Printable View
had the same issue on my first board. temps even reached 100C after a few minutes in bios and the board shut itself down!Quote:
Originally Posted by JenBell
replaced the tim brought temps down to about 50C. figured out later, one of the dimm slots was dead so i had the board to rma anyway ...
second board was in the 50C range from the beginning.
as i'm not the first reporting this, there is obviously an issue with tim on some boards.
I had the same temps when i got the board.Quote:
Originally Posted by JenBell
1) replace the stock IOH heatsink with optional one
2) clean the paste and apply as5
3) if your case take side fans push fresh air directry to IOH and ICH
With ambient around 23c you must have ~40c on ICH/IOH
http://img833.imageshack.us/img833/1483/temps1600.png
^^ What have you been able to manage for max oc on your 960? I put mine in last night because of my bclk limitation with the board, but even with the 25multi my chip sucks.
23x192 (4400+) with ht on and 1.42 vcore is the max i can do with this chip.Quote:
Originally Posted by OC Nub
Always with my corsair h50.
Nice, better than my chip will do, even on cool water.
Quote:
Originally Posted by Phatonian71
Quote:
Originally Posted by bro20000
Im sorry... HOW THE HELL is that a good result?
THis board costs 400-600$ in europe some places. Ive seen ppl doing 260BCLK on this board, thats a GOOD result.
I mean anyone doing UNDER 230BCLK on this board is PATHETIC.
Ive read through some 5-10pages at the moment this thread and most of it is bollocks, does noone know how to overclock anymore?
Im paffeled, whats happened to this forum... no one overclocks, all i can see is that u guys have big pockets full of money, buy expensive stuff to run them at default speeds... ffs
Im sorry if I hurt someone now...
Hi
is this normal with an Intel I7 970 (hexacores),
the CPU temperature is higher than those of cores? (with Everest beta 5.50.2253)
http://img413.imageshack.us/img413/1016/capturenee.png
thanks ;)
:yepp: its normalQuote:
Originally Posted by tistou77
ok, with the i7 920, was reversed (if I remember) :D
they added the extreme just for kicks lolQuote:
Originally Posted by PlatoonSgtElias
i see most in here just happy with 4.0-4.2 :rofl:
my board is in the box where it belongs
i really wanna see some people who are running the board 220blk withought slow mode on air or water
4500 for blooms is not a good result?
my board can run 230 blck np
i'll post some screens when back home if u need proof
THIS IS A MOTHERBOARD thread, Rampage Extreme III not a CPU board where u brag how much u got from your cpu.Quote:
Originally Posted by playground
ANY board can do 215BCLK, ANY!
Well okey, except some udderly bad boards that can do only 205-210.
Most arent doing what you would consider good because the board combined with bloomfield for many=fail at anything over 215-220bclk without the use of slowmode. Higher bclk for most users I have seen requires slowmode to be enabled, which for a 24/7 rig and any 3D sucks. People still post about how great it is but everytime I read to catch up on whats going on in the thread I leave thinking "WTF am I missing, why are they still praising this pathetic board"? Im not knocking anyone that has 4500stable, thats a very good 24/7 oc by anyones standard but I would give more credit to the chip and the guy clocking it than to this board. That can be accomplished on many lower priced boards.Quote:
Originally Posted by PlatoonSgtElias
zpaf...some questions:Quote:
Originally Posted by zpaf
1. Is the fan noisy? Really dont want to spoil the PC by adding a noisy fan
2. Clean TIM...not an option. Simply dont have the time to do it...plus if I did do it I dont think I could help but get the EK mobo WB instead and build a dedicated WCing loop for it while I am at it. I dont want upgrade anything in the PC at the moment, just built it recently and need to spend time using rather than improving it right now.
3. Case is TJ07. Air flow is not great. I have a HDD enclosure pushing air through the front to back. Also have rear 92mm's and roof 120mm fans all pushing air. No direct air flow over the mobo though. Any advice on how to go about improving air flow?
I am thinking that if I can add the optional fan on without undoing the whole mobo then I'll give that a go and see how it sounds. If it reduces the temps then great. If the fan is noisy then I am thinking that an ugly but effective solution could be antec spot cool fans. If the optional fan is good but not good enough then adding the ugly spot fans will further reduce the temps while avoiding a complete re-build (something that only a mobo/cpu failure will make me do...touch wood...crosses fingers...prays to the hw gods for mercy...er...).
Any advice would greatly appreciated;)
have not used the optional fan myself but have read its rather loud. so if noise is an issue and you would like to bring temps down a bit i would instead undervolt a 120mm fan and point it directly in the direction of the ioh/ich heatsink.Quote:
Originally Posted by JenBell
but my advice is: if you dont have any problems, and i doubt you will have any, just leave it as it is! your temps are higher as normal but still within operating specs of intel, so what.
Quote:
Originally Posted by PlatoonSgtElias
Hate to break it to you man, but very few Bloomfield chips are stable above ~4.4GHz without subzero cooling. The motherboard has little to nothing to do with that.Quote:
Originally Posted by PlatoonSgtElias
Where this board does shine is for CPU-Z, SuperPi, and WPrime as it can go past any other board with QPI Slow Mode enabled.
If anything, it sounds like you've come in here to show off your 5.1GHz overclock. I only run my W3520 at 4.2GHz... Beat my benching clocks and then you can brag. Until then, it would be wonderful if you'd stop demonstrating to everyone how easy it is to be an ass on the internet.
fgw...I had a feeling it would be. I like the idea of 120mm fan...something like a 1200-2000rpm 120mm fan (one or two) sounds good. Question is how I hold them in place? I dont have a heatsink I can hand it off of. Anyone with any ideas? Antec spot cool is looking increasing like something I might have to go with...which will mean I will need to install the fan controller I've been holding off installing as I'll end up spending ages sorting on niggling things that have been getting to me (few messy cables...more UV lighting...move around the LEDs to under mobo tray, re-cable all the fans from 7v to 12v at full RPM (at max the fans are really quite as well...should of thought of this before).Quote:
Originally Posted by fgw
what is on the 970 and 980X probes cores are bugged?
CPU temp is higher than those of cores, and the temperatures of the cores is lower than the ambient temperature or that of water (WC)
I Used bios 0011
thanks ;)
I picked up a second i7 930 from newegg. FPO/Batch #: 3012A752 (pack date 7/07/10). On my R3E it wouldn't do more than 3.82GHz at 191BCLK.Quote:
Originally Posted by bassplayer
My first i7 930 does 4.37GHz at 230BCLK on the R3E, but I run it at 4.2GHz with a 200BCLK for daily use to keep temps under control.
quoted for truth.Quote:
Originally Posted by bassplayer
Whats the BEST bios for this Board ? using a 980X
Im thinking my board cant go 216 and higher ! tried every volt up and down :/ is this possible ? anyone got this prob ? what should i do ? can i rma this !
have you tryed raising the pci-e frequency?Quote:
Originally Posted by AceBaran
yes up till 110 IOH up till 1.25.. no bsod just freez
Am linX stable 20 runns bclk 215 x 17.. i go 216 and wich ever volt i up or down, even loose timings on ram 9-9-9-24..
some 920 fun :) not maxed, need to use marvell ports next time pci-e @ 128
http://valid.canardpc.com/show_oc.php?id=1394377
some 920 fun :) not maxed, need to use marvell ports next time pci-e @ 128
http://valid.canardpc.com/show_oc.php?id=1394377