ABIT IC7 – IC7-G – IC7 MAX3 ALL in one Modifications - The way to go!

Ok, I have stayed up all night doing mods and I have only done 2 mods so far! Man, I'm slow. But hopefully I will finish in a day or two and I will post some photo's of my xtreme max3 :D

Hello

There is a modded BIOS 26 for IC7 here for those who are interested.

Regards,
pokipoki

Quote:

---

Originally Posted by hipro5

U P D A T E


In case that someone needs the VCore mod.......Here it is.......

Just solder a 100 KOhms trimer at this spot to ground...... ;)

http://www.thelab.gr/images/Hipro5/T...d_ABIT_IC7.jpg


GROUND is the one side of the MC371 where one cable is soldered and the other spot is the THIRD spot from the IC and to com and serial ports side (not the CPU side) of the mobo......There's a missing resistor there.... ;)

---

Hello Hypro and everybody else, I am new to these forums although I know some of you well from other forums.

I have the following droop problem on an IC7MAX3 with P4 3.2E (SL7CK) @ 4010 MHz, Using twin PSU's, one only for mobo ATX cons(Enermax 465W with 33A 12V rails:

My chip need 1.52-1.54V Vcore under load to run stable at this speed. In order to reach this minimum I have to set Vcore in bios to 1.58. The droop on the 12V ATX con is only 12.17 - 12.08. Will this mod help stabilize towards idle=load? Also, does this mod work on my mobo?

Thank you for answering. I use various mods from yr great guide, under which the Vcore caps mod, and the 12V xtra input choke mod.

Quote:

---

Originally Posted by woutertal

Hello Hypro and everybody else, I am new to these forums although I know some of you well from other forums.

I have the following droop problem on an IC7MAX3 with P4 3.2E (SL7CK) @ 4010 MHz, Using twin PSU's, one only for mobo ATX cons(Enermax 465W with 33A 12V rails:

My chip need 1.52-1.54V Vcore under load to run stable at this speed. In order to reach this minimum I have to set Vcore in bios to 1.58. The droop on the 12V ATX con is only 12.17 - 12.08. Will this mod help stabilize towards idle=load? Also, does this mod work on my mobo?

Thank you for answering. I use various mods from yr great guide, under which the Vcore caps mod, and the 12V xtra input choke mod.

---

This mod is only if you want to get higher VCore than the Mobo can supply.....I don't think though that you accualy have VCore droop problems as for IC7 series mobos......Measuring with a multimeter is the best to find out that...... ;)

Quote:

---

Originally Posted by hipro5

This mod is only if you want to get higher VCore than the Mobo can supply.....I don't think though that you accualy have VCore droop problems as for IC7 series mobos......Measuring with a multimeter is the best to find out that...... ;)

---

I know, I always measure everything with a DMM, even the temps. Now, The droop I am writing about is actual droop, measured with DMM. Sorry I forgot to mention that. I already got rid of 0.12 droop that I had on my ATX cable, by replacing it with a higher gauge type cable. The droop is measured accross the extra caps soldered on the back of my board. They actually helped reduce droop a little.

i have done 3 mods on my max 3 agp ,vtt and vdd
they all work but that does not mean am getting more mhz out of it
so for the only mod that did wonders for me was the vtt mod
agp and vdd didn't help me at all
i have to say i only tested the board on air so far
gonna slap the prom on this weekend and see how far i can get
i also wanna do the capacitor mod but havent found the right capacitor yet

il keep u guys updated how she does under the prom

Quote:

---

Originally Posted by hipro5

1.You unsolder THE R50 resistor......and solder on it's place a 10Ohms one
2.Yes.....
3.Yes........
4.Yes.....
You have t trimm it at maximum value(200Ohms) and then start playing around........IF you trimm it at 0Ohms and leave it there , your mobo will NOT boot at all.........

---

i think this might be my problem then.i got a friend to do all the mods.tried starting and nothing.its like the psu fans try to start but no go.which trimmer du i have to adjust?the vtt or ?hopefully the board aint dead.

Quote:

---

Originally Posted by hipro5

I know...........I've lost AND repaired :D my other 24/7 Air cooled rig for SETI with a Prescott 3GHz at 3500MHz......Two tiny Mos-Fets went down......Of caurce I have about 3 burned down IC7's and I replaced the Mos-Fets of it and now I'm OK......A Max3 one have ALSO gone down with a Prescott 3.2GHz..........Heatsinks and air on the tiny VCore Mos-Fets...... ;)

---

which mosfets went down.thats what happenned to me testing a 3.2e@3.8 with prime.would appriciat a photo of there location.i let it run overnight and next morning the comp was off.tried restarting but it couldnt.any clues to what happened.tried testing all the other hw and they work.i thought it was the ram mod that did it.couse im not so good in soldering.and as soon as i tried touching the wire on the mod it came off.so i sent it to a guy who fixed the mod and put all the other mods on while he was at it.got it back tried to boot and nothing. :( like the psu tries to start but fails.please help

can u mesure agp voltage with multimeter? try not to go above 1.95v
make sure the trace cut for agp mod is done right , my board was behaving strange because cut wasn't done properly
check this with multimeter to be sure

ill have to buy a multi meter,thanks

Hi guys!
I'm gonna do the vcore stablization mod just after doing the vdimm mod. I cannot solder the capacitor's on the back of my IC7 because i would not be able to put it back to my case. My friend told me to do it another way but i'm not sure if he is right. Please check this out :)
The whole thing is about unsoldering one of the capacitors from the mobo and connect some extra like this www.gorajec.net/Adasi/mod_eng.jpg .

cut a hole in the case so it will fit

Yes i know that's the easiest way but the reason i want to do it another way is that i don't want to cut my case again :(

hi, I did the VTT mod but not tested yet.
I have a question... how can I verify that the trace is successfully cut?
thx

any clues to #284

Quote:

---

Originally Posted by vanovich

which mosfets went down.thats what happenned to me testing a 3.2e@3.8 with prime.would appriciat a photo of there location.i let it run overnight and next morning the comp was off.tried restarting but it couldnt.any clues to what happened.tried testing all the other hw and they work.i thought it was the ram mod that did it.couse im not so good in soldering.and as soon as i tried touching the wire on the mod it came off.so i sent it to a guy who fixed the mod and put all the other mods on while he was at it.got it back tried to boot and nothing. :( like the psu tries to start but fails.please help

---

Where burned the two SMALL Mos-Fets - drivers - of the big ones for the VCore near the socket.......There are four small and four big ones for it......

Quote:

---

Originally Posted by potkit

hi, I did the VTT mod but not tested yet.
I have a question... how can I verify that the trace is successfully cut?
thx

---

You can verify that the trace is cut by measuring from the two Mos-Fets - the ones that we measure the VTT - to the Capacitor of the picture I've posted........You sould measure NO contact......If you measure 0 Ohms then retry to do it...... ;)

i have done vtt mod ,agp mod and vdd mod and i dont seen to get the system stable over 265 fsb am using a 3.0c mach 2 cooled vdd set @ anything above 1.6v results in a worse oc vapg mod didnt seem to help me ,vtt helps me to get my b5 over 240fsb 1:1 @ 3.2v am using 2x512 sticks mushkin lv 2
@ 265-270 fsb am able to boot into windows but after a few minutes screen goes black aand computer reboots whatcould the problem be?
my 3.0c maxing out @ around 4000mhz????

Quote:

---

Originally Posted by hipro5

You can verify that the trace is cut by measuring from the two Mos-Fets - the ones that we measure the VTT - to the Capacitor of the picture I've posted........You sould measure NO contact......If you measure 0 Ohms then retry to do it...... ;)

---

ok so i've to measure here:
http://www.sk8hack.com.mx/20.jpg
and... what capacitor?

thx for your time :)

Quote:

---

Originally Posted by potkit

ok so i've to measure here:
and... what capacitor?

thx for your time :)

---

Yes..........and on those spots

Here.......

http://www.thelab.gr/images/reviews/...VTT/VTT_21.jpg

...........and here........

http://www.thelab.gr/images/reviews/.../VTT/VTT_8.jpg


..........after the cuting you should measure at those two spots NO conectivity..........NOT 0 Ohms......

Quote:

---

Originally Posted by blowsion

i have done vtt mod ,agp mod and vdd mod and i dont seen to get the system stable over 265 fsb am using a 3.0c mach 2 cooled vdd set @ anything above 1.6v results in a worse oc vapg mod didnt seem to help me ,vtt helps me to get my b5 over 240fsb 1:1 @ 3.2v am using 2x512 sticks mushkin lv 2
@ 265-270 fsb am able to boot into windows but after a few minutes screen goes black aand computer reboots whatcould the problem be?
my 3.0c maxing out @ around 4000mhz????

---

Try to max your VAGP at - let's say - 1.8VAGP - and put into bios those settings for BH-5 , BH-6 chips........ ;)

2 - 5 - 2 - 2 32M Auto(not too aggressive) Enhanced 5 (or 4 - more aggressive , you HAVE to put it 5 in case of 5:4) Enable and Enable(this last try it at disable as well).......

I do the Malve's mod... but i've a question...
look at the picture
http://www.sk8hack.com.mx/2.JPG
is that correct?
now... the guide says that i've to put a 200ohms vr at 0 ohms ....
but what pin is ground? the #1?
i've to put the vr at 0ohms... but betwen what pins?
between #3 and #1 or between #2 an #1

thx again :)

Quote:

---

Originally Posted by potkit

I do the Malve's mod... but i've a question...
look at the picture
is that correct?
now... the guide says that i've to put a 200ohms vr at 0 ohms ....
but what pin is ground? the #1?
i've to put the vr at 0ohms... but betwen what pins?
between #3 and #1 or between #2 an #1

thx again :)

---

0 Ohms at pin 1 and pin 2.........I hope that you have already cut the VTT trace though...... ;)

Quote:

---

Originally Posted by vanovich

any clues to #284

---

now if the vdd mod was to be taken off.would the mb still boot?which way do i have to turn the trimmers if i wanted everthing as standard (no volt rises)i ask couse maybe i can determen if the mb will boot at all.i have 5 trimmers at the time being and hopefully they are set wrong,cousing the mb not to boot. :confused: im also tring to determind if i burnt any of the mosfets!

Quote:

---

Originally Posted by vanovich

now if the vdd mod was to be taken off.would the mb still boot?which way do i have to turn the trimmers if i wanted everthing as standard (no volt rises)i ask couse maybe i can determen if the mb will boot at all.i have 5 trimmers at the time being and hopefully they are set wrong,cousing the mb not to boot. :confused: im also tring to determind if i burnt any of the mosfets!

---

Try to turn them from the GROUND to every spot of them at their maximux resistance..........Also try to remeasure the resistance between cutings......You should see the 10 Ohms resistor..........IF not try to resolder it again.........