT WIN Time [Auto]
Back-To-BackCAS# Delay [Auto]
Timing Mode [1N]
Round Trip Latency on CHA [Auto]
Round Trip Latency on CHB [Auto]
Round Trip Latency on CHC [Auto]
WRITE To READ Delay(DD) [Auto]
WRITE To READ Delay(DR) [Auto]
WRITE To READ Delay(SR) [Auto]
READ To WRITE Delay(DD) [Auto]
READ To WRITE Delay(DR) [Auto]
READ To WRITE Delay(SR) [Auto]
READ To READ Delay(DD) [Auto]
READ To READ Delay(DR) [Auto]
READ To READ Delay(SR) [Auto]
WRITE To WRITE Delay(DD) [Auto]
WRITE To WRITE Delay(DR) [Auto]
WRITE To WRITE Delay(SR) [Auto]
----------------------------------------------
CPU Differential Amplitude [Auto]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-Balanced]
PWM Volt. Control [Auto]
Load-Line Calibration [Full Calibration]
CPU Voltage OCP [Enabled]
CPU PWM Frequency [Auto]
Extreme OV [Disabled]
Extreme OC [Auto]
CPU Voltage [1.47500]
CPU PLL Voltage [Auto]
QPI/DRAM Core Voltage [1.30000]
DRAM Bus Voltage [1.65625]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM DATA REF Voltage on CHB [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHC [Auto]
DRAM CTRL REF Voltage on CHC [Auto]
----------------------------------------------
IOH Voltage [1.15275]
IOH PCIE Voltage [Auto]
ICH Voltage [1.15275]
ICH PCIE Voltage [Auto]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Auto]
PCIE Spread Spectrum [Auto]
***on-board jumper dependant
Bump up your Vtt (QPI) 1.30v is probably too low for DDR3-2000 MHz. Try something like 1.3625v (probably about 1.32v real) and see if that helps.Quote:
Originally Posted by zinsco
Quote:
Originally Posted by CryptiK
Well, I tried higher Vtt but no joy. Why is it that I can run prime95 no problem, but linx is a no go?
Do I have wrong settings maybe, or does linx put more stress?
Thanks, that's correct and may be why the mod does not work. I looked through all 36 modules in the BIOS with a hex editor and notepad, and none are Intel AHCI ROM, so this may by why the new ROM fails to load, some other module in the BIOS would also need edited to call the new RAID ROM into action.Quote:
Originally Posted by Brama
I ran into a similar issue trying to mod the 10.1.0.1008 ROM into some EVGA BIOSes for users a few weeks ago, they are in a similar boat with no Intel AHCI ROM either, so without the manufacturer editing in the newest ROM it's not going to work using normal end user mod methods.
10.1.0.1008 is a good ROM though, so you guys should be fine with that. I am not sure what was in your BIOS before this one, but many boards are still using 9.6 or earlier (Updated a few from 8.0-8.5 last week), so at least you now have 10.1.0.1008 anyway!
@ C300 SSD users - if any of you are thinking about setting up RAID on the Marvell 9128 controller please see my C300 review linked in my signature! This controller cannot handle SSD's in RAID, and speeds will be slower than that of a single drive (When it's not crashing on you during a bench :D) Gigabyte has even edited their specifications for boards with these controllers, adding that SSD RAID should not be used.
try running with HT off maybe and try manually setting qpi data link manually at closest to 6400 and then try toying with your rTL's manually as they tend to be choosen too tight or too loose when set to auto.Quote:
Originally Posted by zinsco
New bios 1301 ftp://ftp.asus.com.tw/pub/ASUS/mb/LG...e_III_Extreme/
Wow that was fast. I wonder what the changes are.Quote:
Originally Posted by SOYLINDA
I'm wondering if the new Marvell FW and option ROM will possibly solve this issue? I don't have 2 C300s to test with, but the new BIOS I got from MrToad (SEE HERE) for the Rampage III Gene fixed all the issues I was having just trying to have the computer recognize the drive to install Windows. Might be able to input the same Marvell package into the 1301 release for the Extreme.Quote:
Originally Posted by Lsdmeasap
Quote:
Originally Posted by zinsco
try changing that 4.6 is to high for it to runn TBQuote:
Digi+ PWR Mode [T-Balanced]
I figured out how I can put them on the Intel controller, I cant believe how I overlooked it before ...Quote:
Originally Posted by zoson
Move the DVD drive to a marvel port, then I have two free Sata II ports :)
So now I just need to wait for the 64 Gb C300 to go on offer, which should happen as soon as the M4 is released
Thanks for the advice, I'll keep a look out for 64 Gb C300 reductions over the next few weeks.
Yeah Bios 1301 is on the ftp site!
ftp://ftp.asus.com.tw/pub/ASUS/mb/LG...ge_III_Extreme
Thanks, Deboyzfun for the info. Getting it now and i wonder what the deal is with this one. Two of them released in one month. Odd indeed but i like they are doing them though that fast.
technical question, should i connect both EZ_PLUG while running two way sli or one is just enough?! cause i'm having some kind of stabilty problems ...
I assume you have one card in the first pci-express and the other in the third. I do believe each ez plug powers the two shared lanes. So the first plug will power 1rst & 2nd pci-express. And the other will do the 3rd & 4th slots.
They are both on the same power plane so use either.Quote:
Originally Posted by p3gaz_001
I cleaned up the thread from some irrelevant posts over the last pages.
Carry on and be nice.
Just a quick question.
I'm running SLI with 2x 480's in slot #1 and #3, this blocks off my PCI slot for my soundcard, Do I have to skip this soundcard and use the built in one? :(
Why not place it in the forth one? Or is it too tall to go in the second lane? As you know they will work in a full pci express lane also. Also forgot to mention if you are using the hard sli-bridge, just use a long flex cable maybe.Quote:
Originally Posted by haxxie
by now i've plugged EZ_PLUG2 .. i do not have enough cable to reach the EZ_PLUGQuote:
Originally Posted by KILLER_K
OK, i'll be using the second one.. in a second time, i'll connect the first to if it works the same... thank you!.Quote:
Originally Posted by Raja@ASUS
:up:Quote:
Originally Posted by Jupiler
.. unless you buy a single slot video card bracket.Quote:
Originally Posted by haxxie
in the users manual it's wrote that, 2 way sli is only supported on slot 1 & 3.Quote:
Originally Posted by KILLER_K
Quote : in the users manual it's wrote that, 2 way sli is only supported on slot 1 & 3.
At x16, yep 1 and 3 but wil work in any combination of slots just with different speeds.