Alright different chip now again,. The other one was pushing 94c at 3.5GHz. This one is a 170 batch and has a vid of 1.2375 which is ok because it is running a hell of a lot cooler then the other one. This one is running Prime95 right now @ 480 x 8.5 4GHz and a temperature of 65c on the hottest core, muchhhh better. I will push it more here in a little bit. Hoping I can set my games up on my new install and play some now, finally..
hi guys
love the overclocks
but i have a problem with my overclock
here is the specs of my rig
gigabite ep45ud3r
intel q9450 2.66 @3.5 with true extreme 120 2x silenx 120mm 90cfm fans in push pull temp 63c max with intel burn test
ocz ddr2 1066 @1055 2x2gb
asus gtx280
enermax 1kw psu
im having problems getting the cpu over 3.6 and i have took the voltage to 1.3v and i cant get is stable
i dont really know about the motherbord voltages and whats (safe) so i dont like to mess about just incase i damage the mobo i reall wanted to hit 4ghz but can i do it with air and what temp is really to high for the overclock
thanks to anyone that can help me
Try just setting your CPU voltage to 1.35 and your chipset to 1.4 and then your memory to 2.1 and leave everything else auto except the performance level and your memory strap. All of your gtls at auto at first. Mine I have noticed this for a fact now after having this motherboard for about a week now that if I set the gtls my self at first it won't boot, leave them at auto and vualua boot.Quote:
Originally Posted by rubber5
I also noticed that if I leave my memory at 1.8v it won't boot either. I think the motherboard thinks because the memory is running at 1150MHz it needs 2.1 and it won't let me boot with out it set to that. Kind of a weird thing but, whatever the memory is running cool at that voltage any way. Hope that helps.
Once you get a feel for what to set the volts to the lowest possible volts, then start setting your gtls one by one checking for stability every time you make a change until you have everything else manually set as well.
Guys I just had the weirdest issue with this board. Upping the PCI freq to 105 resulted in a continuous reboot, anyone else ever have this issue?
Not sure why you would run it that high. 100-101 is what i use.Quote:
Originally Posted by The Viper
Quote:
Originally Posted by The Viper
UD3 series can only run till 102Mhz_PCI_eQuote:
Originally Posted by OC Nub
Extreme series can go much higher.
huh, ok, thanks guys...has anyone been able to run PL8 on 2.4B divider at or above 500FSB?
EDIT: Can someone tell me on what page the templates for 4.5GHz are, I know Ive seen a couple
Most of us run 2:40>Turbo>PL8>4500Mhz.Quote:
Originally Posted by The Viper
Just posted what you want over Q9650 thread, just click on my link.
Hi Guys
Can Somone Give Me Some Information
I Can Set Ram Frquency To 1438Mhz Realy Realy Hard This Link
And I Know Divider 3:5 Is Bug On Giga P45 Set 1568Mhz This Link But This Cheat 1410 Mhz Realy
I Need To Know My Fault To Get More Frquency Many Other My Friends Can Set 1500 Mhz With That Moudle Ram
Some Bios Setting:
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:
PCI Express Frequency (Mhz) .........:Auto
C.I.A. 2......................................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 1000mv
PCI Express Clock Drive.................: 900mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: [Disabled]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 4.00B
Memory Frequency (Mhz) ..............: 1,333Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time..........................: 6
tRCD ...........................................: 6
tRP..............................................: 6
tRAS............................................: 18
Advanced Timing Control [Press Enter]
tRRD...........................................:Au to
tWTR..........................................:Aut o
tWR............................................:Au to
tRFC...........................................:70
tRTP...........................................:4
Command Rate (CMD) ....................:Auto
Channel A
Channel A Timings Settings [Press Enter]
Static tRead Value.........................:10
tRD Phase0 Adjustmen...................:Auto
tRD Phase1 Adjustment..................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)...................:10
Twr2wr(Different Rank)..................:10
Twr2rd(Different Rank)..................:10
Trd2wr(Same/Diff Rank).................:11
Dimm1 Clock Skew Control.............:Auto ps
Dimm2 Clock Skew Control.............:Auto ps
DDR Write Training .....................: Auto
Channel A Driving Settings [Press Enter]
Driving Strength Profile...................:Auto
Data Driving Pull-Up Level...............:Auto
Cmd Driving Pull-Up Level................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto
Data Driving Pull-Down Level...........:Auto
Cmd Driving Pull-Down Level............:Auto
Ctrl Driving Pull-Down Level.............:Auto
Clk Driving Pull-Down Level..............:Auto
Channel B
Channel B Timings Settings [Press Enter]
Static tRead Value.........................: 10
tRD Phase0 Adjustmen....................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment ..................:Auto
tRD Phase3 Adjustment...................:Auto
Trd2rd(Different Rank).....................:10
Twr2wr(Different Rank).....................:10
Twr2rd(Different Rank).....................:10
Trd2wr(Same/Diff Rank)....................:11
Dimm1 Clock Skew Control...................:Auto ps
Dimm2 Clock Skew Control...................:Auto ps
DDR Write Training .........................: Auto
Channel B Driving Settings [Press Enter]
Driving Strength Profile...................:Auto
Data Driving Pull-Up Level.................:Auto
Cmd Driving Pull-Up Level..................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto
Data Driving Pull-Down Level...............:Auto
Cmd Driving Pull-Down Level................:Auto
Ctrl Driving Pull-Down Level...............:Auto
Clk Driving Pull-Down Level................:Auto
CPU
Load Line Calibration......................: [Enabled]
CPU Vcore...................................:1.500v
CPU Termination…..... 1.200V*........:1.700v
CPU PLL...............1.500V*.............:1.75 v
CPU Reference.........0.755V*..........:Auto
MCH Core..............1.100V................: 1.64v
MCH Reference.........0.800V..............: Auto
MCH/DRAM Ref..........0.900V...............:Auto
ICH I/O.................1.50V...............: Auto
ICH Core............……1.100V...............:Auto
DRAM
DRAM Voltage..........1.800V...............: 2.7v It's Too High I Know But Worked
DRAM Termination......0.900V...............: Auto
Channel A Reference...0.900V...............:Auto
Channel B Reference...0.900V...............:Auto
[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3......................: [Disabled]
No-Execute Memory Protect..................: [Disabled]
CPU Enhanced Halt (C1E)....................: [Disabled]
C2/C2E State Support.......................: [Disabled]
x C4/C4E State Support.....................: [Disabled]
CPU Thermal Monitor 2(TM2) ................: [Disabled]
CPU EIST Function..........................: [Disabled]
Virtualization Technology..................: [Disabled]
I'm Use Water Chiller For CPU And All Other On AIR
NB Too Hot Ram Warm But Not Bad
This SPD My Ram:
http://shahrsakhtafzar.com/img/out.p..._Untitled1.jpg
ok thanks pal i will try it the other thing is what is the max temp you would push out of these cpus i dont want to burn it out i would like to keep the rig for at least 4 years if you know what i meen and i have the cpu voltage set to 1.18v and it can hit 63c with intel burn test and i think it was about 58 with prime so if i take it to 1.35 i kow it will go well over 80c what do you thinkQuote:
Originally Posted by truehighroller
Hi folks, I intend to invest in a UD3P/UD3R Gigabyte board and just had a quick question...
Are the
UD3P and the UD3R basically the same board with different slot configuarations etc...or does one clock higher than the other:confused::confused:
Also this is important....Has anybody ever NOT been able to break 471??? (minimum Q9550 fsb for 4.0 GHZ) on either of these two boards???? or is 475-530 pretty much consistent????:rolleyes::rolleyes:
Cause I be gettin' this strictly for the Quad benefit
otherwise I got the two other X48's
I wanna take a Q9550 to 4.0 - maybe 4.2 GHZ
Also I need something to do this Fall......:p::p::p:
Thanks:up::up::up:
IMO, and I have a bit of experience here. The boards will clock the same. If you're not planning on running crossfire, the r will definitely do it for you.Quote:
Originally Posted by Gameman
You'll need to talk to ocnub about the q9550. He's had his well over 4000mhz. I'm sure he'll be by here before too long to give his input
You gotta feel it out a lot with this motherboard that is for sure, that is it takes some effort but, it is worth it once you unleash it's power and get all your settings set. . I just now settled at 485 x 8.5 because I am on air right now, and that is about all my Thermalright Extreme can really handle TBH. I have already begun piecing together what I will be purchasing, then I can have some more fun. I say get the board, I did.
I've run 2 different Q9550's in my UD3P, as well as numerous dual cores and a Q9650, none had ANY issue at all getting 500+ FSB 24/7 stable, all with 8GB installed :up;
I've noticed the chipset gets pretty warm on my motherboard as well with this one compared to my P5Q Deluxe that I was running. This chipset is almost as if they tweaked the hell out of it or I guess they could of just got high binned north bridges. It is a very good board though IMO.
Hi. Would Thermalright IFX-14 cooler fit the GA-UD3P without any problems?
According to TR's site, it should fit ok.Quote:
Originally Posted by Swordsman
http://www.thermalright.com/new_a_pa...cl.htm#asusp45
hi guys to anyone that is overclocking there quads over 1ghz how can you tell of your north brige and south brige is NOT overheating.
Is there anything you can use to check the temps becuse everest tells me its rinning at 55c but it does not change when under load
THANKS GUYS
Hi guys just a quick question, whats the differnce betweent the rev 1.0 and 1.1 GA-EP45-UD3P?
I can buy a used one and that is a 1.0 so that why im asking, thanks.
Quote:
Originally Posted by rubber5
You should probably look in to lapping your TRUE (Heatsink). I would also consider lapping your CPU. Make sure it is a keeper first though, before lapping the CPU that is because it will then be yours forever unless you sell it on Ebay.
I am going to lap mine now I know I have a good one. Temp wise, I am pushing 81C with my 9550 with Intel Burntest. Nothing else will get it above 65C - 70C so I am not concerned with this. I would aim for temps around there mate.
well i didnt put my true on my q9650
my 26$ cool master 212 slaped it :rofl: -4-8c
Quote:
Originally Posted by zsamz_
Maybe I should get one :p: .
forgot to sayQuote:
Originally Posted by truehighroller
cool room 212 is better 20-24c
hot room true is better
the 212 is verry sensitive to ambient temps and needs a second fan
to be honest i wished i bought 2 more to replace my true and my sons v8
The rev 1.1 has the northbridge heatsink flipped to allow for more CPU cooler compatibility. It also ships with F6 BIOS instead of F4.:)Quote:
Originally Posted by Earzz
Has any one gotten over 556 FSB using a quad on a rev 1.1? The most I've gotten to boot from mine is 550.
I can boot fine @ 533(sometimes 534), but that's with a C1 9550/air. Probably more a limitation of the chips' stepping, than the mobo. :(Quote:
Originally Posted by thebluemeanie1
edit: oops, sorry...mines rev 1.6