EP45-UD3P

Printable View

Show 100 post(s) from this thread on one page

03-24-2009, 11:16 AM
Ghostleader

Quote:

Originally Posted by Bootup05

Can someone get me a link to where to measure with a DMM for vcore on the UD3P :)

I've had a google but it didn't bring anything up, and this thread is a bit too long to browse through! :p:

Thanks..

Here you go

http://images.hardwarecanucks.com/im...eadpoints4.jpg

hardwarecanucks.com Gigabyte GA-EP45-UD3P P45 Motherboard Review
03-24-2009, 01:41 PM
darthvedor

Hi all,

I need advise, i´m trying to reach 4500Mhz prime stable with this config but I only can get stable at 4400.
Can some one help.

http://img.techpowerup.org/090324/Capture001925.jpg

Thanks
03-24-2009, 03:24 PM
bt_medic04

how well does the EP45 UD3R overclock quads compared to the EP45 UD3P? does the UD3R have the same bios options as the UD3P?
03-24-2009, 03:37 PM
OC Nub

1 Attachment(s)

q9650

I'm officially retiring my q9650 from anymore testing. This is as Xtreme as I care to get with the temps :shocked:. This was at 1.3875vcore set in bios. Also, cannot get LinX to read the same MAX memory any two times I open it. Close everything out before opening it and selecting ALL. Runs great at 4.14ghz so Ill keep it there.
03-24-2009, 04:15 PM
wfarid

nice clocks jor
03-24-2009, 04:24 PM
xEnergie

My BIOS cpu vcore is set to 1.26 and in windows cpuz is reporting 1.216. Is that variance considered acceptable?
03-24-2009, 05:59 PM
OC Nub

1 Attachment(s)

Ok maybe a few more tests

Was able to get the Vcore down and also MCH :D. Temps were a few c better, max was 72c. Have not primed it with these voltages yet, may try that tonight.
03-24-2009, 06:03 PM
XpuctoC.

xEnergie, it is OK if it doesn't lead to instability, however you would better set "Load-Line Calibration" to "Enabled" in the BIOS, if you want to overclock - and you will get rid of the vDrop this way.
03-24-2009, 10:12 PM
Ghostleader

Quote:

Originally Posted by darthvedor

Hi all,

I need advise, i´m trying to reach 4500Mhz prime stable with this config but I only can get stable at 4400.
Can some one help.

Thanks

What about more vcore?

Btw, what hardware config do you run?
It´s easier for us to help if we know that, "Edit signature" under "User CP".
03-25-2009, 01:10 AM
Hardc0r3

Quote:

Originally Posted by xEnergie

My BIOS cpu vcore is set to 1.26 and in windows cpuz is reporting 1.216. Is that variance considered acceptable?

i dont know but my board ud3p rev 1.0 is dropping like hell 2 , so i enabled llc and on idle and under load 1.25 is reported 1.232 which is fine with me.
03-25-2009, 03:52 AM
SiliconManC

Hi

I've just got the ep45-ud3p rev. 1.0 to replace my abit ip35 pro and I am having problems with overclocking my Q9550 (L837B542). The problem is that I can't overclock at ALL. Even if I set the fsb to 340 the board don't boot. With abit I was at 8.5*435=3.7GHz with 1,23vcore mch 1,44, mem@1044MHz with 5-5-5-15 everything else was at default. Any suggestions?

My specs is:

Q9550 (L837B542)
ep45-ud3p rev. 1.0 bios f9b
2x2GB Crucial Ballistix 800MHz (BL2564AA80A)@modded Corsair Airflow
sapphire ati 3870
enermax infinity 650W

WC
silverprop cyclone ve
swiftech mcw60
bixII with 2 coolermaster led fans
eheim 1250
t-line
03-25-2009, 06:37 AM
darthvedor

Quote:

Originally Posted by Ghostleader

What about more vcore?

Btw, what hardware config do you run?
It´s easier for us to help if we know that, "Edit signature" under "User CP".

Hi,

The Hardware is:

Intel E8600 E0
Cellshock PC3-14400 (DDR3-1800) 2GB DDR3 Kit
Sapphire ATI Radeon HD 4870 512MB GDDR5
Corsair HX620
Cpu cool by Tuniq Tower 120

is safe to give more cpu vcore on air?

Thks
03-25-2009, 07:18 AM
andressergio

from MF2 raid to UD3P raid

Guys

I forgot to leave this comment, i asked that "if i have to re install the RAID 0 as i was swapping Maximus II to Giga UD3P", well the answer is NO, i had no need to do it, i just set RAID on bios and everything worked as a charm...

Also i did this from the Asus P5K deluxe P35 to the Asus Maximus II Formula P45 and same system still working on the Giga UD3P :)

Cheers ! :up:
Sergio
03-25-2009, 07:20 AM
andressergio

Quote:

Originally Posted by OC Nub

Was able to get the Vcore down and also MCH :D. Temps were a few c better, max was 72c. Have not primed it with these voltages yet, may try that tonight.

Nice mate :up:

But if i set 1,29+ on bios i get 1,264 vcore IDLE / LOAD not 1,248...my settings are on 1,28125 and gives me 1,248 LOAD and IDLE.

Cheers
Sergio
03-25-2009, 08:54 AM
OC Nub

Quote:

Originally Posted by andressergio

Nice mate :up:

But if i set 1,29+ on bios i get 1,264 vcore IDLE / LOAD not 1,248...my settings are on 1,28125 and gives me 1,248 LOAD and IDLE.

Cheers
Sergio

Thanks.
I tried 1.2875v bios but failed on 7th pass, bumped it up 1 notch and passed. Have LLC enabled, still get a little vdroop but not bad at all. Pretty happy with the CPU now, runs great.
03-25-2009, 09:03 AM
pangingIII

EP45T-UD3R F1

testing >> Crucial Value DDR3-1333 CAS9-9-9 2x2GB D9JNM @ DDR2000 CAS8-8-8 <<

tRD 9 (bios set) 1.92v

http://img514.imageshack.us/img514/3...3252009581.png

tRD 8 (bios set) 1.92v

http://img91.imageshack.us/img91/114...0325222052.png
03-25-2009, 09:19 AM
Leeghoofd

Nice results mate, I'm giving up on my EP45T UD3P; It only works fine with low voltage kits (read I7 kits at high speeds)
Once I put in a high voltage kit (+1.9v) the Vdimm goes bezerk and I can't maintain any stability... board had this issue form day one and an RMA might be the only way solve my issue
03-25-2009, 10:26 AM
pangingIII

EP45T-UD3R F1

>> Crucial Value DDR3-1333 CAS9-9-9 2x2GB @ DDR1600 CAS7-6-6 <<

tRD 8 (bios set) 1.88v
http://img511.imageshack.us/img511/3...0326005952.png

>> Crucial Value DDR3-1333 CAS9-9-9 2x2GB @ DDR1600 CAS7-7-7 <<

tRD 9 (bios set) 1.68v
http://img511.imageshack.us/img511/1...0326012112.png
03-25-2009, 10:36 AM
Ghostleader

Quote:

Originally Posted by darthvedor

Hi,

The Hardware is:

Intel E8600 E0
Cellshock PC3-14400 (DDR3-1800) 2GB DDR3 Kit
Sapphire ATI Radeon HD 4870 512MB GDDR5
Corsair HX620
Cpu cool by Tuniq Tower 120

is safe to give more cpu vcore on air?
Thks

It shouldn´t be any probably to give it ~1,36 and about heat, if you don´t break 80C during LinX no problem, you don´t come close to that heat when you run Prime 95 small FFT, play game or rendering and if the CPU gets to hot it throttle down.

Quote:

Originally Posted by pangingIII

EP45T-UD3R F1

testing >> Crucial Value DDR3-1333 CAS9-9-9 2x2GB D9JNM @ DDR2000 CAS8-8-8 <<

Hi pangingIII :)

Nice memory sticks you have there. :up:

If you remembered I had some problem with my EP45-UD3P, RMA it, they couldn´t fix it, got a new board, it´s working as it should, nice piece of machinery. :up:
03-25-2009, 11:30 AM
xbiusx

Hi, i was playing with my rig and i got this.
http://s11.photobucket.com/albums/a1...l_settings.jpg

Now i`m going to play with more fsb!!!
03-25-2009, 11:47 AM
Ghostleader

Quote:

Originally Posted by xbiusx

Hi, i was playing with my rig and i got this.

Now i`m going to play with more fsb!!!

Nice work. :up:

Lets see how high you can go, 550+ shouldn´t be any problem for you. ;)
03-25-2009, 12:10 PM
SiliconManC

Quote:

Originally Posted by SiliconManC

Hi

I've just got the ep45-ud3p rev. 1.0 to replace my abit ip35 pro and I am having problems with overclocking my Q9550 (L837B542). The problem is that I can't overclock at ALL. Even if I set the fsb to 340 the board don't boot. With abit I was at 8.5*435=3.7GHz with 1,23vcore mch 1,44, mem@1044MHz with 5-5-5-15 everything else was at default. Any suggestions?

My specs is:

Q9550 (L837B542)
ep45-ud3p rev. 1.0 bios f9b
2x2GB Crucial Ballistix 800MHz (BL2564AA80A)@modded Corsair Airflow
sapphire ati 3870
enermax infinity 650W

WC
silverprop cyclone ve
swiftech mcw60
bixII with 2 coolermaster led fans
eheim 1250
t-line

I found the problem. The problem was the Coolguard function of my Enermax. I changed my enermax with my old trust no-name 460W psu and ep45-ud3p clocks well now. So Enermax infinity+ep45-ud3p = NO GO! at least for overclocking.
03-25-2009, 12:35 PM
xbiusx

Quote:

Originally Posted by Ghostleader

Nice work. :up:

Lets see how high you can go, 550+ shouldn´t be any problem for you. ;)

Thanks. But i`m not so sure about 550+, i saw my vcore it took this amount to stabilize 500x8.5... but i`m pretty happy with 4.3 that will be my next step.
03-25-2009, 01:29 PM
radaja

i cant believe how hard it is to sell my 9650 and g.skill2x2GB 9600's.im really getting desperate to get back to a dual core so i can have some fun with this board again.
03-25-2009, 01:56 PM
Jor3lBR

Quote:

Originally Posted by radaja

i cant believe how hard it is to sell my 9650 and g.skill2x2GB 9600's.im really getting desperate to get back to a dual core so i can have some fun with this board again.

If I didn't had to pay a little 'fortune' to IRS in April I would definitely keep your G.Skills man :up:

I'm sad the Quad family is losing one of its clockers thou.

Show 100 post(s) from this thread on one page

** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P