i have 2x2gb 800mhz ddr2 memory its the corsair pro with the lights on it
I was wondering what peapole has been overclocking it to becuse when i overclock my q9450@3.5ghz it goes to 875mhz but i dont touch the latencies will it run for a few years or not or will it burn it out soner rather than later
thanks
Just sharing my latest template after a 24hr Prime Blend test (Slected custom and bumped RAM used up to 3200), the load temps are pretty stable at 54°C ą2°C with my new TrUE Black 120 installed. I am now considering trying to get the RAM down to 4-4-4-12 at this speed...
Code:*************************************
*************************************
Gigabyte GA-EP45-UD3P (Rev. 1.0) - F9
*************************************
*************************************
******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [Fast]
CPU Clock Ratio ......................: [9X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 4.10GHz( 456x9)
********** Clock Chip Control ********
>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [456]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]
>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]
******** DRAM Performance Control ********
Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: [Auto]
System Memory Multiplier (SPD)........: [2.00D]
Memory Frequency(Mhz).....800.........: 900
DRAM Timing Selectable (SPD)..........: [Manual]
>>>>> Standard Timing Control
x CAS Latency Time................5...: [ 5]
x tRCD ...........................5...: [ 4]
x tRP.............................5...: [ 4]
x tRAS...........................18...: [12]
>>>>> Advanced Timing Control.........: [Press Enter]
x tRRD............................3...: [ 4]
x tWTR............................3...: [ 4]
x tWR.............................6...: [ 8]
x tRFC...........................52...: [68]
x tRTP............................3...: [ 4]
x Command Rate (CMD) .............0...: [ 2]
>>>>> Channel A Timing Settings.......: [Press Enter]
x Static tRead Value.............11...: [ 9]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel A Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
>>>>> Channel B Timing Settings.......: [Press Enter]
x Static tRead Value.............11...: [ 9]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel B Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
****** Motherboard Voltage Control ******
Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Disabled]
CPU Vcore..............1.27500V.......: [1.30625V]
CPU Termination........1.200V.........: [1.280V]
CPU PLL................1.500V.........: [1.570V]
CPU Reference..........0.760V.........: [0.835V]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.200V]
MCH Reference..........0.760V.........: [0.778V]
MCH/DRAM Reference.....0.900V.........: [0.910V]
ICH I/O................1.500V.........: [1.590V]
ICH Core...............1.100V.........: [1.200V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.080V]
DRAM Termination.......0.900V.........: [Auto]
Channel A Reference....0.900V.........: [Auto]
Channel B Reference....0.900V.........: [Auto]
******** Advanced BIOS Features ********
Hard Disk Boot Priority...............: [Press Enter]
First Boot Device.....................: [USB-HDD]
Second Boot Device....................: [Hard Disk]
Third Boot Device.....................: [CDROM]
Password Check........................: [Setup]
HDD S.M.A.R.T. Capability.............: [Enabled]
Limit CPUID Max. to 3.................: [Disabled]
No-Execute Memory Protect.............: [Enabled]
CPU Enhanced Halt (C1E)...............: [Disabled]
C2/C2E State Support..................: [Disabled]
x C4/C4E State Support................: Disabled
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.....................: [Disabled]
Virtualization Technology.............: [Disabled]
Delay For HDD (Secs)..................: [ 0]
Full Screen LOGO Show.................: [Disabled]
Init Display First....................: [PEG]
******** Integrated Peripherals ********
USB Keyboard Function.................: [Enabled]
USB Mouse Function....................: [Enabled]
USB Storage Function..................: [Disabled]
h3x0r_1984,thanks for finding these post and giving us quick links.:D
good to see that you take the time and re-read through the thread.
i find myself doing at least every other day.:up:
again thanks.
also heres two more very informative post from lsdmeasap
http://www.xtremesystems.org/forums/...postcount=1157
http://www.xtremesystems.org/forums/...postcount=1023
Well this is waht I got... and... Im getting a bigger headache...
Those settings were stable at prime95 for 6hs, also It pases SuperPi 1m, 2m, 32m.Code:******Gigabyte EP45 UD3P******
Q9650 423 X 9 3800MHz
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ 0 ]
CPU Frequency 4.35GHz...........................[ 423 x 9 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 423 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 700mv ]
PCI Express Clock Drive.........................[ 700mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance [Standard]
Extreme Memory Profile (XMP)....................[ Disabled ]
(G) MCH Frequency Latch.........................[ 266MHz ]
System Memory Multipler.........................[ 2.50A ]
Memory Frequency 1066...........................[ 1058 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]
******Motherboard Voltage Control******
Load-Line Calibration [Disabled]
CPU Vcore [ 1.200 ]...................[ 1.37500 ]
CPU Termination [ 1.20 ]...................[ 1.260 ]
CPU PLL [ 1.50 ]...................[ 1.500 ]
CPU Reference [ 0.766 ]...................[ 0.853 ]
MCH Core [1.1 ]...................[ 1.240 ]
MCH Reference [0.760 ]...................[ 0.838 ]
MCH/DRAM Refernce [0.900 ]...................[ 1.050 ]
ICH I/O [1.500 ]...................[ 1.500]
ICH Core [1.100 ]...................[ 1.100]
DRAM Voltage [1.800 ]...................[ 2.10 ]
DRAM Termination [0.900 ]...................[ 1.050]
Channel A Ref [0.900 ]...................[ 1.050]
Channel B Ref [0.900 ]...................[ 1.050]
******Advanced BIOS Features******
CPU Multithreading..............................[ Disabled ] -----> I dotn know where is this one
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Enabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
But... there is some options which I dont know what they are like the ones on "advance clock control" and the options for MCH and the last ones for CPU, at the side of valtages.
But whatever, I will reed more, but I would like to know which ones for you should be the best settings to get 4ghz, that is what I want to begin :D
Thanks in advance.
try this and just see if it works.
http://www.xtremesystems.org/forums/...postcount=2070
You shouldn't need to change your clock drive voltage but sometimes 800/900mv can solve problems. Clock skews also help when doing high overclocks as some components especially the CPU and MCH will drift out of sync so adding a picosecond delay to it can work for fine tuning
Ok, so after reading over past threads and settings you guys (you know who you are!) suggested. I went back to F6 and after many boot attempts this is what I got tonight. It's a start. I'm not happy with my vcore though and PL9 needs to be lower. I think these will do PL7 with the right settings elsewhere! Tomorrow I will shoot for PL8 and 8.5 cpu multi for 4250.
BTW, I could not boot into XP succesfully until I lowered vdimm in BIOS from 2.30-2.36 (mfg suggested is 2.30-2.35) to the value below. Go figure, it wanted lower volts!
Any more suggestions is welcome and thanks again everyone!
http://img527.imageshack.us/img527/625/8x5001200pl9.jpg
Thanks, now Im testing 4ghz 9x 423.
The problem was an 8 on Performance level, thus I couldnt boot, but now I have a 9, and its running properly
Well I tried those settings and its boots properly but it wasnīt stable... thus I got BSOD.... aaaaaaaaaaaaaaaaaand it is getting up my nerves.Quote:
Originally Posted by radaja
I think the problem could be the ram, dispite (to my way of thinking) the high VID I have, which is 1.25000 and maybe I need more vcore... but with 1.4000 set on bios it wasn't stable.
So what you think ?
Osterman, I have a 1.25vid q9650 also. I put it back in tonight to mess with. Have not run Prime yet but ran LinX and passed with these settings. You could also try the 2.00D PL9 if you are unsure about your ram.
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 9
CPU Frequency .........................: 4.20GHz (467X9)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 467
PCI Express Frequency (Mhz) ...........: 100
C.I.A.2 ...............................: [Disabled]
Advanced Clock Control
CPU Clock Drive........................: 800mV
PCI Express Clock Drive................: 900mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)....................: 0ps
DRAM Performance Control
Performance Enhance....................:Standard
Extreme Memory Profile (X.M.P.)........: Disabled
(G)MCH Frequency Latch.................: Auto
System Memory Multiplier ..............: 2.40b
Memory Frequency (Mhz) ................: 1121MHz
Standard Timing Control
CAS Latency Time.......................: 5
tRCD ..................................: 5
tRP'...................................: 5
tRAS...................................: 15
PL8
Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enabled]
CPU Vcore..............................: 1.35625v
CPU Termination........................: 1.30v
CPU PLL................................: 1.45v
CPU Reference..........................:0.848
MCH/ICH
MCH Core...............................: 1.320v
Reference..............................:0.863
MCH/DRAM Ref...........................: Normal
ICH I/O................................: Normal
ICH Core...............................: Normal
DRAM
DRAM Voltage...........................: 2.10 (whatever your ram is rated)
DRAM Termination ......................: Normal
Channel A Reference....................: Normal
Channel B Reference ...................: Normal
hey guys, i know some variant of this question's been asked various times over here, but are the ud3r boards still neglected for bios updates? Last i read, UD3P is up to F9l but what about the UD3R? Seems like most people agree the UD3R clocks as well as the UD3P, which is really the main concern of mine; i don't need crossfire and all the extras UD3P has got to offer, so going for the UD3R should be a better ($$$) choice i hope?
Both the UD3P and UD3R are official at F9 (with the same bios change description) so there itīs no different, the F9l for the UD3P is not official.Quote:
Originally Posted by noinimod
Some say that UD3P have higher priority then the UD3R when it comes down to bios fix but I doubt that.
UD3R is good choice if donīt want the extra bling bling.
this is my first time running linpack on my Q9550+EP45T-UD3R
(thanks to Dua|ist for this LinX program)
http://img34.imageshack.us/img34/835...0520195527.png
CPU's temp/voltages info... at before running LinX
http://img195.imageshack.us/img195/1...0184800.th.png
http://img188.imageshack.us/img188/8...0184821.th.png
CPU's temp/voltages... during running LinX
http://img35.imageshack.us/img35/245...0190908.th.png
http://img34.imageshack.us/img34/391...0190953.th.png
and then i shutdown the computer and restart it, and rerun LinX...
http://img193.imageshack.us/img193/6...0520224452.png
rest of the bios settings were 800/900/0/0, Turbo, Strap 333, DDR3-1600, 7-7-7-20-auto's, DDR3 Write Levelling/Write Training: Disabled
@pangingIII
Nice work :up:
LinX is a nice app isnīt.
Whatīs up with the different in time and GFlops between the runs ~42 GFlops compare to ~60 GFlops, same core speed, bus speed, ram speed, timing, problem size and memory use. :confused:
Hi Ghostleader,
i probably had something running at the time? or something? i'm really not sure what was causing them to be like that.
here's another one that i ran it at 4.0GHz
http://img43.imageshack.us/img43/734...0520154217.png
CPU's temp during running LinX.
the room was kinda warm, no air con at the time that i ran this test.
http://img35.imageshack.us/img35/816...0150619.th.png
I know, it can really get hot with LinX, need to have good cooling. What kind of cooling do you have on that quad.
True Ex with 2 fans.
my system is usually using in an air-con room so the core temp usually never got that high,
if it has to be in full load more often than it is now i'll consider improving the core temp, i think.
Ghostleader, how old are those Hyperx PC2-9600's in you sig? Just curious as I just got some PC2-9200 from Newegg.
bluestang post some results with that memory and tell us if they are D9. I think u are getting 2x1GB sticks.Quote:
Originally Posted by bluestang
kagula23, will do as soon soon as I can get 500fsbx8.5 stable. I already have them installed since the weekend. I haven't taken off the heatspreaders though to look at the chips. I think the are Elpida though, not D9. I'm afraid to try and take off heatspreaders!!Quote:
Originally Posted by kagula323
Well I tried a couple of things.
And I still getting BSOD, voltages... I dont think so, I think the problem are ram.
Could you people tell me which settings did you use for 2x2gb 1066mhz (that is what I have).
By the way, I can get stability with 3.8 423x9, but I cant have it with 4ghz (450x9= 4.05, 445x9= 4ghz, 471x8.5= 4ghz, 500x8=4ghz) I CANT!!!!! AND IT'S DISTRUBING jaja.
Thanks.!
Osterman, I have 2 sets of this http://www.newegg.com/Product/Produc...82E16820231246 Both sets do at least 1130mhz 2.10v, PL8. I think it has to be settings, most all of these cpu's will do over 4.0ghz. Have you tried dropping the CPU multi and just testing ram to see what it will do? That will give you a better idea what the problem may be.
I have 1 set of this http://www.newegg.com/Product/Produc...82E16820231166
And those settings you have are for 24/7??
I bought two set of 2x1 in november 2007 and they are Micron D9GKX and they got really hot with the original heatspreader, did a 100% stresstest (HCI design Memtest) @ 1200 555 15 2.30V) and placed a temp sensor inside and got a temp ~65C, not good I thought.Quote:
Originally Posted by bluestang
Placed 2 60 fans@1700rpm (donīt like noice, therefore not higher) above the ram and got a temp ~55C, not good either.
I bought myself some Nexus Heat Pipe Memory Cooler (looks like OCZīs Reaper) and replaced the original heatspreaders, same kind of stresstest and got a temp ~40 without fan, I have not tested with fans because Iīm pleased with that temp, my ambient room temp was ~21.
Removing the heatspreader was rather easy, have to be careful though, I did the same to a set of 4x1 Kingston HuperX PC8500 (Elpida IC) no problem there either but when I tried it on a set of OCZ Titanium Alpha VX2 the IC came lose, tough luck but thatīs the way itīs some time.
http://www.nexustechnologyusa.com/nt...hxr-5500bl.jpg
i rerun LinX after changing a few bios settings for my q9550 at 4.0GHz
http://img34.imageshack.us/img34/172...0521200219.png
btw, Ghostleader, what's wrong with your UD3P?