What fans are you using? I would think with some of the more powerful ones you would need a 3rd PSU just for fans...
Printable View
What fans are you using? I would think with some of the more powerful ones you would need a 3rd PSU just for fans...
For now at least, you could just use 2 of the screws on each fan. A touch more stable with 4, but I've never once seen a problem with using only 2.Quote:
Originally Posted by Movieman
God that's hot.
Now I will have to peek at this thread everyday.
For how long? I don't know.:ROTF:
I have seriously though about transplanting the barrel fan out of a gas heater into a system case more than once.Quote:
Originally Posted by SAL36864
Interesting idea...Quote:
Originally Posted by D_A
Well being mains powered it puts no load on the PSU or motherboard, they move a MAL of air, AND if you do it right they run pretty damn quiet ... mounting might be tricky though.
Right now I have 5-120x25mm 113cfm Deltas in the front, 2 in the rear and planning 2 on each TRUE..Quote:
Originally Posted by SAL36864
0o0o0o so your planning a little thermalright tower town any plans for the chipset or pwm's?
The 560+cfm coming in the front across the board should handle that..Quote:
Originally Posted by =[PULSAR]=
Plus the wash from the 4 Deltas on the HS should handle things at the speeds I'll be at..
You would think, I used to have 1190+ CFM coming through the front of my MM case with 9 133cfm Ultra Kaze's :)
He should be just fine powering up the cards and fans off the antec :cool:Quote:
Originally Posted by SAL36864
back in a while. more to do..
If Movieman got the Extended Ascension (I it as an Ascension, but I can not tell if it is Extended) he could mount one (or rather place) on each side for a push pull configuration.Quote:
Originally Posted by D_A
You may want to go for 120x38mm fans. Should be quieter for the same amount of air moved. I while ago I went through and looked at all of the 120mm Delta fan manufacturer data, and what it made clear was that thicker is better.Quote:
Originally Posted by Movieman
Thats what she said:rofl::rofl::rofl:Quote:
Originally Posted by SAL36864
It's not the size of the wave, it's the motion of the ocean. :yepp:Quote:
Originally Posted by =[PULSAR]=
Though then again, bigger waves are more fun. :rofl:
And right now, Dave is cresting tsunami.
Pretty looking rig Dave. You must be beaming.
Looking like a pretty wicked rig. :up:
Bob
It's all assembled..
Just got to wire it up tomorrow and see what the baitch will do!:up:
Dude... I've spent last half hour reading all 16 pages and you still didn't make it work! Come oooooon :))))))))
Now I've seen it all. :)Quote:
Originally Posted by Movieman
I'd do a good old over kill for that case, one mo-ra2 rad to cases front panel and one to the top :p:
That would be some kooling power :D
But before this goes off topic too much: :slobber::slobber::slobber::slobber::slobber:
Ran into a little glitch at 2am, had to mount HS "sideways", then slept like the dead and last night here and now huge rain storm..Quote:
Originally Posted by LaMpiR
BUT the good news is the sleep gave me a solution that will get it the way I want it. Should fire it up in a few hours after I suck down some coffee and get human.:D
I read about the storm in newspapers, again 0,5 mil without electricity? Hows your generator doing? :)
We got lucky, didn't lose elec this time but generator is ready if we do..BUT..Quote:
Originally Posted by anubis
I don't think it's piddly 30 amp will power this rig!:rofl:
......searches ebay for 40kva generator to power this ftl machine :rofl: