** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Sorry if this is a bit noobish, how do I copy and paste my bios settings like:

Quote:

---

Originally Posted by Hoss331

Try this one.

Code:

---

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto    ]
CPU Clock Ratio.................................[ 9        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 4.05GHz...........................[ 450 x 9.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 450      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 800mv  ]
PCI Express Clock Drive.........................[ 900mv  ]
CPU Clock Skew..................................[ 0ps    ]
MCH Clock Skew..................................[ 0ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 400      ]
System Memory Multipler.........................[ 2.00D    ]
Memory Frequency 1066...........................[ 900      ]
DRAM Timing Selectable..........................[ Manual  ]
 
CAS Latency Time................................[ 4      ]
tRCD............................................[ 4      ]
tRP.............................................[ 4      ]
tRAS............................................[ 12      ]
 
******Advanced Timing Control******
 
tRRD[3].........................................[ 3      ]
tWTR[3].........................................[ 3      ]
tWR[6]..........................................[ 6      ]
tRFC[54]........................................[ 52      ]
tRTP[3].........................................[ 3      ]
Command Rate (cmd)[0]...........................[ 2T      ]
 
******Channel A Timing Settings******   
 
Static tRead Value        [ 8 ] ................[ 9      ]
tRD Phase0 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment    [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)  [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)  [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)  [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings******
 
Drive Strength Profile..........................[ 1066    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******   
 
Static tRead Value        [ 8 ] ................[ 9      ]
tRD Phase0 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment    [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)  [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)  [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)  [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings******
 
Drive Strength Profile..........................[ 1066    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore        [ 1.15    ]...................[ 1.37500 ]
CPU Termination  [ 1.20    ]...................[ 1.280  ]
CPU PLL          [ 1.50    ]...................[ 1.500  ]
CPU Reference    [ 0.760  ]...................[ 0.835  ]
 
MCH Core          [ 1.100  ]...................[ 1.280  ]
MCH Reference    [ 0.760  ]...................[ 0.850  ]
MCH/DRAM Refernce [ 0.900  ]...................[ 1.050  ]
ICH I/O          [ 1.500  ]...................[ 1.500  ]
ICH Core          [ 1.100  ]...................[ 1.100  ]
 
DRAM Voltage      [ 1.800  ]...................[ 2.100  ]
DRAM Termination  [ 0.900  ]...................[ 1.050  ]
Channel A Ref    [ 0.900  ]...................[ 1.050  ]
Channel B Ref    [ 0.900  ]...................[ 1.050  ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

---

---

Keep a copy of the template in a txt file, then when you want to post it click the # symbol on the reply page and paste.

Anyone know where I can get a hold of a rev 1.0 UD3P?
Thanks

Been overclocking an EP45-UD3R, w/ a Q9550, w/ 1.25 VID.

Before I go crazy, I'm going to stop @ 3.4; I got to 3.5 w/ some somewhat crazy numbers, but I just can't figure it out going above 3.5. Temps are not a problem, just stability in IDT, OCCt, Prime95. I read and tried alot of voltage settings. Oh well, truthfully, I only needed to go to 3.4 for gaming and every day use. I thin my 800 speed G.Skill ram held me up.



.

Have a temp issue I need help figuring out. I have a E7500 in a GA-EP45T-UD3LR running at 4 GHz (8x500FSB) and my CPU Temp reads about 10 degrees hotter under testing than my Core #1 and #2 temps do. For instance CPU=65c and Core 1/2=55c This is the case in both the newest version of Everest Ultimate, HWMonitor (Pro and free), and Speedfan. I know the E7x00 IHS are only glued not soldered so I'm not sure. Also, both my core temps only go down to 40c at idle, so evidently I have stuck sensors too, although my CPU temp will go down to 25c at idle. Should I be concerned?

I can't go past 300 FSB, I refuse to lower my memory anymore and it doesn't even appear to help the OC any... I'm stuck at 3.9 for the time being... but I'm sure just like I was stuck at 3.64 before, some experimentation might cure this. As of right now though, I'm tempted to start toying with timings and other things. I can pull 22,800 in 3DMark 05, at the default test settings. Is this good, or bad (or about even for that matter)?

This is at 3.9Ghz, DDR2-1000 (5-5-5-15) and a Core 216 at 734/1476/1161


Anywhere, here are my settings:

NB Strap (Latch) = 200 (only 200 strap works)
Using 3.33C...

FSB = 300
PCI-E = 101

Vcore = 1.45
VTT = 1.1
PLL = 1.45
My REF voltages are close enough to 60% of VTT that's all i can recall.. +- about .010v

MCH is 1.2, and the rest is stock.

My Memory voltages are 2.080, and the rest of the associated voltages values are half of 2.080 so 1.040.

Memory Timings are set to 5-5-5-15, everything else is auto (As tight as I can get them).

That's probably spot on and it's the best I can recall while I'm here at work.

People always reccomend "LATCH=Auto" which is the same as strap I assume, and ideally that should be setting it to something that I can select manually. The best of my understanding is that it would be 4.00C, which would put my memory at 1200, well above what it can run, so no, it can't run at that. Simple suggestions aren't solving an obviously complicated problem. I tried every strap last night, nothing works but 2.66C at 345 (and below), 3.33C at 300 (and below), and 4.00C at 280~ and below...

I'd like to see something in the 3.9 area with 1120 memory and if I could only get 3.33C working that'd be possible but nooooooo... board and cpu don't like to place nice.

Specifically, does anybody know what I can do to make some of these straps work higher up in the FSB ranges? 3.33C at 300 would be simply amazing and would bring my memory around to where it should be.

Anything I haven't specified is at Auto. Tips, suggestions? Different bios? I'm running out of my own suggestions these days.

Aynjell, how to you get 3.3 or 3.0 from a FSB of 300.....? What cpu you using?


..

I can not fully stable with 4.3GHz, memtest ok, IBT Standard OK, but hangs in IBT maximum :confused: :shrug:

Looks like this is optimized and Orthos stable. Any higher on the CPU requires less RAM, and any higher on the RAM requires less FSB, etc... : http://i383.photobucket.com/albums/o...can/Pi24-7.jpg

Quote:

---

Originally Posted by dekruyter

Aynjell, how to you get 3.3 or 3.0 from a FSB of 300.....? What cpu you using?


..

---

The 3.33C you're looking at is the ram strap name. :ROTF:

3.33/3:5 is borked, its really only 3.0/2:3

this is a nice boot that i did the other day and run some tests...just on PL AUTO

http://img41.imageshack.us/img41/731...530x85run2.jpg

Hi guys this is one of my first posts for overclocking, been on this website for a little while now and reading through some of this thread, alot of great stories with this board.

So after getting my gear together this is what I've got and what the settings and the results are below...

Mobo: GA-EP45-UD3P (Bios - F9)
CPU: Intel Core 2 Duo E6600 2.4GHz (currently overclocked to 3.49GHz)
Ram: G.Skill DDR2 4GB Kit PC8800 1100MHz
Case: Cooler Master HAF-932
CPU Fan: Can't remember the name but massive heatsink and fan
Graphics: 1 x Gigabyte GTX-285 and 1 x Geforce 7900 (for tripple monitor setup)
HDD: a couple of HDD...

I attempted to overclock my CPU, just by changing the bus frequency and RAM ratios.. At the moment I've overclocked it to 3.496GHz with ram sitting at 1165Mhz and ran PRIME for 10hrs without a problem. I didn't want to adjust any of the voltages as I wouldn't know where to start. If I go up just one more cpu frequency then the system crashes after 1 second in PRIME, so I've left it at 437 for now.

Below is all my BIOS settings, just wondering if you could look through it, see if I need to change anything to see if I can push this puppy any further. I prodominately use this computer for playing games (rFactor) and surfing the net etc...

Code:

---

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto    ]
CPU Clock Ratio.................................[ 8        ]
CPU Frequency 3.49GHz...........................[ 437 x 8  ]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 437      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 700mv  ]
PCI Express Clock Drive.........................[ 700mv  ]
CPU Clock Skew..................................[ 0ps    ]
MCH Clock Skew..................................[ 0ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
Extreme Memory Profile (X.M.P)..................[ Auto    ]
(G) MCH Frequency Latch.........................[ Auto    ]
System Memory Multipler.........................[ 2.66D    ]
Memory Frequency 1066...........................[ 1165    ]
DRAM Timing Selectable..........................[ Manual  ]
 
CAS Latency Time................................[ 5      ]
tRCD............................................[ 5      ]
tRP.............................................[ 5      ]
tRAS............................................[ 15      ]
 
******Advanced Timing Control******
 
tRRD[4].........................................[ 4      ]
tWTR[4].........................................[ 4      ]
tWR[13].........................................[ 13      ]
tRFC[68]........................................[ 68      ]
tRTP[4].........................................[ 4      ]
Command Rate (cmd)[0]...........................[ Auto    ]
 
******Channel A Timing Settings******   
 
Static tRead Value        [ 10 ] ...............[ Auto    ]
tRD Phase0 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment    [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)  [ 8 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)  [ 8 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)  [ 7 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings******
 
Drive Strength Profile..........................[ Auto    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******   
 
Static tRead Value        [ 11 ] ...............[ Auto    ]
tRD Phase0 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment    [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment    [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)  [ 8 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)  [ 8 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)  [ 7 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings******
 
Drive Strength Profile..........................[ Auto    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Disabled ]
CPU Vcore        [ 1.325  ]...................[ Auto    ]
CPU Termination  [ 1.200  ]...................[ Auto    ]
CPU PLL          [ 1.500  ]...................[ Auto    ]
CPU Reference    [ 0.760  ]...................[ Auto    ]
 
MCH Core          [ 1.100  ]...................[ Auto  ]
MCH Reference    [ 0.760  ]...................[ Auto  ]
MCH/DRAM Refernce [ 0.900  ]...................[ Auto  ]
ICH I/O          [ 1.500  ]...................[ Auto  ]
ICH Core          [ 1.100  ]...................[ Auto  ]
 
DRAM Voltage      [ 1.800  ]...................[ Auto  ]
DRAM Termination  [ 0.900  ]...................[ Auto  ]
Channel A Ref    [ 0.900  ]...................[ Auto  ]
Channel B Ref    [ 0.900  ]...................[ Auto  ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Enabled  ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
CPU Thermal Monitor.............................[ Enabled  ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Enabled  ]

---

At the moment as I said, everything is working fine, I ran PRIME for 10 hours and the temperature of the CPU did not go over 55C

Just wanting to see if I've configured it correctly and if I can push anything more out of it, I'm only using air cooling...

Thanks for your time

Dave

HELP!
Started messing with ET6 and when the machine rebooted, it went to the GB splash screen and just stays there. Have tried clearing the CMOS (with and without the battery) and have pulled the batt and unplugged for an hour. Still splash screen only. Have tried delete, F buttons, and tab to no avail.
Any ideas?

Hey, can someone give me a link explaining how the CPU termination and reference voltages work and what they affect?

I've been trying to get my Q9550 stable at 4ghz for a few hours on the UD3P and have been so far unsuccessful. I know it is those settings as raising the CPU voltage does not seem to make any difference.

I tried some of the settings other ppl. found successful, and had a no-go so far.

Thanks

@adpr_02

This link is the best I can offer ** How to setup CPU/MCH GTL Ref Voltages Vs. EasyTune ** , it´s done by Lsdmeasap over at Tweak Town Gigabyte forum, great work from him.

MCH Ref is likely what you need to adjust adpr_02, along with Vtt of course.

If you need any help with the guide let me know. I plan to re-write it so it is more clear but i just have not had time yet

Okay, I read that guide twice, and I'm not sure I'm understanding it 100%. I get what's going on with Et6, but:

Say that I have my VTT at 1.2 and set the reference voltage to x. I now raise the VTT voltage to 1.28 and now my reference voltage goes to x + .050. What's the point of that?

Do you OC pros set your VTT to whatever you desire and then tweak the refference voltages, or go back to stock on the VTT and then set the refference and raise the vtt?

I'm sure that's where I'm getting stuck. I need some help to get started with some pointers and I'll tweak the rest myself. Here are my settings so far. whenever I change the reference and vtt my pc is either completely unstable (won't start) or will run linpack for 2 tests after which it will error.

Any advise on how to set up the references is appreciated. thanks


Q9550 C1(trying to reach stable 4.0, goal 4.2ghz)
******Motherboard Intelligent Tweaker (M.I.T.)******

Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio...........................[0.5]
CPU Frequency 4.03GHz...........................[ 475 x 8 ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 475 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]

******Advanced Clock Control******

CPU Clock Drive.................................[ 900mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]

******DRAM Performance Control******

Performance Enhance.............................[ Standard ]
Extreme Memory Profile (X.M.P)..................[ Disable]
(G) MCH Frequency Latch.........................[ 333]
System Memory Multipler.........................[ 2.00B ]
Memory Frequency 1066...........................[ 950 ]
DRAM Timing Selectable..........................[ Manual ]

CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]



******Motherboard Voltage Control******

Load-Line Calibration...........................[ Enabled]
CPU Vcore [ 1.365 ]..
CPU Termination [ 1.280 ]
CPU PLL [ 1.570 ]
CPU Reference [ 0.835 ]

MCH Core [ 1.380 ]
MCH Reference [ 0.850 ]
MCH/DRAM Refernce [ 1.000 ]
ICH I/O [ 1.500 ]
ICH Core [ 1.100 ]

DRAM Voltage [ 2.200 ]
DRAM Termination [ 0.910 ]
Channel A Ref [ 0.910 ]
Channel B Ref [ 0.910 ]

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
CPU Thermal Monitor.............................[ Enabled]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled]

Edit: with these current settings Linpack will give an error after the first test is done.

Try the value that I have made in bold, it shouldn´t be far off.

Quote:

---

Originally Posted by adpr_02

I'm sure that's where I'm getting stuck. I need some help to get started with some pointers and I'll tweak the rest myself. Here are my settings so far. whenever I change the reference and vtt my pc is either completely unstable (won't start) or will run linpack for 2 tests after which it will error.

Any advise on how to set up the references is appreciated. thanks


Q9550 C1(trying to reach stable 4.0, goal 4.2ghz)
******Motherboard Intelligent Tweaker (M.I.T.)******

Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio...........................[0]
CPU Frequency 4.00GHz...........................[ 500 ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 500 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]

******Advanced Clock Control******

CPU Clock Drive.................................[ 900mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 50ps ]

******DRAM Performance Control******

Performance Enhance.............................[ Standard ]
Extreme Memory Profile (X.M.P)..................[ Disable]
(G) MCH Frequency Latch.........................[400] If you use 400 compare to 333, you can go one lower with "Static Read Value"(tRD, aka Performance Level) when you is done OC that CPU
System Memory Multipler.........................[ 2.00? ]
Memory Frequency 1066...........................[ 1000 ]
DRAM Timing Selectable..........................[ Manual ]

CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]



******Motherboard Voltage Control******

Load-Line Calibration...........................[ Enabled]
CPU Vcore [ 1.365 ]You may need more
CPU Termination [ 1.280 ]~1-28-1,36
CPU PLL [ 1.570 ]
CPU Reference [ ~0,810 ] Around 63,5% of CPU Term should work with a 45nm quad, maybe one step up or down from that should do it

MCH Core [ 1.380 ] Seems a bit on the high side, try around 1,32-1,36
MCH Reference [ ~0,890] Around 70% of CPU Term should work with a 45nm quad, one step up or down from that should do it
MCH/DRAM Refernce [ Auto ]
ICH I/O [ 1.500 ]
ICH Core [ 1.100 ]

DRAM Voltage [ 2.200 ]
DRAM Termination [ Auto ]
Channel A Ref [ Auto ]
Channel B Ref [ Auto ]

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
CPU Thermal Monitor.............................[ Enabled]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled]

Edit: with these current settings Linpack will give an error after the first test is done.

---

Quote:

---

Originally Posted by Aynjell

I can't go past 300 FSB, I refuse to lower my memory anymore and it doesn't even appear to help the OC any... I'm stuck at 3.9 for the time being... but I'm sure just like I was stuck at 3.64 before, some experimentation might cure this. As of right now though, I'm tempted to start toying with timings and other things. I can pull 22,800 in 3DMark 05, at the default test settings. Is this good, or bad (or about even for that matter)?

This is at 3.9Ghz, DDR2-1000 (5-5-5-15) and a Core 216 at 734/1476/1161


Anywhere, here are my settings:

NB Strap (Latch) = 200 (only 200 strap works)
Using 3.33C...

FSB = 300
PCI-E = 101

Vcore = 1.45
VTT = 1.1
PLL = 1.45
My REF voltages are close enough to 60% of VTT that's all i can recall.. +- about .010v

MCH is 1.2, and the rest is stock.

My Memory voltages are 2.080, and the rest of the associated voltages values are half of 2.080 so 1.040.

Memory Timings are set to 5-5-5-15, everything else is auto (As tight as I can get them).

That's probably spot on and it's the best I can recall while I'm here at work.

People always reccomend "LATCH=Auto" which is the same as strap I assume, and ideally that should be setting it to something that I can select manually. The best of my understanding is that it would be 4.00C, which would put my memory at 1200, well above what it can run, so no, it can't run at that. Simple suggestions aren't solving an obviously complicated problem. I tried every strap last night, nothing works but 2.66C at 345 (and below), 3.33C at 300 (and below), and 4.00C at 280~ and below...

I'd like to see something in the 3.9 area with 1120 memory and if I could only get 3.33C working that'd be possible but nooooooo... board and cpu don't like to place nice.

Specifically, does anybody know what I can do to make some of these straps work higher up in the FSB ranges? 3.33C at 300 would be simply amazing and would bring my memory around to where it should be.

Anything I haven't specified is at Auto. Tips, suggestions? Different bios? I'm running out of my own suggestions these days.

---

Aynjell (and everyone else asking for help!)
Put your system specs in your signature so we know what hardware you are running. Without that, we won't be much help.

Nevermind bluestang, if you need specs you're clearly in the wrong thread. this is about the UD3 P45 boards, and all the boards supported by this thread should have a similar system.

But to humor you... E5300 @ 3.9Ghz, UD3P, 8GB of RAM (same results with 2 dimms removed).

The rest is insignificant.

Quote:

---

Originally Posted by Aynjell

Nevermind bluestang, if you need specs you're clearly in the wrong thread. this is about the UD3 P45 boards, and all the boards supported by this thread should have a similar system.

But to humor you... E5300 @ 3.9Ghz, UD3P, 8GB of RAM (same results with 2 dimms removed).

The rest is insignificant.

---

I know I'm not the only one laughing at this!

Quads and Duals require different settings on these boards, as do 65nm and 45nm versions of them. Your processor and memory have alot to do with what you can accomplish.

If you don't want to listen to any of us when we ask for more info so that we can help you, then don't be surprised when no one helps you!

Quote:

---

Originally Posted by bluestang

I know I'm not the only one laughing at this!

Quads and Duals require different settings on these boards, as do 65nm and 45nm versions of them. Your processor and memory have alot to do with what you can accomplish.

If you don't want to listen to any of us when we ask for more info so that we can help you, then don't be surprised when no one helps you!

---

Second that

Quote:

---

Originally Posted by Ghostleader

Try the value that I have made in bold, it shouldn´t be far off.

---

Hey I used those settings you recommended and my pc was blue screening like mad. I had to raise the CPU Ref to 8.35, and MCH core to 1.37 to get into windows.

I immagine this question's been asked a bilion times, but what is the highest voltage you would put through these (q9550)?

CPU ref
MCH ref
CPU Core

I looked online and the answer is usually 1.3625 or something, but I see people putting 1.45 through these quads all the time...