Printable View
u guys got better bords than me.the bettter boards must be nwere like processors i gotta late week with cabyne y versionn 054 .this is a return from new egg but i own 3dmark 03 with it many options i tried em all .ch5 runs the best in here but overall neeed more volts erm or isuk
toook volcano 11 to get temps down.now 34c at load 10 x2.8 48 tops was 55
voltmod gives me 3.0 or 3.1 tops next is 5vmod wtf this board has gotta be the weirdest but fun.
i cant get this sukr runn ing with voltmod. i still get 1.9 .it runs better with my old speed preemium than geil pc 4000 ? gimmme a hand running bios 1.b
i do love the options to play with on this board.but i got higher 1 mil pi marks with hight 2 t timings than i do with low timings low titie pulling with this board .ermm please help or i just send back again
:nono:
Hi Guys, here's my setup
Athlon64 3200
MSI K8N Neo2 Platinum
2x512 OCZ DDR500 Gold VX
OCZ DDR Booster,
I can boot fine up to 260 HTT 1:1 @ 2.6Ghz. However, I can't seem to make it stable. Tried all combinations possible to no avail. Even at DDR400 I can't seem to find the right combination. Tried using dividers, different timings and voltage combinations. My OCZ Gold VX has been used previously on a DFI ultra-d and was rock solid stable. My proc and board used to have a corsair TCCD and was also stable.
Anyone here who has the same setup as I do and stable. Could you share your settings. Thanks
Quote:
Originally Posted by boygenius
Why dont you try some reality
10 x 250 venice 1.45 + 5% will be tring to turn this voltage down some
2 x 512 ocz rev 2 tccd 7 3 3 2.5 2.7 or 2.75
4 x 250 = perfect htt
sideffect bios for tccd
your 100 mhz off stabilty
If you got a 9 multi on your cpu I cant help you cause I dont think its worth going there.
chronodog
There's a post a few pages back about how voltage settings in bios don't reflect actual voltage after 1.8 because of the way they supported the newer cpu cores like san diego and X2. Basically you have to start from 1.4 (or 1.45?) and apply percentages. There was a helpful table or something to show what settings resulted in what actual voltages.
Dunno if that helps, but it might give you a starting point.
Hello all. First post here.
Just wanted to ask if anyone knows if the Ocz 2x1gig PC-4000EB 3,3,2,8 set works in this mobo ?
Right now the ram runs in my DFI ultra-d but can't use T1 as it fails Memtest, Test 8, But is stable at T2
Just want to know will this mobo like the ram enuff to run T1
performance, features, and overall balls, dont downgrade to the MSI keep the Ultra-D its not about the msi ro the ultra-D doing 1T its you overclocking too far.
The msi wont let you get near the stability nor clocking of the ultra-D
As much as i loved my msi i dont miss it one bit, the ultra-d just crushes it in every single way.
if you boot up at stock speeds and you cant do 1T then rma the ram its shot.
UNLESS the ram specifically says its 2T ram.
you need to be giving the ram more volts if you cant run 1T add another .5 onto the ram and see what it does.
what are you clocking the ram at right now anyways.
Everything in my system is stock. It's not the ram as it runs fine at T1 in my P4 system
After reading alot of posts on DFI street most people with 2gig of ram are needing to run at T2 to get it stable.
At T1 I can do 97pass's on Memtest with 7failed all in test 8
With 1 stick it pass's 99 runs @ T1 100% both sticks can do this. But to gether it fails T1
If you have a DFI nforce 4 then surely you have a pci express card and so moving back to AGP isnt really logical. Perhaps try another nforce 4 or even the radeon xpress.Quote:
Originally Posted by Kingsob
Kingsob Im runnng 2 x1 gb sticks 1t ddr500 or more fine. Make sure you have them in the slots closest to cpu and clear cmos. Right now Im doing a little prime heres a shot and still going.
SE hey mate, do you rely on any software for temp reading for our board? Yesterday my temp sensor went ballistic read 110 degrees. Now if it got that hot the cpu would have died right? Im worried Im going to get a spike in vcore and kill my cpu. This only happen when priming and right now my temps are reading real low.
Cpu z will jump from 1.5 to almost 1.6 sometimes also only when priming. I just dont know what to trust anymore. The BIOS vcore shoud be the ONLY ONE to trust right?/and all software readings for our board are false? The cpu temp in bios is not supposed to be accurate for alot of people but I think mine is fine? Sometimes I think the sensors read right with software but under stress they fold.
260X10 is prime stable with 1.5v, on to 2.7 prime. Will try 2.5-3-2-5 or 7 @246x11. 2.7 on air is the limit for me on this board/cpu and for alot of NF4 users:)
My full system specs are
AMD x2 4400+
OCZ5002048EBPE-K (OCZ Platinum EB PC4000 2GB Kit 3,3,2,8)
Asus 6800GT 256mb AGP (OC 400/1200)
DFI NF3 Ultra-D (Bios 7/11) Tryed 8/24 but still no good.
Audgiy 2 ZS
What about the chipset fan on these ? My DFI one died in 2 weeks. Also what's the best bios for a X2 ?
If the Bios doesn't support the X2 can I still use the the CPU to then flash or will the computer just not boot up at all ?
It should boot up showing only one core untill you flash to the latest bios supporting X2. If you have a dfi Nf3 board this is the neo2 thread so you will probably find more help in another thread.
Nice ram I was going to get some but I couldnt find it anywhere. :toast: The chipset fan on these are ok you might want to take it off and put some AS5 on it.
No No my friend is selling me his MSI. Got a nice deal on it. Was just asking if anyone has this ram and can do T1. If it can't then I may just leave the board out untill I get another CPU. But if I can use the ram at T1 I'll change over
When i try to put Core Centre on my motherboard it gives an error message of 'Your Motherboard does not support Core Centre'
Its an OEM motherboard manufactured by eveshamvale (reported by CPU-Z).
Cheers,
M
____
Your RAM will work fine at 1T with the MSI, as I'm sure your aware the BIOS on the DFI NF3 sucks and cause loads of problems, such as 1T cannot be selected.Quote:
Originally Posted by Kingsob
I suggest you test it first, but I'm sure it will work fine.
Just flash the latest MSI Neo2 BIOS on or one of Sideeffects BIOS's.Quote:
Originally Posted by noxidjkram
i wonder i mr. sideeffect could give me a little help :D
I'm using the notemp version of 1c3 cuz my 3000+ is under a mach2 gt
the problem is that I cant do high 1:1 fsb..
I have 350HTT stable! but I cant boot 3-4-4-8 1T 1:1 with mems...
another thing I've noticed is that A64 tweaker strats random settings so I cant define special ones for my 4800LA 2 * 512..
could anyone give me a little help?
sideeffect, will you release any bios version like tccd notemp? :)
there is no memory that can do 350mhz 1:1 ddr1 :|Quote:
Originally Posted by Elvas
max only +-320mhz with the best TCCD sticks.
and with the a64tweaker, with me it helps to refresh the program a couple of times when it shows wrong values
chipset fan is fine but gets very noisy after a while, but still functions fine.
Hi - i've got the latest MSI BIOS on - needed it to get my x2 processor recognised.Quote:
Originally Posted by Draxx
Any other ideas?
Cheers,
M
Anyone know if the ZM-NB47J will be good enough to passively cool my NB chipset?
I have no airflow in my case due to no fans (i'm watercooling). My PSU is a fanless Antec Phantom (which puts a bit of heat into the case).
Cheers,
M
does someone know whether this board supports opteron144 cpu's when you still have the first bios revision ?
second question :
will a ZM-NB47J cooler, cool my NB better than the stock chipset cooler ?
I didn't want to have a 350HTT mem on my board.. I just wanted them to work @ 300mhz just like gskill anounces..