Prime Blend ? I prefer to use OCCT 2H ram test to verify the settings... might be ya PL is also a tad too low for those speeds, NB voltage to low for those settings, TRFC... one dimm capping out,...could be some many things...
Printable View
@ Leeghoofd
Prime Small FFTs seems to be no problem with 600FSB @ 1.42v NB voltage...
http://www.abload.de/img/600fsb0kh.png
Chri$ch: what is your settings in bios? It's an amazing FSB you get. I've currently writing a review of this board, and have not so much more time to tweak and search for the best settings, so you would help me alot if you came with some tips. :)
I guys.
I Ricieved my P5Q Deluxe yesterday... everything on AIR
After several minutes, having connected board achieve this result
http://valid.x86-secret.com/ccpuz.ph...5519&nocache=1
http://valid.x86-secret.com/show_oc.php?id=375519
Regards
these settings should allow it to post and be stable for sure, if the CPU doesn't need it better for you and back down...
Think I've found my 24/7 settings for the E8500... 1.3125 in Bios set for Vcore drop to a nice steady 1.28 under load...(again a gain in comparison with the P5K Dlx where I needed 1.29 to be stable)
http://users.pandora.be/OAP/P5QDlx/E8500247.JPG
Yes, Prime Blend. I use OCCT as well but mostly Prime Blend if I really want to know I am stable long term and, so far, I am 7.5 hours stable @ 1.24V 400FSB Strap/1066MHz. I will test 1.22V when I get home this morning.
I have tested each 2x1GB kit and each set was able to reach 450FSB. They passed MemTestPro but failed Prime95.
I'm sure if I raised the PL I could pass at a lower NB voltage, that is a given, but with Ai Clock Twister already set to moderate I don't want to lose anymore performance if I can help it. I will keep testing until I figure this out....
I've come to the conclusion that I'm doing something wrong here . No matter what I try I cannot get a POST over 450 fsb , 450 runs prime fine and 460 , 475 , 500 = no POST . Using the same X3360 and a 780i I was getting into vista @ 3.992ghz but no higher and prime wouldn't even run , it ran at 3.88ghz prime stable for about 5 days before the board died . I'm using latest bios from Asus site , any help would be great .
ASUS P5Q DLX Template :
JumperFree Configuration Settings
AI Overclock tuner: manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: AUTO
FSB Frequency: 450
PCI-E Frequency: 100
DRAM Frequency: 900-1081
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
2nd Information :
READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO
3rd Information :
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO
Common Performance Level AUTO
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.36875-1.4
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.5-1.6
FSB Termination Voltage: 1.3-1.4
DRAM Voltage: 2.26
NB Voltage: 1.2-1.5
NB GTL Reference: AUTO
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.5
Load Line Calibration: enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal
Advance CPU Settings
CPU Ratio Setting: Manual @ 8.5
CPU VID: Default (don't have this option )
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled ( don't have this one )
CPU TM Function: Enabled
Execute Disable Bit: Disabled
How are you guys getting your PL level in windows? I cannot get memset3.5 to work on this motherboard. I get a "NOT FOR THIS CHIPSET" error.
Does someone have a new version of memset or something?
As for my overclocks, this is much better than my P5K Premium or Maximus Formula.
P5K Premium has better PL levels and memory performance IMO.
Current overclock, completely stable (PRIME95, blend,small,large). I can get the same settings on both my P5K Premium and Maximus with lowest voltages on all three. The maximus however would not let me run my 4x1GB KingstonHyperX 8500 @ 1066, the P5K & P5Q not a problem. Also notice that I'm running at the lowest voltages for every section, I was in fact able to boot in Vista and run benches @ 550FSB with a voltage bump only on the RAM @ 1.9.
8400@4G
JumperFree Configuration Settings
AI Overclock tuner: manual
CPU Ratio Setting: AUTO
FSB Strap to North Bridge: 333
FSB Frequency: 444
PCI-E Frequency: 100
DRAM Frequency: 1067
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: AUTO
DRAM Static Read Control: AUTO
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: MANUAL
Common Performance Level 08
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.3375
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.50
FSB Termination Voltage: 1.10
DRAM Voltage: 1.80
NB Voltage: 1.10
NB GTL Reference: AUTO
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.50
Load Line Calibration: AUTO
CPU Spread Spectrum: enabled
PCIE Spread Spectrum: enabled
CPU Clock Skew : AUTO
NB Clock Skew : AUTO
Advance CPU Settings
CPU Ratio Setting: AUTO
C1E Suppport: ENABLED
Max CPUID Value Limit: DISABLED
Intel® Virtualization Tech: ENABLED
Vanderpool Technology: ENABLED
CPU TM Function: ENABLED
Execute Disable Bit: ENABLED
Alpha bios causes puckering of back door...How close to full build are they ? Do they appear to be reliable and stable ?
Memtest 3.5 is working fine in vista 32b.
This chipset is awesome, 500fsb with mems 5:6 1200 @ only 1.16vNB, blend stable. Still cant get to 600fsb but i've found my 24/7 settings :)
This is stable?? :shocked: :shocked::shocked:
can you test a 450fsb and diferent frequency of 900mhz for me??? :p: :D
Here it is, 8.5x500 1.16vNB:
http://i30.tinypic.com/2woyqer.jpg
What multiplier do you want me to use in the 450fsb test?
8x mate! :p:
more frequency than 900mhz to memorys plz!
thanks!
I received mine yesterday and its dead today :( , i was trying very hard for max fsb for validation and a quick aquamark bench E8400 under Dice at 602 FSB and 8800Ultra Under Dice 902/2248Mhz , then bum it crashed and never posted again , back to RMA on monday asap.
Last Pictures taken of the casualty of subsero temps :(
http://i157.photobucket.com/albums/t...7_06150001.jpg
http://i157.photobucket.com/albums/t...7_06150002.jpg
R.I.P............................................. .................................................. .................................................. ......................
Wow...thanks a lot mate!
Update my result with watercooling again :)