All seems OK on my system.
Flashed to 1004 this morning....no issues to report.
Printable View
All seems OK on my system.
Flashed to 1004 this morning....no issues to report.
I've been waiting 4 a new bios.
I'll give this a try and tell you guys how it goes.
Please ineedaname! do it!
How come you have your E6600 at 3.6ghz at 1.37500!!!!!!!!!!!!!!!!!!!!!!!!!!!! :(:(:(:(:(:(:(
is my board a pre-release one? or what? or is it my CPU? L628A cant believe is that BAd! I dont relaly know whats causing my problems GRRR
at 333mhz I need 1.34vcore, it ran orthos for 8 hours but then... nightmare begins at 345mhz and up
Where's the difference between the
ASUS Striker Extreme
mfg > (90-MIB140-G0EAY00T) &
mfg >(90-MBB5X0-G0EAY00Z)
don't know which one to buy.
hi , where do you find those numbers?Quote:
Originally Posted by mutang
There you goQuote:
Originally Posted by andyr(uk)
http://geizhals.at/eu/?fs=asus+striker&in=
It's the only site that has the mfg listed.
It might be a good idea to email them and ask if this is the "so-wanted" 1.03 revision.
Hi , looked through those sites and cant read German very well , so whats the difference apart from 30 euros
IIRC,Quote:
Originally Posted by mutang
00Z is China
00T is Taiwan
Once again, I don't know for sure. People with Taiwan boards check their boxes, my China board says 00Z.
Mines says Made in Taiwan but where do I look that 90-MIB....?
Mines is 1.00G bought in newegg at january 20
Hi , my board says rev 1.00G and is made in Taiwan and part number on box is 90-MIB140-GOEAY00T
OK so i tried out this new bios and as far as I can tell its pretty much the exact same as the 1002 bios. At this point i just feel like they just renamed the 1002 beta bios and called it official. I haven't been able to clock my ram any higher at all. As for the cpu it seems pretty much the same I can't get my voltages any lower.
After a bit more testing it seems like it might even be less stable but the difference is negligible.
Nice Thread :) I've the same setup, and been enjoying clocking it... i'll take your advices eva2000 in order to improve my performance ;)
Thanks
I wrote an email.. here's the reply.Quote:
Originally Posted by slim142
Quote:
Both Mainboards Asus Striker (sound, 2x G-LAN, SATA II RAID); Art. No.: GPEA69 and Asus Striker extreme (sound, 2x G-LAN, SATA II RAID); Art. No.: GPEA68 differ merely in 2x eSATA controller which the extreme variation owns more.
Hmmmmmmmmmmmmmmm
Just to clear this up a little bit....Quote:
Originally Posted by Lood007
Taiwan manufacturing number is 90-MIB140-G0EAY00T
China manufacturing number is 90-MIB140-G0AAY00Z
Quote:
Originally Posted by wikked
So, which one is better? Taiwan or China??:)
probably taiwan but i haven't seen any proof as to whether one is better than the other
eva
you think a better OC can be achieved by putting some good cooling on the NB?
well it gets hot even at stock speeds , imagine pumping 1.6 volts through it, a good fan placed nearby will help OC surely and stability in general... Mien wouldn't boot at 500mhz from Bios with the stock heatpipe and a fan, now with the watercooling 500mhz is no issue, sadly cannot get it stable as I damaged the board a bit when modding my case... ( dam plier fell onto it, I'm glad it still boots lol max FSB now is 395Mhz )
Need some advice about OC of this board and let me show what I have:
-Striker
-CPU Cooller
-E6600
-1 x nVIDIA 8800GTX
-2 x 1GB = 2GB RAM
How to configure stable OC for these?
ThanQ
If the NB is hampering oc's then yes, if not then probably won't change much.. only way to know is try it for yourself :)Quote:
Originally Posted by slim142
And there's no special procedure for removing the stock heatpipes
Well yeah I just did, putted some HR-05 in both SB and NB and MC14 on VRM and overclock improved 10% but still not enough.
I think my RAM is holding me back so what I did was I bought yesterday the G.Skill HZ 2Gb DDR800 pack (the ones with black spreaders like you used on your review) to see if I can get higher overclocking results.
I just hope they arrive with some good D9GMH.
BTW, Eva, how good do the G.Skill sticks respond when using them with the striker? do they like each other? :) I might buy another pack soon to have 4Gb of RAM.
i'm just letting you know that my g.skill 800hz didn't respond well to voltage at all. Could be possible its not the ram and maybe just the chipset or something but running at certain speeds i would get more errors the more voltage i put to them. Seems like there were a few other ppl on the forums who noticed that too. about 2.3v seemed to be the sweet spot.
Could be possible that the heat spreaders were preventing any further heat from getting dissipated. I haven't tried removing my heat spreaders but its also possible that i have GCT and not GMH.
well if u guys haven't seen it already some guy's saying there's a 1102 bios.
http://www.xtremesystems.org/forums/...d.php?t=139966