yep very common on these boards.comes from the PWM area under load w/OCed.some people exchange thier boards only to have it do it on the new one too.
i've never noticed it on my three boards but my fans would be too loud anyways.most likely they all do it.like hoss331 said,i wouldnt worry too much about it.
I've gone back to the F5 bios for the UD3P, and S3 works properly again. I know for certain it wasn't working in F8 or F9. No change in overclocking capabilities it seems.
got my cpu today and fired up the UD3R all good!cant do much OCing as its a low vid chip and i only have the stock heatsink.i have a mini-typhoon with a 92mm/38mm 4000rpm fan mounted on it but it just will not snap down.
New run on the 9650.
http://i131.photobucket.com/albums/p...Untitled1a.jpg
Does the UD3P drops VCore and Multiplier (to 6x) when C1E/EIST is enabled in the bios?
Yep
ok i have notest thay my q9450 @2.66ghz gives me no better results even at 3.5ghz im getting 17245 in 3d mark 06 instead of 13314 but in fallout 3 im getting 50fps no matter what i do with overclocking v-sink is disabled so i dont know why its happining
Has anyone got any ideas why this is happining or is it just me been a idiot and not doing something
thanks guys
im so gelous on the overclocks your getting wish i had the balls to push my rig that far
sorry for spelling
I had 9450@3.92 on water, vCore 1.525. UD3P can more than 3.5GHz.
mine is on air but did you notace a difference in fps in gamesQuote:
Originally Posted by Loco23
Thanks.Quote:
Originally Posted by Hoss331
Nice Q9650 you have there. What batch#?
This my stable settings:
Code:MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .................: Auto
CPU Clock Ratio .........................: 8x
Fine CPU Clock Ratio.....................: +0.0
CPU Frequency ...........................: 3.92GHz (490x8)
********** Clock Chip Control ************
>>>>> Standard Clock Control
CPU Host Clock Control...................: Enabled
CPU Host Frequency (Mhz) ................: 490Mhz
PCI Express Frequency (Mhz) .............: 100
C.I.A.2 .................................: Disabled
>>>>> Advanced Clock Control [Press Enter]
CPU Clock Drive..........................: 800mV
PCI Express Clock Drive..................: 900mV
CPU Clock Skew (ps)......................: 0ps
MCH Clock Skew (ps)......................: 0ps
********** DRAM Performance Control ******
Performance Enhance......................: Turbo]
Extreme Memory Profile (X.M.P.)..........: Disabled
(G)MCH Frequency Latch...................: 333
System Memory Multiplier ................: 2.40B
Memory Frequency (Mhz) ..................: 1176
DRAM Timing Selectable ..................: Manual
Standard Timing Control
CAS Latency Time.........................: 5
tRCD ....................................: 5
tRP'.....................................: 5
tRAS.....................................: 15
>>>>> Advanced Timing Control [Press Enter]
>>>>> Channel A Timing Settings [Press Enter]
Static tRead Value.......................: 8
>>>>> Channel B Timing Settings [Press Enter]
Static tRead Value.......................: 8
********** Motherboard Voltage Control ***
>>>>> CPU
CPU Vcore................................: 1.525 change this for your CPU
CPU Termination..........................: 1.36
CPU PLL..................................: 1.57
CPU Reference............................: 0.901
>>>>> MCH/ICH
MCH Core.................................: 1.36
MCH Reference............................: 0.863
MCH/DRAM Reference.......................: Auto
ICH I/O..................................: 1.5
ICH Core.................................: 1.1
>>>>> DRAM
DRAM Voltage.............................: 2.18 change this for your RAM
DRAM Termination.........................: Auto
Channel A Reference......................: Auto
Channel B Reference......................: Auto
Advanced Settings
Limit CPUID Max. to 3....................: Disabled
No-Execute Memory Protect................: Enabled
CPU Enhanced Halt (C1E)..................: Disabled
C2/C2E State Support.....................: Disabled
C4/C4E State Support.....................: Disabled
CPU Thermal Monitor 2(TM2) ..............: Enabled
CPU EIST Function........................: Disabled
Virtualization Technology................: Disabled
I don't know, did't do any tests.Quote:
Originally Posted by rubber5
Alright overclocking experts...I'm trying to get my system at 8.5x500 FSB with 2.40B RAM multi for 1200 MHZ. After I adjust settings in BIOS (or ET6 after boot), what are the first tests I should run? Prime small, large or blend? Or 32m Pi run? Or memtest from USB key? Also, what failures mean what in specific tests when it happens quickly or after testing a while? I think this info would help everyone out instead of just trying to jump into a Prime blend for 8+ hours. Thanks!!!
batch is L827A945, 1.15VID :up:Quote:
Originally Posted by Jupiler
@ Ghostleader ... how is the Rampage Formula with Dual Cores in overclocking?
What about E8500 FPO:Q828A339? does anyone have it? it's E0? please post u'r results ... if u have the same fpo or fpo q828 on your E8500
8GB (4x2GB) RAM - EP45T-UD3R - Q9550
http://img25.imageshack.us/img25/465...0514193911.png
http://img25.imageshack.us/img25/866...0514202411.png
Anyone have UD3R on F9 BIOS running 500fsb x 8 or 8.5 with 2.4B mem latch for 2x1GB sticks? I can't get it to post....it tries twice, each with multiples beeps, then resets to default. I was running this setup (500x8 or 525x8) fine before with 2.0B or 2.0D for 1:1 ram with 2x2GB Dominators. But I since bought a Kingston HyperX DDR2-1150 2x1GB kit and want to run 2.4B for 1200mhz. Or am I better off running 450fsb with 2.66D? Any ideas or suggestions?
New BIOS:
GA-EP45-UD3P - F9l
Released 08.05.09
Thanks!Quote:
Originally Posted by stasio
Any changes known? Changelog?
I just had the most amazingly simple overclock with the ep45ud3p and an e8500. I finished setting up a friends rig and only had a little time left so I bumped the voltage on his 8500 to 3.7 and bumped the fsb to a nice round number and BANG! a stable 4.08ghz right off the bat.
What a sweet motherboard.
EDIT Sorry I meant 1.37.
If you set your friends' core voltage to 3.7 volts then it's surprising his CPU didn't go BANG!!!Quote:
Originally Posted by HeXploiT
:shocked: :rofl:Quote:
Originally Posted by unclewebb
sorry to ask again but no one has sed if there getting more frames when thay overclock
like i sed i have a q9450@2.6 and no change in games even when i go to 3.5ghz
i have a gtx280 (no oc) but nothing gives me more frames is it just the 280 cant handle anymore frames or is is something im doing wrong
PLEASE HELP ME
thanks
ps SWEET overclocks im seeing i wish i had the mony to get better frames in my games (sli) :)
The best thing to do would be overclock your GTX 280. Use EVGA Precision to do the overclocking and use Furmark to test stability.Quote:
Originally Posted by rubber5