Quote:
Originally Posted by mursaat
yes but when i apply voltage for my 3D profile, it's automatic applied for default profile so what am i doing wrong:S?
Printable View
Quote:
Originally Posted by mursaat
yes but when i apply voltage for my 3D profile, it's automatic applied for default profile so what am i doing wrong:S?
Rovtar, you can save the voltages to any profile you like from the page where you tune the voltages.
to default profile you can't :S
The Default profile is unchangeable, but as we said you have to make a 2nd profile AND save voltages. Applying doesn't save btw ;)
ATI Tool is a bit picky at first, you've got to:
make profile | settings | change values | apply | save | back | save profile | etc :D
ok now everything is fine (i haven't try css :D)
BTW a bit /OT, is there any way of getting css without steam? I hate that app since CS1.6 (first time Valve used it right?)
:D hmm look's like css is working fine ..(cpu was too oc)
mursaat :D no unless nonsteam but it's illegal .D
So far 711|810 on both cards with ATi Tool. Voltages 4.45|2.091|2.091|1.498. Stock air cooling. May be moving to water.
Since Crossfire runs async, if that is the limit of the master (711|810) I will simply keep moving up the XTX (Flashed XT). I haven't experimented enough with different voltage settings enough yet to say that is the master's limit for certain.
Nice ^^
but i have problems again.. i have tv tuner in one of the pci slots.. and when i run software(i have tried other software) which belongs to tv tuner computer freeze :S everything is working just fine (sound...) but my monitor draws yellow, blue.. screens and i have to restart
Hmmpfff.... AtiTool is giving me the finger... every time it crashes when I apply settings I know are good..
With the classic control panel and stock clocks I get 11928 on 05
With CCC, which is the only tool which let me OC without freezes, I get 12156 in 05 with 675/690 on the clocks simply because it's bloated beyond belief.. :slapass:
I agree about cat 6.4's - crappy overclockers compared to 6.3's, this is with ATItool being used. Have'nt tried the 6.5 beta's yet and won't till' official 6.5 release. :)Quote:
Originally Posted by nicepun
Hmm.. I'm using the 6.5 Beta... is that the source of AtiTool crashing on me when setting clocks or am I missing something...?
I hope you have better luck than I did Rovtar.Quote:
Originally Posted by Rovtar
My Theater 550 pro tv tuner card would not work in the ASUS boards I owned; the A8N premium SLi, or A8R MvP. I got the same lock ups you describe. The theater 550pro works great in this DFI board. It also worked in a EPoX 9NPA+SLi and Abit AT8 32X. Possibly something is up with ASUS.
Yes but this is strange because one week all worked perfectly but now... :S omg
Soon i will buy aopen and yonah and i hope everything will work just fine :D
my powercolor x1900xt comes aswell with BJ11 1,1ns
W1zzard hasn't touch ATiTool in a while since he's been somewhat busy with school and all. I don't think this issue is going to be resolved until he has time to sit down and rewrite the whole program from scratch, at least that's what he said.Quote:
Originally Posted by NightCrawlerâ„¢
Hi all, I'm new on here so just be gentle :toast: !
Ok i have big problem with my new Gigabyte x1900xtx!
I can't OC it! If i use AtiTool all goes wrong!
I did everithing mursaat said...
If i use that, there is no change between 2D/3D in 3/4 games or benches!Quote:
Originally Posted by mursaat
If i LOAD "3D" 700/830 (111xx ) and go to 3DM05 i get worse score than on default 650/775 (113xx) or everithing just freez! I hate ATItool :slapass:
And finally new RivaTuner is here :clap:
It works great. It clocks between 2D/3D (hardware monitoring) and OC higher (715/830 default voltage and stock cooling) than ATITool (700/830 default voltage and stock cooling)!
BUT, if i use 650/775 or 715/830 score is the "same" + - ! WTF?
What am i doing wrong?
I have...
TAGAN U15 480W 30A/2×20A
A64@2700MHz
2×512, 2 2 2 5, 1T
You not only have to Load the 3D profile, but go to settings -> 3D detection and set the 3D Profile to load when 3D app launches.
And yes, i did go to settings -> 3D detection and set the 3D Profile to load when 3D app launches.Quote:
Originally Posted by cole2109
BUT it didn't work!!!
WTF is wrong? I tried everithing! My OC 3DM05 score is 111xx! And i know this is low score, because one time (only one time) when i tested i got 11900, but never again!
Sapphire X1900XTX 1.425, 2.086, 2.086, 1.486 gives 684/801 Stock cooling with a 120mm 72CFM fan blowing over the back...
No matter what I try with more volts ( up to 1.575, 2.108, 2.108, 1.500 ) I don't get the clocks higher nor does my FPS/Score improve a single bit or 3DM05 just locks up at me...
Is this card a dud or am I missing something.. I see clocks way over 700 and this :banana::banana::banana::banana::banana: just won't go.. :slapass:
On stock volts i can go at last 730/1700. Have not tried higher. :)
This new riva tuner is damn good. :)
Not sure (as everyone) what does VDCCI do, but try to raise it, maybe that helps. I have a Sapphire XTX too and my max on stock cooler is 1.550/2.151/2.???/1.501 729/855 fan 100%. More speed or voltage makes the card freeze. I've ordered a vf900Cu. Only for the noise. I only hope temps are at least as low (or high :D) as with the stock cooler.
A more beefy PSU could help :)Quote:
Originally Posted by NightCrawlerâ„¢
Why....? It's got plenty of juice and enough amps on the 12v line...
I think the OCZ 520w is enough, it's single rail. For single X1900XTX should be OK. I would try raising the VDCCI first. It's cheaper too :DQuote:
Originally Posted by alpha0ne