Give a link to the set for info on timings and voltages...Quote:
Originally Posted by Racpu_
Try these settings in bios...
Printable View
Give a link to the set for info on timings and voltages...Quote:
Originally Posted by Racpu_
Try these settings in bios...
It could be your sticks 1.6v seems abit low for 1600Mhz at 8-8-8-24 1T! Have you try 1.7/1.8Quote:
Originally Posted by Racpu_
I had a similar problem with Vista 64 going down when I unlocked the 4th core but after a reinstall I can boot to Vista 64, W7 or XP with no issues and running a 1600MHZ 7-7-7-21-29 1T.
Hope you find a solution.
Has anyone had there memory over 1680Mhz with this board in bios! Seems to be my limit on this board! I know my sticks can do 2100Mhz on intel boards thou!
what chips do they use?Quote:
Originally Posted by bro20000
Click - Info in the Specs
Also found the same info elsewhere, but cannot find it now, lol.
Ooops, sorry, just realised that spec request wasn't for me, lol :)
Samsung K4B1G0846D-HCF8Quote:
Originally Posted by msimax
I Try this settings, and it was ok ... placing the 3700 is no longer stable, but try more Mhz's only just up the CPU Voltage Control or need to change anything else?Quote:
Originally Posted by keenan
Thanks for the settings.
:up:
Bank Swizzle Mode, DQS Training control ....whats the scope on those two?
From my research, Bank Swizzle should increase the bandwidth when enabled ( I didnt notice anything) and DQS control when enabled should help to stabilize when pushing RAM too hard.
Just up the voltage... try 1.55V for 3.7GhzQuote:
Originally Posted by Racpu_
Ok, What is the maximum voltage use 24/7 and the temperature?
What's the recommended Bios for this board F4 or F3l?
I use F3l... :)
f4g ;)
Had say F3i Lastest and offical by Gigabyte!
I have 4GB(2x2GB) of Patriot Viper rated to run at 1600mhz, 7-7-7-20 with 1.9v. These modules are supposed to be compatible with UD5P according to Gigabyte, yet they cannot run at rated speed and timing.
I've tried 4 bioses that have been available at Gigabyte site, but none of them worked with these modules.
Any ideas?
Am in the same boat mate! I guess with newer bios coming out they will fix the issues!
I am back to F4d bios. Tried them all. The Patriot 34G1600LLK I'm using has occasional issues at 7-7-7-20/1.9v It will run games but fails OCCT after 7-15 minutes. Called Patriot and they said just set the 7-7-7-20 and leave the rest timings alone. SPD is "supposed" to be 7-7-7-20-36-2T but runs stable during OCCT at 7-7-7-20-26-2T. So this is what's running now-3.4Ghz (200 x 17) +0.050v
Edit: I can game all night on settings that wouldn't last 5 minutes of OCCT.
Has anyone managed to get the new T1 Beta Bios
the new pot with DIce performs good
http://img510.imageshack.us/img510/1...eenshot068.png
By deeodee
http://img113.imageshack.us/img113/906/scr8130680.jpg
By deeodee
Yeah I call that VERY good. :-)
Any news on the bios?
Guys, is there any point to OCing the HT link? I dont notice anything between 2000 and 2600...at least not on CPU or memories tests. With the NB Ocing the difference is obvious.
try with 2 4870x2 start @ 1600 onwards youll see the gain but you wont notice no performance difference if your setup is not starved for bandwidth at any giving speed
also im trying to see if they can crank out a very mem friendly bios:D
So if my GTX280 needs more bandwitdh then thats where I will see the difference...I see. Well, its cool to have it so high anyway. :-)
I'm having problem with my UD5P holding on to the overclocked setting when I cold boot. Everytime I cold boot my system it reports that my overclocked bios setting is not stable even though the system passes both 2 hours of OCCT and 3 hours of Prime95 under Vista64. I have F3b and set FSB to 250mhz. What am I doing wrong?
http://img140.imageshack.us/img140/8798/screenz.jpg